Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › 2021.02–2022.01
RM33C0E _59 Vehicle Exterior _065470 MIRROR (EXT) _0332577 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Retractable Mirrors do not Operate with Power Retract Mirror Switch  


DESCRIPTION

The outer mirror switch assembly sends the retractable outer mirror switch signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the mirror retract/return signal to each outer mirror control ECU assembly via CAN communication. Based on the signal, each outer mirror control ECU assembly retracts or returns its corresponding outer rear view mirror assembly.

WIRING DIAGRAM

for LHD


B495521E07
0.167,2.469 1.375,2.969 1.208,0.5 10 false Outer Mirror Switch Assembly 0.708,5.396 2.698,5.594 1.99,0.198 10 false : CAN Communication Line 1.573,4.375 2.448,4.583 0.875,0.208 10 false K53 1.573,4.542 3.219,5.156 1.646,0.615 10 false Main Body ECU (Multiplex Network Body ECU) 0.156,2.313 1.031,2.521 0.875,0.208 10 false O25 1.063,0.521 1.938,0.729 0.875,0.208 10 false MR 1.167,1.698 2.042,1.906 0.875,0.208 10 false E 1.365,0.427 2.24,0.635 0.875,0.208 10 false 10 1.375,1.604 2.25,1.813 0.875,0.208 10 false 7 1.656,0.427 2.531,0.635 0.875,0.208 10 false 16 1.896,0.51 2.771,0.719 0.875,0.208 10 false RET 3.719,1.792 4.594,2 0.875,0.208 10 false O9 3.719,1.958 5.26,2.438 1.542,0.479 10 false Outer Mirror Control ECU Assembly (Driver Door) 3.583,4.51 5.135,5.24 1.552,0.729 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.583,4.344 4.458,4.552 0.875,0.208 10 false N10 4.698,0.365 5.573,0.573 0.875,0.208 10 false MR+ 4.708,1.396 5.583,1.604 0.875,0.208 10 false MR- 5.104,0.26 5.979,0.469 0.875,0.208 10 false 3 5.073,1.313 5.948,1.521 0.875,0.208 10 false 11 5.333,0.125 6.208,0.333 0.875,0.208 10 false 3*1 5.281,0.271 6.156,0.479 0.875,0.208 10 false 19*2 5.625,0.26 6.5,0.469 0.875,0.208 10 false MR 5.625,1.333 6.5,1.542 0.875,0.208 10 false MF 5.552,1.802 6.563,2.083 1.01,0.281 10 false O21*1, O22*2 5.552,1.969 6.979,2.563 1.427,0.594 10 false Outer Rear View Mirror Assembly (Driver Door) 5.844,0.563 6.74,0.99 0.896,0.427 10 false Power Retract Mirror Motor 5.573,4.406 6.448,4.615 0.875,0.208 10 false N17*1, N24*2 5.573,4.563 7,5.354 1.427,0.792 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 1.375,1.01 2.25,1.219 0.875,0.208 10 false 8 1.719,1.01 2.594,1.219 0.875,0.208 10 false 9 1.094,1.104 1.969,1.313 0.875,0.208 10 false E2 1.906,1.115 2.781,1.323 0.875,0.208 10 false MIRE 5.854,3.208 6.75,3.635 0.896,0.427 10 false Power Retract Mirror Motor 5.625,2.865 6.5,3.073 0.875,0.208 10 false MR 5.635,3.917 6.51,4.125 0.875,0.208 10 false MF 5.104,2.865 5.979,3.073 0.875,0.208 10 false 3 5.083,3.917 5.958,4.125 0.875,0.208 10 false 11 4.698,2.969 5.573,3.177 0.875,0.208 10 false MR+ 4.729,4.01 5.604,4.219 0.875,0.208 10 false MR- 5.281,1.313 6.156,1.521 0.875,0.208 10 false 20*2 5.271,1.146 6.146,1.354 0.875,0.208 10 false 11*1 5.292,3.917 6.167,4.125 0.875,0.208 10 false 20*2 5.281,3.76 6.156,3.969 0.875,0.208 10 false 11*1 5.292,2.854 6.167,3.063 0.875,0.208 10 false 19*2 5.354,2.698 6.229,2.906 0.875,0.208 10 false 3*1 2.781,5.479 4.771,5.677 1.99,0.198 10 false *1: for 16 Pin Connector 4.615,5.479 6.604,5.677 1.99,0.198 10 false *2: for 22 Pin Connector


for RHD


B495521E08
0.167,2.469 1.375,2.969 1.208,0.5 10 false Outer Mirror Switch Assembly 0.708,5.396 2.698,5.594 1.99,0.198 10 false : CAN Communication Line 1.573,4.375 2.448,4.583 0.875,0.208 10 false K53 1.552,4.531 3.198,5.146 1.646,0.615 10 false Main Body ECU (Multiplex Network Body ECU) 0.167,2.313 1.042,2.521 0.875,0.208 10 false N25 0.927,0.51 1.802,0.719 0.875,0.208 10 false MR*2 1.167,1.698 2.042,1.906 0.875,0.208 10 false E 1.344,0.427 2.219,0.635 0.875,0.208 10 false 10*2 1.375,1.604 2.25,1.813 0.875,0.208 10 false 7 1.656,0.427 2.531,0.635 0.875,0.208 10 false 16 1.896,0.51 2.771,0.719 0.875,0.208 10 false RET 3.719,1.792 4.594,2 0.875,0.208 10 false N10 3.719,1.958 5.26,2.438 1.542,0.479 10 false Outer Mirror Control ECU Assembly (Driver Door) 3.583,4.51 5.135,5.24 1.552,0.729 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.583,4.344 4.458,4.552 0.875,0.208 10 false O9 4.698,0.365 5.573,0.573 0.875,0.208 10 false MR+ 4.708,1.396 5.583,1.604 0.875,0.208 10 false MR- 5.104,0.26 5.979,0.469 0.875,0.208 10 false 3 5.073,1.313 5.948,1.521 0.875,0.208 10 false 11 5.375,0.26 6.25,0.469 0.875,0.208 10 false 19 5.625,0.26 6.5,0.469 0.875,0.208 10 false MR 5.625,1.333 6.5,1.542 0.875,0.208 10 false MF 5.583,4.406 6.594,4.688 1.01,0.281 10 false O22 5.552,1.969 6.979,2.563 1.427,0.594 10 false Outer Rear View Mirror Assembly (Driver Door) 5.844,0.563 6.74,0.99 0.896,0.427 10 false Power Retract Mirror Motor 5.563,1.802 6.438,2.01 0.875,0.208 10 false N24 5.573,4.563 7,5.354 1.427,0.792 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 1.375,1.01 2.25,1.219 0.875,0.208 10 false 8 1.719,1.01 2.594,1.219 0.875,0.208 10 false 9 1.094,1.104 1.969,1.313 0.875,0.208 10 false E2 1.906,1.115 2.781,1.323 0.875,0.208 10 false MIRE 5.854,3.208 6.75,3.635 0.896,0.427 10 false Power Retract Mirror Motor 5.625,2.865 6.5,3.073 0.875,0.208 10 false MR 5.635,3.917 6.51,4.125 0.875,0.208 10 false MF 5.104,2.865 5.979,3.073 0.875,0.208 10 false 3 5.083,3.917 5.958,4.125 0.875,0.208 10 false 11 4.698,2.969 5.573,3.177 0.875,0.208 10 false MR+ 4.729,4.01 5.604,4.219 0.875,0.208 10 false MR- 5.375,1.313 6.25,1.521 0.875,0.208 10 false 20 5.365,3.917 6.24,4.125 0.875,0.208 10 false 20 5.365,2.854 6.24,3.063 0.875,0.208 10 false 19 1.365,0.281 2.24,0.49 0.875,0.208 10 false 9*1 0.219,4.021 1.354,4.458 1.135,0.438 10 false *1: w/o Automatic Retractable Mirror 0.219,4.698 1.354,5.115 1.135,0.417 10 false *2: w/ Automatic Retractable Mirror 0.938,0.365 1.813,0.573 0.875,0.208 10 false MF*1


CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Outer Mirror Fold SW Retractable outer mirror switch signal OFF or ON OFF: Retractable outer mirror switch not in retract position
ON: Retractable outer mirror switch in retract position
-
Body Electrical > Main Body > Data List
Tester Display
Outer Mirror Fold SW
50003 123 104
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

11.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)
2.PERFORM ACTIVE TEST USING GTS
a.

Enter the following menus: Body Electrical / Mirror L or Mirror R / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Mirror L > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Fold/Return Mirror retract operation OFF, Return or Fold
·

Operate with the power switch on (IG) and the vehicle stopped.

·

This test activates the Fold / Return.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Body Electrical > Mirror L > Active Test
Tester Display
Mirror Fold/Return
50004 225 4
Body Electrical > Mirror R > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Fold/Return Mirror retract operation OFF, Return or Fold
·

Operate with the power switch on (IG) and the vehicle stopped.

·

This test activates the Fold / Return.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Body Electrical > Mirror R > Active Test
Tester Display
Mirror Fold/Return
50004 224 4

Result:
Result Proceed to
Outer rear view mirror assemblies operate normally A
Outer rear view mirror assembly (driver door) does not operate normally B
Outer rear view mirror assembly (front passenger door) does not operate normally C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR))

C

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) - OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR))
3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR))
a.

for LHD:

i.

Disconnect the O9 outer mirror control ECU assembly (driver door) connector.


ii.

Disconnect the O21*1 or O22*2 outer rear view mirror assembly (driver door) connector.

*1: for 16 Pin Connector

*2: for 22 Pin Connector



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 16 Pin Connector
Tester Connection Condition Specified Condition
O9-3 (MR+) - O21-3 (MR) Always Below 1 Ω
O9-11 (MR-) - O21-11 (MF) Always Below 1 Ω
O9-3 (MR+) or O21-3 (MR) - Body ground Always 10 kΩ or higher
O9-11 (MR-) or O21-11 (MF) - Body ground Always 10 kΩ or higher

for 22 Pin Connector
Tester Connection Condition Specified Condition
O9-3 (MR+) - O22-19 (MR) Always Below 1 Ω
O9-11 (MR-) - O22-20 (MF) Always Below 1 Ω
O9-3 (MR+) or O22-19 (MR) - Body ground Always 10 kΩ or higher
O9-11 (MR-) or O22-20 (MF) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the N10 outer mirror control ECU assembly (driver door) connector.


ii.

Disconnect the N24 outer rear view mirror assembly (driver door) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N10-3 (MR+) - N24-19 (MR) Always Below 1 Ω
N10-11 (MR-) - N24-20 (MF) Always Below 1 Ω
N10-3 (MR+) or N24-19 (MR) - Body ground Always 10 kΩ or higher
N10-11 (MR-) or N24-20 (MF) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (RETRACTABLE MIRROR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (RETRACTABLE MIRROR)
a.

Remove the outer rear view mirror assembly (driver door).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly (driver door)(retractable mirror).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)
a.

Temporarily replace the outer mirror control ECU assembly (driver door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK POWER RETRACT MIRROR FUNCTION
6.CHECK POWER RETRACT MIRROR FUNCTION
a.

Check the power retract mirror function operates normally.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Power retract mirror function operates normally.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) - OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR))
a.

for LHD:

i.

Disconnect the N10 outer mirror control ECU assembly (front passenger door) connector.


ii.

Disconnect the N17*1 or N24*2 outer rear view mirror assembly (front passenger door) connector.

*1: for 16 Pin Connector

*2: for 22 Pin Connector



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 16 Pin Connector
Tester Connection Condition Specified Condition
N10-3 (MR+) - N17-3 (MR) Always Below 1 Ω
N10-11 (MR-) - N17-11 (MF) Always Below 1 Ω
N10-3 (MR+) or N17-3 (MR) - Body ground Always 10 kΩ or higher
N10-11 (MR-) or N17-11 (MF) - Body ground Always 10 kΩ or higher

for 22 Pin Connector
Tester Connection Condition Specified Condition
N10-3 (MR+) - N24-19 (MR) Always Below 1 Ω
N10-11 (MR-) - N24-20 (MF) Always Below 1 Ω
N10-3 (MR+) or N24-19 (MR) - Body ground Always 10 kΩ or higher
N10-11 (MR-) or N24-20 (MF) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the O9 outer mirror control ECU assembly (front passenger door) connector.


ii.

Disconnect the O22 outer rear view mirror assembly (front passenger door) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-3 (MR+) - O22-19 (MR) Always Below 1 Ω
O9-11 (MR-) - O22-20 (MF) Always Below 1 Ω
O9-3 (MR+) or O22-19 (MR) - Body ground Always 10 kΩ or higher
O9-11 (MR-) or O22-20 (MF) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (RETRACTABLE MIRROR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (RETRACTABLE MIRROR)
a.

Remove the outer rear view mirror assembly (front passenger door).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly (front passenger door)(retractable mirror).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)

9.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)
a.

Temporarily replace the outer mirror control ECU assembly (front passenger door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK POWER RETRACT MIRROR FUNCTION
10.CHECK POWER RETRACT MIRROR FUNCTION
a.

Check the power retract mirror function operates normally.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Power retract mirror function operates normally.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

11.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly (w/ memory).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)

12.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the O25*1 or N25*2 outer mirror switch assembly.

*1: for LHD

*2: for RHD



b.

Disconnect the K53 main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
O25-10 (MR) - K53-16 (RET) Always Below 1 Ω
O25-10 (MR) or K53-16 (RET) - Body ground Always 10 kΩ or higher
O25-8 (E2) - K53-9 (MIRE) Always Below 1 Ω
O25-8 (E2) or K53-9 (MIRE) - Body ground Always 10 kΩ or higher
O25-7 (E) - K53-9 (MIRE) Always Below 1 Ω
O25-7 (E) or K53-9 (MIRE) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
N25-9 (MF) - K53-16 (RET)*1 Always Below 1 Ω
N25-9 (MF) or K53-16 (RET) - Body ground*1 Always 10 kΩ or higher
N25-10 (MR) - K53-16 (RET)*2 Always Below 1 Ω
N25-10 (MR) or K53-16 (RET) - Body ground*2 Always 10 kΩ or higher
N25-8 (E2) - K53-9 (MIRE) Always Below 1 Ω
N25-8 (E2) or K53-9 (MIRE) - Body ground Always 10 kΩ or higher
N25-7 (E) - K53-9 (MIRE) Always Below 1 Ω
N25-7 (E) or K53-9 (MIRE) - Body ground Always 10 kΩ or higher


*1: w/o Automatic Retractable Mirror

*2: w/ Automatic Retractable Mirror



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR