Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › from 2022.01
RM33C0E _59 Vehicle Exterior _065470 MIRROR (EXT) _0332577 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch  


DESCRIPTION

The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (front passenger door) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (front passenger door) operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly (front passenger door), to adjust the mirror surface position.

WIRING DIAGRAM

for LHD


B490272E69
1.031,0.656 1.635,0.948 0.604,0.292 10 false M+ 0.896,1.26 1.5,1.552 0.604,0.292 10 false MSW 1.135,1.833 1.74,2.125 0.604,0.292 10 false E 0.156,2.448 0.76,2.74 0.604,0.292 10 false O26 0.167,2.594 1.375,2.979 1.208,0.385 10 false Outer Mirror Switch Assembly 0.531,3.354 2.479,3.635 1.948,0.281 10 false : CAN Communication Line 1.729,2.427 2.333,2.719 0.604,0.292 10 false K53 1.729,2.583 3.365,3.031 1.635,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 3.625,2.427 4.229,2.719 0.604,0.292 10 false N10 3.625,2.583 5.052,3.198 1.427,0.615 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 5.396,2.427 6.417,2.771 1.021,0.344 10 false N17*1, N24*2 5.385,2.583 6.844,3.135 1.458,0.552 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 5.281,0.844 6.75,1.208 1.469,0.365 10 false Horizontal Mirror Motor 5.281,0.552 5.885,0.844 0.604,0.292 10 false MH 5.302,1.729 5.906,2.021 0.604,0.292 10 false MV 5.104,0.563 5.708,0.854 0.604,0.292 10 false 9 4.948,1.052 5.552,1.344 0.604,0.292 10 false 10*1 4.99,1.635 5.594,1.927 0.604,0.292 10 false 1*1 4.708,1.719 5.313,2.01 0.604,0.292 10 false 1 4.688,1.156 5.292,1.448 0.604,0.292 10 false 10 4.719,0.573 5.323,0.865 0.604,0.292 10 false 9 4.208,0.667 4.813,0.958 0.604,0.292 10 false RMHR 2,0.677 2.604,0.969 0.604,0.292 10 false MIRB 5.313,1.156 5.917,1.448 0.604,0.292 10 false M+ 1.823,0.552 2.427,0.844 0.604,0.292 10 false 7 1.823,1.156 2.427,1.448 0.604,0.292 10 false 8 1.823,1.719 2.427,2.01 0.604,0.292 10 false 9 1.354,1.729 1.958,2.021 0.604,0.292 10 false 7 1.365,1.156 1.969,1.448 0.604,0.292 10 false 5 1.385,0.552 1.99,0.844 0.604,0.292 10 false 4 2,1.271 2.604,1.563 0.604,0.292 10 false MIRS 2.01,1.854 2.615,2.146 0.604,0.292 10 false MIRE 4.208,1.26 4.813,1.552 0.604,0.292 10 false RM+R 4.198,1.833 4.802,2.125 0.604,0.292 10 false RMVR 5.354,2.031 6.823,2.396 1.469,0.365 10 false Vertical Mirror Motor 5.021,1.188 5.625,1.479 0.604,0.292 10 false 8*2 5,1.771 5.604,2.063 0.604,0.292 10 false 7*2 2.406,3.5 4.354,3.781 1.948,0.281 10 false *1: for 16 Pin Connector 4.198,3.5 6.146,3.781 1.948,0.281 10 false *2: for 22 Pin Connector


for RHD


B490272E70
1.031,0.656 1.635,0.948 0.604,0.292 10 false M+ 0.896,1.26 1.5,1.552 0.604,0.292 10 false MSW 1.135,1.833 1.74,2.125 0.604,0.292 10 false E 0.167,2.427 0.771,2.719 0.604,0.292 10 false N26 0.167,2.583 1.375,2.969 1.208,0.385 10 false Outer Mirror Switch Assembly 0.531,3.354 2.479,3.635 1.948,0.281 10 false : CAN Communication Line 1.729,2.427 2.333,2.719 0.604,0.292 10 false K53 1.729,2.583 3.365,3.031 1.635,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 3.625,2.427 4.229,2.719 0.604,0.292 10 false O9 3.625,2.583 5.052,3.198 1.427,0.615 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 5.396,2.427 6.719,2.76 1.323,0.333 10 false O22 5.385,2.583 6.844,3.135 1.458,0.552 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 5.385,2.042 6.854,2.406 1.469,0.365 10 false Vertical Mirror Motor 5.281,0.552 5.885,0.844 0.604,0.292 10 false MH 5.302,1.729 5.906,2.021 0.604,0.292 10 false MV 5.115,0.563 5.719,0.854 0.604,0.292 10 false 9 4.708,1.719 5.313,2.01 0.604,0.292 10 false 1 4.688,1.156 5.292,1.448 0.604,0.292 10 false 10 4.719,0.573 5.323,0.865 0.604,0.292 10 false 9 4.208,0.667 4.813,0.958 0.604,0.292 10 false LMHR 2,0.677 2.604,0.969 0.604,0.292 10 false MIRB 5.313,1.156 5.917,1.448 0.604,0.292 10 false M+ 1.823,0.552 2.427,0.844 0.604,0.292 10 false 7 1.823,1.156 2.427,1.448 0.604,0.292 10 false 8 1.823,1.719 2.427,2.01 0.604,0.292 10 false 9 1.365,1.729 1.969,2.021 0.604,0.292 10 false 7 1.365,1.156 1.969,1.448 0.604,0.292 10 false 5 1.365,0.552 1.969,0.844 0.604,0.292 10 false 4 2,1.271 2.604,1.563 0.604,0.292 10 false MIRS 2.01,1.854 2.615,2.146 0.604,0.292 10 false MIRE 4.208,1.26 4.813,1.552 0.604,0.292 10 false LM+R 4.198,1.833 4.802,2.125 0.604,0.292 10 false LMVR 5.271,0.865 6.74,1.229 1.469,0.365 10 false Horizontal Mirror Motor 5.115,1.198 5.719,1.49 0.604,0.292 10 false 8 5.135,1.771 5.74,2.063 0.604,0.292 10 false 7


CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system and LIN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror OFF or ON OFF: Mirror select switch off
ON: Mirror select switch R switch on
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror OFF or ON OFF: Mirror select switch off
ON: Mirror select switch L switch on
-
Mirror Position SW (R) Mirror adjust switch signal (Right) OFF or ON OFF: Mirror adjust switch not pushed right
ON: Mirror adjust switch pushed right
Check with the mirror select switch L or R selected
Mirror Position SW (L) Mirror adjust switch signal (Left) OFF or ON OFF: Mirror adjust switch not pushed left
ON: Mirror adjust switch pushed left
Check with the mirror select switch L or R selected
Mirror Position SW (Up) Mirror adjust switch signal (Up) OFF or ON OFF: Mirror adjust switch not pushed up
ON: Mirror adjust switch pushed up
Check with the mirror select switch L or R selected
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) OFF or ON OFF: Mirror adjust switch not pushed down
ON: Mirror adjust switch pushed down
Check with the mirror select switch L or R selected
Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (R)
Mirror Selection SW (L)
Mirror Position SW (R)
Mirror Position SW (L)
Mirror Position SW (Up)
Mirror Position SW (Dwn)
50003 123 98,99,100,101,102,103
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (MIRROR SURFACE)

NG

4.INSPECT OUTER MIRROR SWITCH ASSEMBLY
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (MIRROR SURFACE)
a.

Remove the outer rear view mirror assembly (front passenger door).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly (front passenger door) (mirror surface).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) - OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR))

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) - OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR))
a.

for LHD:

i.

Disconnect the N17*1 or N24*2 outer rear view mirror assembly (front passenger door).

*1: for 16 Pin Connector

*2: for 22 Pin Connector



ii.

Disconnect the N10 outer mirror control ECU assembly (front passenger door).


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 16 Pin Connector
Tester Connection Condition Specified Condition
N17-1 (MV) - N10-1 (RMVR) Always Below 1 Ω
N17-9 (MH) - N10-9 (RMHR) Always Below 1 Ω
N17-10 (M+) - N10-10 (RM+R) Always Below 1 Ω
N17-1 (MV) or N10-1 (RMVR) - Body ground Always 10 kΩ or higher
N17-9 (MH) or N10-9 (RMHR) - Body ground Always 10 kΩ or higher
N17-10 (M+) or N10-10 (RM+R) - Body ground Always 10 kΩ or higher

for 22 Pin Connector
Tester Connection Condition Specified Condition
N24-7 (MV) - N10-1 (RMVR) Always Below 1 Ω
N24-9 (MH) - N10-9 (RMHR) Always Below 1 Ω
N24-8 (M+) - N10-10 (RM+R) Always Below 1 Ω
N24-7 (MV) or N10-1 (RMVR) - Body ground Always 10 kΩ or higher
N24-9 (MH) or N10-9 (RMHR) - Body ground Always 10 kΩ or higher
N24-8 (M+) or N10-10 (RM+R) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the O22 outer rear view mirror assembly (front passenger door).


ii.

Disconnect the O9 outer mirror control ECU assembly (front passenger door).


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O22-7 (MV) - O9-1 (LMVR) Always Below 1 Ω
O22-9 (MH) - O9-9 (LMHR) Always Below 1 Ω
O22-8 (M+) - O9-10 (LM+R) Always Below 1 Ω
O22-7 (MV) or O9-1 (LMVR) - Body ground Always 10 kΩ or higher
O22-9 (MH) or O9-9 (LMHR) - Body ground Always 10 kΩ or higher
O22-8 (M+) or O9-10 (LM+R) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the O26*1 or N26*2 outer mirror switch assembly.

*1: for LHD

*2: for RHD



b.

Disconnect the K53 main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
O26-7 (E) - K53-9 (MIRE) Always Below 1 Ω
O26-4 (M+) - K53-7 (MIRB) Always Below 1 Ω
O26-5 (MSW) - K53-8 (MIRS) Always Below 1 Ω
O26-7 (E) or K53-9 (MIRE) - Body ground Always 10 kΩ or higher
O26-4 (M+) or K53-7 (MIRB) - Body ground Always 10 kΩ or higher
O26-5 (MSW) or K53-8 (MIRS) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
N26-7 (E) - K53-9 (MIRE) Always Below 1 Ω
N26-4 (M+) - K53-7 (MIRB) Always Below 1 Ω
N26-5 (MSW) - K53-8 (MIRS) Always Below 1 Ω
N26-7 (E) or K53-9 (MIRE) - Body ground Always 10 kΩ or higher
N26-4 (M+) or K53-7 (MIRB) - Body ground Always 10 kΩ or higher
N26-5 (MSW) or K53-8 (MIRS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR