Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transmits signals via AVC-LAN communication.
If a short to +B or short to ground occurs in an AVC-LAN communication line, the audio and visual system will not function normally because communication is not possible.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
The radio and display receiver assembly is the master unit.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 9 Speakers | B |
A
B
Remove the radio and display receiver assembly.
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K3-5 (TX1+) - K3-6 (TX1-) | Always | 60 to 80 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K3 radio and display receiver assembly connector.
Disconnect the Z1 cooler control switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-7 (TX+) - K3-5 (TX1+) | Always | Below 1 Ω |
| Z1-8 (TX-) - K3-6 (TX1-) | Always | Below 1 Ω |
| Z1-7 (TX+) or K3-5 (TX1+) - Body ground | Always | 10 kΩ or higher |
| Z1-8 (TX-) or K3-6 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect and reconnect each slave unit one by one until the master unit returns to normal.
Check all slave units.
If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.
Master unit returns to normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the radio and display receiver assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K3-5 (TX1+) - K3-6 (TX1-) | Always | 60 to 80 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K3 radio and display receiver assembly connector.
Disconnect the K9 stereo component amplifier assembly connector.
Disconnect the Z1 cooler control switch assembly connector. (w/ Cooler Control Switch Assembly)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K3-5 (TX1+) - K9-8 (TX+) | Always | Below 1 Ω |
| K3-6 (TX1-) - K9-7 (TX-) | Always | Below 1 Ω |
| K9-20 (TXD+) - Z1-7 (TX+)* | Always | Below 1 Ω |
| K9-19 (TXD-) - Z1-8 (TX-)* | Always | Below 1 Ω |
| K3-5 (TX1+) or K9-8 (TX+) - Body ground | Always | 10 kΩ or higher |
| K3-6 (TX1-) or K9-7 (TX-) - Body ground | Always | 10 kΩ or higher |
| K9-20 (TXD+) or Z1-7 (TX+) - Body ground* | Always | 10 kΩ or higher |
| K9-19 (TXD-) or Z1-8 (TX-) - Body ground* | Always | 10 kΩ or higher |
*: w/ Cooler Control Switch Assembly
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect and reconnect each slave unit one by one until the master unit returns to normal.
Check all slave units.
If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.
Master unit returns to normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG