Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.02
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Operating Light Control Rheostat does not Change Light Brightness  


DESCRIPTION

The combination meter assembly receives signals through this circuit to adjust the illumination of the combination meter assembly. The combination meter assembly sets the illumination level based on the user operation of the light control rheostat switch in the trip switch.

WIRING DIAGRAM

E461547E01
6,0.198 6.458,0.396 0.458,0.198 10 false 5 V 4.958,0.51 5.417,0.708 0.458,0.198 10 false TR 4.948,2.375 5.406,2.573 0.458,0.198 10 false SW3 2.531,0.5 2.99,0.698 0.458,0.198 10 false RV 4.75,2.375 5.208,2.573 0.458,0.198 10 false 5 2.938,0.417 3.396,0.615 0.458,0.198 10 false 4 4.75,0.51 5.208,0.708 0.458,0.198 10 false 2 2.927,2.292 3.385,2.49 0.458,0.198 10 false 1 2.625,2.365 3.083,2.563 0.458,0.198 10 false E 1.104,0.781 2.469,1.125 1.365,0.344 10 false Light Control Rheostat Up Switch 1.115,1.75 2.479,2.094 1.365,0.344 10 false Light Control Rheostat Down Switch 4.813,3.323 6.865,3.51 2.052,0.188 10 false Combination Meter Assembly 4.823,3.167 5.281,3.365 0.458,0.198 10 false K20 1.396,2.906 3.448,3.094 2.052,0.188 10 false Trip Switch 2.823,0.625 4.875,0.813 2.052,0.188 10 false K111 2.823,2.5 4.875,2.688 2.052,0.188 10 false K111 3.229,0.625 5.281,0.813 2.052,0.188 10 false K166 3.229,2.5 5.281,2.688 2.052,0.188 10 false K166 3.344,2.292 3.802,2.49 0.458,0.198 10 false 5 3.354,0.417 3.813,0.615 0.458,0.198 10 false 3 0.229,3.375 1.917,3.573 1.688,0.198 10 false *1: for LHD 1.344,3.365 3.031,3.563 1.688,0.198 10 false *2: for RHD 2.906,0.833 3.219,1.031 0.313,0.198 10 false *1 2.906,2.698 3.219,2.896 0.313,0.198 10 false *1 3.313,0.823 3.625,1.021 0.313,0.198 10 false *2 3.313,2.698 3.625,2.896 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:
·

The illumination level of the combination meter assembly can be adjusted by pressing the light control rheostat switch (trip switch).


·

The illumination of the combination meter assembly dims when the taillights are turned on.


·

Setting the illumination to maximum brightness cancels the above dimming of the illumination.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Light Control Switch (UP) Light control rheostat up switch (Trip switch) OFF or ON OFF: Switch released
ON: Switch pushed
-
Light Control Switch (DOWN) Light control rheostat down switch (Trip switch) OFF or ON OFF: Switch released
ON: Switch pushed
-
Body Electrical > Combination Meter > Data List
Tester Display
Light Control Switch (UP)
Light Control Switch (DOWN)
50003 409 398,399
OK:

Light control rheostat up or down switch condition displayed on the GTS changes with the actual switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT TRIP SWITCH
2.INSPECT TRIP SWITCH


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)
a.

Disconnect the K20 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
K111-4 (RV) - K20-2 (TR) Always Below 1 Ω
K111-1 (E) - K20-5 (SW3) Always Below 1 Ω
K111-4 (RV) or K20-2 (TR) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
K166-3 (RV) - K20-2 (TR) Always Below 1 Ω
K166-5 (E) - K20-5 (SW3) Always Below 1 Ω
K166-3 (RV) or K20-2 (TR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR