Home › Power Source / Network › NETWORKING › NETWORK GATEWAY ECU › from 2021.02
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329711 NETWORK GATEWAY ECU A

NETWORKING  NETWORK GATEWAY ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during central gateway ECU (network gateway ECU) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane tracing assist system (Click here)
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Replacement of certification ECU (smart key ECU assembly) Code registration (Immobiliser function)
·

Wireless door lock control system

·

Entry and start system (for entry function)

·

Entry and start system (for start function)

·

Steering lock function


See Service Bulletin for the registration method.
w/ Parking Support Brake System

Clearance warning ECU assembly


·

Measure ultrasonic sensor detection angle

·

Steering angle zero point learning

·

Register bumper type

·

Register ultrasonic sensor detection angle


·

TOYOTA Parking Assist-sensor System

·

Parking Support Brake System


(Click here)
w/o Parking Support Brake System

Clearance warning ECU assembly


Register bumper type TOYOTA Parking Assist-sensor System (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 55435B 4.REMOVE NO. 1 METER HOOD CLUSTER (for LHD)

Hide 55012A 5.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for LHD)

Hide 55476C 6.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for LHD)

Hide 67913 7.REMOVE FRONT DOOR SCUFF PLATE RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 8.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 9.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)

Hide 55317A 10.REMOVE INSTRUMENT SIDE PANEL RH (for LHD)

Hide 55607 11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 73990 12.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 55303B 13.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/o Passenger Side Knee Airbag)

Hide 55303B 14.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 82877 15.REMOVE ECU INTEGRATION BOX RH (for LHD)

a.

Disconnect each connector.


b.
C380668

Disengage the 2 clamps.


c.

Remove the bolt, nut and ECU integration box RH.


Hide 89111 16.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for LHD)

a.
C380669

Disengage the 2 claws and remove the central gateway ECU (network gateway ECU).

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




Hide 55435B 17.REMOVE NO. 1 METER HOOD CLUSTER (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55434B 18.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 67913 19.REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 20.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 21.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55317A 22.REMOVE INSTRUMENT SIDE PANEL RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55606 23.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55436B 24.REMOVE NO. 2 METER HOOD CLUSTER (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 53601 25.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55302D 26.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD, w/o Driver Side Knee Airbag)

Hide 55302D 27.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD, w/ Driver Side Knee Airbag)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 73900 28.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD, w/ Driver Side Knee Airbag)

Hide 55308B 29.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REMOVAL


Hide 82877 30.REMOVE ECU INTEGRATION BOX RH (for RHD)

a.

Disconnect each connector.


b.
C377921

Disengage the clamp.


c.

Remove the bolt, 2 nuts and ECU integration box RH.


Hide 89111 31.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for RHD)

a.
C377923

Disengage the 2 claws and remove the central gateway ECU (network gateway ECU).

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.