Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2022.01
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0465299 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C1AAE00  Front Recognition Camera Heater Malfunction  


DESCRIPTION

The forward recognition camera controls the flow of current to the forward recognition hood.

If the forward recognition camera detects a malfunction in the forward recognition hood circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE00 Front Recognition Camera Heater Malfunction
Either of the following conditions is met after 10 seconds have elapsed since the power switch was turned on (IG):
·

Short to +B detected in the forward recognition hood circuit for 1 second or more cumulatively

·

Open or short to ground detected in the forward recognition hood circuit for 5 seconds or more


·

Forward recognition hood

·

Forward recognition camera

·

Harness or connector



WIRING DIAGRAM

E444861E31
0.333,0.688 2.323,0.885 1.99,0.198 10 false from IG1-NO. 1 Relay 2.302,0.875 4.135,1.073 1.833,0.198 10 false ECU-IG1 NO. 3 3.406,1.229 5.167,1.646 1.76,0.417 10 false Forward Recognition Hood 3.406,0.573 3.563,0.771 0.156,0.198 10 false 1 3.604,0.563 4.063,0.76 0.458,0.198 10 false IG1 3.396,1.063 3.854,1.26 0.458,0.198 10 false V16 4.531,0.563 4.99,0.76 0.458,0.198 10 false HTR 4.906,0.573 5.063,0.771 0.156,0.198 10 false 2 5.729,0.698 6.188,0.896 0.458,0.198 10 false HTR 5.552,0.573 5.708,0.771 0.156,0.198 10 false 1 5.271,2.021 5.646,2.229 0.375,0.208 10 false V24 5.26,2.188 7.052,2.542 1.792,0.354 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CHECK FOR DTCs
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 430

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

B

2.INSPECT FORWARD RECOGNITION HOOD
2.INSPECT FORWARD RECOGNITION HOOD
a.

Turn the power switch off.


b.
C367122C26
1.51,0.188 1.938,0.438 0.427,0.25 1.49,1.833 1.625,1.24 true 1.948,1.813 1.802,1.229 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.604,0.24 2.063,0.438 0.458,0.198 10 false V16 1.313,1.865 1.771,2.063 0.458,0.198 10 false HTR 1.885,1.865 2.344,2.063 0.458,0.198 10 false IG1
*a Component without harness connected
(Forward Recognition Hood)


Disconnect the forward recognition hood connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V16-1 (IG1) - V16-2 (HTR) Always 28.5 to 31.5 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPLACE FORWARD RECOGNITION HOOD

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
C367313C45
1.552,0.208 1.938,0.448 0.385,0.24 1.115,0.979 1.281,0.979 1.281,0.979 1.594,1.229 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.625,0.26 2.083,0.458 0.458,0.198 10 false V16 0.896,0.917 1.354,1.115 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Forward Recognition Hood)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V16-1 (IG1) - Body ground Power switch ON 8 to 16 V
Power switch off Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION HOOD - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION HOOD - FORWARD RECOGNITION CAMERA)
a.

Disconnect the V24 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V16-2 (HTR) - V24-1 (HTR) Always Below 1 Ω
V16-2 (HTR) or V24-1 (HTR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR