Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2021.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331857 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1850  Short in Rear Side Squib RH Circuit  B1851  Open in Rear Side Squib RH Circuit  B1852  Short to GND in Rear Side Squib RH Circuit  B1853  Short to B+ in Rear Side Squib RH Circuit  


DESCRIPTION

The rear side squib RH circuit consists of the airbag sensor assembly and rear seat airbag assembly RH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear side squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1850 Short in Rear Side Squib RH Circuit
·

The airbag sensor assembly detects a line short in the rear side squib RH circuit during the primary check.

·

Rear side squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib RH (Rear seat airbag assembly RH)

·

Airbag sensor assembly


Comes on Applies to check mode
B1851 Open in Rear Side Squib RH Circuit
·

The airbag sensor assembly detects an open in the rear side squib RH circuit.

·

Rear side squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib RH (Rear seat airbag assembly RH)

·

Airbag sensor assembly


Comes on Applies to check mode
B1852 Short to GND in Rear Side Squib RH Circuit
·

The airbag sensor assembly detects a short to ground in the rear side squib RH circuit.

·

Rear side squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib RH (Rear seat airbag assembly RH)

·

Airbag sensor assembly


Comes on Applies to check mode
B1853 Short to B+ in Rear Side Squib RH Circuit
·

The airbag sensor assembly detects a short to B+ in the rear side squib RH circuit.

·

Rear side squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib RH (Rear seat airbag assembly RH)

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B475055E39
4.896,3.083 7.146,3.49 2.25,0.406 10 false Airbag Sensor Assembly 4.885,2.917 6.552,3.438 1.667,0.521 10 false R31 4.708,1.333 5.51,1.979 0.802,0.646 10 false 12 4.719,1.896 5.521,2.542 0.802,0.646 10 false 11 4.958,1.333 5.76,1.979 0.802,0.646 10 false SRR+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false SRR- 0.875,2.406 2.542,2.927 1.667,0.521 10 false R50 0.875,2.573 2.635,3.125 1.76,0.552 10 false Rear Side Squib RH (Rear Seat Airbag Assembly RH) 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.625,1.333 2.427,1.979 0.802,0.646 10 false SRR+ 1.635,1.885 2.438,2.531 0.802,0.646 10 false SRR-

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238348C01
0.531,1.198 0.531,0.688 0.531,0.688 0.708,0.688 false 1.365,1.198 1.365,0.688 1.365,0.688 1.542,0.688 false 0.656,1.188 1.052,1.438 0.396,0.25 10 D 1.031,1.188 1.354,1.427 0.323,0.24 10 C 1.604,1.188 1.938,1.552 0.333,0.365 10 B 1.99,1.188 2.333,1.542 0.344,0.354 10 A 2.438,0.896 2.75,1.208 0.313,0.313 10 *2 0.76,0.604 1.021,0.854 0.26,0.25 10 *1 1.583,0.604 1.854,0.896 0.271,0.292 10 *3
*1 Rear Seat Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear seat airbag assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear seat airbag assembly RH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT AIRBAG ASSEMBLY RH

NG

REPLACE FLOOR WIRE

2.CHECK REAR SEAT AIRBAG ASSEMBLY RH
a.
C290010C26
0.417,2.333 0.833,2.583 0.417,0.25 0.604,0.896 0.604,0.396 0.604,0.396 0.354,0.396 false 2.208,2.458 2.458,2.458 false 2.49,2.385 2.948,2.583 0.458,0.198 10 false SST 0.51,2.375 0.906,2.729 0.396,0.354 10 false R50 0.344,1.615 0.74,1.969 0.396,0.354 10 false *a 0.198,0.313 0.594,0.667 0.396,0.354 10 false *1 2.5,0.583 2.896,0.938 0.396,0.354 10 false *2 0.719,0.896 1.115,1.25 0.396,0.354 10 false D 1.104,0.896 1.5,1.25 0.396,0.354 10 false C 1.854,0.896 2.25,1.25 0.396,0.354 10 false B 2.021,0.896 2.417,1.25 0.396,0.354 10 false A
*1 Rear Seat Airbag Assembly RH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Rear Seat Airbag Assembly RH)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear seat airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1850, B1851, B1852 or B1853 is not output.


HINT:

Codes other than DTCs B1850, B1851, B1852 and B1853 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
C238257C64
0.417,2.417 0.833,2.667 0.417,0.25 1.292,2.688 0.906,2.99 false 1.885,2.99 1.49,2.688 false 0.708,1.083 0.708,0.573 0.708,0.573 0.479,0.573 false 1.417,1.083 1.417,0.573 1.417,0.573 1.188,0.573 false 0.833,1.073 1.146,1.323 0.313,0.25 10 false D 1.146,1.073 1.49,1.427 0.344,0.354 10 false C 1.604,1.073 1.875,1.354 0.271,0.281 10 false B 1.906,1.073 2.24,1.396 0.333,0.323 10 false A 2.313,0.792 2.656,1.135 0.344,0.344 10 false *2 0.323,0.49 0.604,0.729 0.281,0.24 10 false *1 0.219,1.813 0.51,2.104 0.292,0.292 10 false *a 1.75,3 2.198,3.229 0.448,0.229 10 false SRR- 0.75,3 1.313,3.323 0.563,0.323 10 false SRR+ 1.042,0.5 1.406,0.792 0.365,0.292 10 false *3 0.5,2.448 0.938,2.719 0.438,0.271 10 false R50
*1 Rear Seat Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Rear Seat Airbag Assembly RH)


Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R50-1 (SRR+) - Body ground Power switch on (IG) Below 1 V
R50-2 (SRR-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R50-1 (SRR+) - R50-2 (SRR-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R50-1 (SRR+) - Body ground Always 1 MΩ or higher
R50-2 (SRR-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R50-1 (SRR+) - R50-2 (SRR-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238241C01
0.844,1.292 0.844,0.844 0.844,0.844 0.552,0.844 false 0.396,0.781 0.729,1.083 0.333,0.302 10 false *1 0.979,1.302 1.156,1.531 0.177,0.229 10 false D 1.135,1.302 1.344,1.5 0.208,0.198 10 false C 1.583,1.302 1.781,1.5 0.198,0.198 10 false B 1.74,1.302 1.938,1.542 0.198,0.24 10 false A 2.146,1.021 2.438,1.26 0.292,0.24 10 false *2
*1 Rear Seat Airbag Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the rear seat airbag assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1850, B1851, B1852 or B1853 is not output.


HINT:

Codes other than DTCs B1850, B1851, B1852 and B1853 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG