The switch circuit inside the combination meter assembly turns on and off according to the steering pad switch assembly operation.
During test mode, the tire pressure warning light blinks at 0.125 second intervals when "Set Pressure" is selected on the multi-information display, and illuminates when the "OK" switch (steering pad switch assembly) is pressed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C2198 | Initialization Switch Error (for Test Diagnosis) | Test mode procedure is performed. | ·
Steering pad switch assembly ·
Spiral cable sub-assembly ·
Wire harness or connector ·
Tire pressure warning ECU and receiver |
- |
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.
Remove the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL
Inspect the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K22 spiral cable sub-assembly connector.
Disconnect the K21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-10 (+DP2) - K21-28 (MSM+) | Always | Below 1 Ω |
| K22-10 (+DP2) or K21-28 (MSM+) - Body ground | Always | 10 kΩ or higher |
| K22-11 (+DP) - K21-29 (MSTI) | Always | Below 1 Ω |
| K22-11 (+DP) or K21-29 (MSTI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R127 tire pressure warning ECU and receiver connector.
Disconnect the K21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R127-3 (CLSW) - K21-4 (INT) | Always | Below 1 Ω |
| R127-3 (CLSW) or K21-4 (INT) - Body ground | Always | 10 kΩ or higher |
| K21-21 (ES) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the R127 tire pressure warning ECU and receiver connector.
Disconnect the K21 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-4 (INT) - Body ground | Power switch on (IG) | 8 to 15 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG