Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2021.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331857 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1855  Short in Rear Side Squib LH Circuit  B1856  Open in Rear Side Squib LH Circuit  B1857  Short to GND in Rear Side Squib LH Circuit  B1858  Short to B+ in Rear Side Squib LH Circuit  


DESCRIPTION

The rear side squib LH circuit consists of the airbag sensor assembly and rear seat airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear side squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1855 Short in Rear Side Squib LH Circuit
·

The airbag sensor assembly detects a line short in the rear side squib LH circuit during the primary check.

·

Rear side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib LH (Rear seat airbag assembly LH)

·

Airbag sensor assembly


Comes on Applies to check mode
B1856 Open in Rear Side Squib LH Circuit
·

The airbag sensor assembly detects an open in the rear side squib LH circuit.

·

Rear side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib LH (Rear seat airbag assembly LH)

·

Airbag sensor assembly


Comes on Applies to check mode
B1857 Short to GND in Rear Side Squib LH Circuit
·

The airbag sensor assembly detects a short to ground in the rear side squib LH circuit.

·

Rear side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib LH (Rear seat airbag assembly LH)

·

Airbag sensor assembly


Comes on Applies to check mode
B1858 Short to B+ in Rear Side Squib LH Circuit
·

The airbag sensor assembly detects a short to B+ in the rear side squib LH circuit.

·

Rear side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear side squib LH (Rear seat airbag assembly LH)

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B475055E40
4.896,3.083 7.146,3.49 2.25,0.406 10 false Airbag Sensor Assembly 4.885,2.917 6.552,3.438 1.667,0.521 10 false R32 4.708,1.333 5.51,1.979 0.802,0.646 10 false 13 4.719,1.896 5.521,2.542 0.802,0.646 10 false 14 4.958,1.333 5.76,1.979 0.802,0.646 10 false SRL+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false SRL- 0.875,2.406 2.542,2.927 1.667,0.521 10 false R51 0.875,2.573 2.698,3.094 1.823,0.521 10 false Rear Side Squib LH (Rear Seat Airbag Assembly LH) 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.635,1.333 2.438,1.979 0.802,0.646 10 false SRL+ 1.656,1.885 2.458,2.531 0.802,0.646 10 false SRL-

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238350C01
0.521,1.021 0.521,1.635 false 1.385,0.896 1.385,0.469 1.385,0.469 1.615,0.469 false 0.646,0.875 0.865,1.167 0.219,0.292 10 D 1.052,0.875 1.417,1.281 0.365,0.406 10 C 1.625,0.875 1.938,1.26 0.313,0.385 10 B 2.021,0.875 2.281,1.26 0.26,0.385 10 A 2.469,1.188 2.771,1.625 0.302,0.438 10 *2 0.448,1.656 0.896,1.99 0.448,0.333 10 *1 1.646,0.385 1.969,0.677 0.323,0.292 10 *3
*1 Rear Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear seat airbag assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear seat airbag assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT AIRBAG ASSEMBLY LH

NG

REPLACE FLOOR WIRE

2.CHECK REAR SEAT AIRBAG ASSEMBLY LH
a.
C295801C15
0.417,2.167 0.833,2.417 0.417,0.25 0.594,0.885 0.594,0.552 false 2.208,2.448 2.542,2.448 false 0.521,0.917 0.844,1.188 0.323,0.271 10 false *1 2.5,0.74 2.875,1.063 0.375,0.323 10 false *2 0.333,1.615 0.667,2.031 0.333,0.417 10 false *a 2.583,2.354 2.917,2.771 0.333,0.417 10 false SST 0.51,2.208 0.938,2.573 0.427,0.365 10 false R51 2.021,0.406 2.396,0.729 0.375,0.323 10 false A 1.854,0.406 2.229,0.729 0.375,0.323 10 false B 1.104,0.406 1.479,0.729 0.375,0.323 10 false C 0.729,0.406 1.104,0.729 0.375,0.323 10 false D
*1 Rear Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Rear Seat Airbag Assembly LH)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear seat airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1855, B1856, B1857 or B1858 is not output.


HINT:

Codes other than DTCs B1855, B1856, B1857 and B1858 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
C238352C37
0.51,2.333 0.917,2.583 0.406,0.25 1.406,2.594 1.115,2.854 false 1.875,2.844 1.583,2.583 false 0.563,0.729 0.563,1.177 false 1.375,0.583 1.375,0.198 1.375,0.198 1.531,0.198 false 0.677,0.573 0.896,0.802 0.219,0.229 10 false D 1.063,0.573 1.354,0.854 0.292,0.281 10 false C 1.583,0.573 1.865,0.958 0.281,0.385 10 false B 1.979,0.573 2.208,0.906 0.229,0.333 10 false A 2.406,0.875 2.75,1.25 0.344,0.375 10 false *2 0.5,1.177 0.875,1.469 0.375,0.292 10 false *1 0.313,1.719 0.604,2.01 0.292,0.292 10 false *a 1.854,2.854 2.354,3.125 0.5,0.271 10 false SRL- 0.813,2.854 1.281,3.083 0.469,0.229 10 false SRL+ 1.552,0.115 1.906,0.438 0.354,0.323 10 false *3 0.604,2.375 1.104,2.802 0.5,0.427 10 false R51
*1 Rear Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Rear Seat Airbag Assembly LH)


Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R51-1 (SRL+) - Body ground Power switch on (IG) Below 1 V
R51-2 (SRL-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R51-1 (SRL+) - R51-2 (SRL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R51-1 (SRL+) - Body ground Always 1 MΩ or higher
R51-2 (SRL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R51-1 (SRL+) - R51-2 (SRL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238353C01
0.802,0.833 0.802,1.156 false 0.938,0.708 1.542,1.438 0.604,0.729 10 false D 1.083,0.708 1.49,1.177 0.406,0.469 10 false C 1.594,0.708 1.885,1.094 0.292,0.385 10 false B 1.75,0.708 2.073,1 0.323,0.292 10 false A 2.188,1.021 2.49,1.354 0.302,0.333 10 false *2 0.74,1.167 1.115,1.521 0.375,0.354 10 false *1
*1 Rear Seat Airbag Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the rear seat airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1855, B1856, B1857 or B1858 is not output.


HINT:

Codes other than DTCs B1855, B1856, B1857 and B1858 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG