There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus lines ·
Short in CAN branch lines ·
Central gateway ECU (network gateway ECU) ·
Forward recognition camera (w/ Front Camera System) ·
Millimeter wave radar sensor assembly (w/ Front Camera System) ·
Blind spot monitor sensor RH (w/ Blind Spot Monitor System) ·
Rear television camera assembly (w/ Parking Assist Monitor System or Panoramic View Monitor System) ·
Clearance warning ECU assembly (w/ Parking Support Alert System) ·
Television camera controller (w/ Panoramic View Monitor System) ·
No. 1 CAN junction connector ·
No. 5 CAN junction connector |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A66 No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Millimeter Wave Radar Sensor Assembly
(w/ Front Camera System) |
| *c | to Forward Recognition Camera
(w/ Front Camera System) |
*d | to Central Gateway ECU (Network Gateway ECU) |
| *e | to No. 5 CAN Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A66-1 (CANH) - A66-7 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Millimeter wave radar sensor assembly* |
| A66-2 (CANH) - A66-8 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Forward recognition camera* |
| A66-3 (CANH) - A66-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| A66-5 (CANH) - A66-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 5 CAN junction connector |
*: w/ Front Camera System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 5 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the K76 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-3 (CANH) - A66-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the A66 No. 1 CAN junction connector.
Disconnect the R98 No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to Clearance Warning ECU Assembly
(w/ Parking Support Alert System) |
*d | to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System) |
| *e | to Rear Television Camera Assembly
(w/ Parking Assist Monitor System or Panoramic View Monitor System) |
*f | to No. 1 CAN Junction Connector |
| *g | to Television Camera Controller
(w/ Panoramic View Monitor System) |
- | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R98-1 (CANH) - R98-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| R98-2 (CANH) - R98-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Clearance warning ECU assembly*1 |
| R98-3 (CANH) - R98-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Blind spot monitor sensor RH*2 |
| R98-4 (CANH) - R98-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Rear television camera assembly*3 |
| R98-5 (CANH) - R98-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| R98-8 (CANH) - R98-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Television camera controller*4 |
*1: w/ Parking Support Alert System
*2: w/ Blind Spot Monitor System
*3: w/ Parking Assist Monitor System or Panoramic View Monitor System
*4: w/ Panoramic View Monitor System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 1 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the K76 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R98-1 (CANH) - R98-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K76-23 (CA1H) - K76-8 (CA1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG