Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › ELECTRONIC CONTROLLED CARBURETOR SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355837 ELECTRONIC CONTROLLED CARBURETOR SYSTEM C

1BZ-FPE ENGINE CONTROL  ELECTRONIC CONTROLLED CARBURETOR SYSTEM  P0136  Oxygen Sensor Circuit (Bank 1 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. To help the ECM to deliver accurate air-fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A088111E52
1.292,2.26 1.073,2.26 false 3.094,0.646 3.26,0.646 false 2.521,0.021 3.792,0.25 1.271,0.229 10 false Atmospheric Air 3.292,0.552 3.938,0.75 0.646,0.198 10 false Housing 3.292,1.5 4.5,1.698 1.208,0.198 10 false Platinum Electrode 3.292,1.76 3.823,1.958 0.531,0.198 10 false Heater 3.292,2.021 4.458,2.219 1.167,0.198 10 false Coating (Ceramic) 1.927,2.51 2.792,2.708 0.865,0.198 10 false Exhaust Gas 1.344,2.177 1.771,2.375 0.427,0.198 10 false Cover 5.458,0.104 6.865,0.302 1.406,0.198 10 false Ideal Air Fuel Mixture 4.708,2.26 6.667,2.427 1.958,0.167 10 false Richer - Air Fuel Ratio - Leaner 4.354,0.281 5.313,0.479 0.958,0.198 10 false Output Voltage 3.25,1.052 4.385,1.417 1.135,0.365 10 false Solid Electrolyte (Zirconia Element)

DTC No. DTC Detecting Condition Trouble Area
P0136/27 While vehicle driving with warmed engine, heated oxygen sensor (bank 1 sensor 2) output does not switch from RICH to LEAN or from LEAN to RICH.
(2 trip detection logic)
·

Open or short in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

ECM



WIRING DIAGRAM

A403046E02
0.344,0.333 0.5,0.531 0.156,0.198 10 false 6 0.542,0.333 0.875,0.5 0.333,0.167 10 false AM1 1.313,0.344 1.604,0.521 0.292,0.177 10 false IG1 1.646,0.323 1.802,0.521 0.156,0.198 10 false 5 1.948,0.24 2.104,0.438 0.156,0.198 10 false 6 1.917,0.438 2.198,0.635 0.281,0.198 10 false 2C 0.594,0.823 0.927,1.01 0.333,0.188 10 false J63 0.594,0.99 1.49,1.208 0.896,0.219 10 false Ignition SW 0.354,1.531 0.729,1.74 0.375,0.208 10 false AM1 0.354,2.156 1.073,2.385 0.719,0.229 10 false J/B ALT 0.354,2.74 0.771,2.969 0.417,0.229 10 false ALT 0.365,3.552 1.229,3.75 0.865,0.198 10 false R/B NO. 2-B 1.302,3.552 1.635,3.823 0.333,0.271 10 false P/I 1.938,3.188 2.094,3.385 0.156,0.198 10 false 1 1.917,3.396 2.188,3.594 0.271,0.198 10 false 2E 1.948,3.635 2.104,3.833 0.156,0.198 10 false 3 1.917,3.823 2.156,4.031 0.24,0.208 10 false 2D 2.438,3.552 3.083,3.75 0.646,0.198 10 false EFI-MAIN 3.323,4.125 3.656,4.313 0.333,0.188 10 false EFI 4.052,3.594 4.208,3.792 0.156,0.198 10 false 2 4.031,0.198 4.219,0.396 0.188,0.198 10 false 7 4,3.823 4.292,4.052 0.292,0.229 10 false 2D 2.365,4.406 3.865,4.646 1.5,0.24 10 false NO. 2 Integration Relay 3.99,0.438 4.26,0.646 0.271,0.208 10 false 2C 4.042,0.656 4.219,0.833 0.177,0.177 10 false 8 3.99,0.865 4.281,1.094 0.292,0.229 10 false 2C 4.042,1.313 4.219,1.521 0.177,0.208 10 false 4 4,1.531 4.271,1.75 0.271,0.219 10 false 2D 3.271,1.229 3.594,1.427 0.323,0.198 10 false IG2 2.385,1.01 3.042,1.24 0.656,0.229 10 false IG2 NO. 1 4.469,1.417 4.635,1.604 0.167,0.188 10 false 2 4.646,1.417 4.875,1.615 0.229,0.198 10 false +B 5.042,1.417 5.458,1.615 0.417,0.198 10 false HT1B 5.479,1.406 5.667,1.604 0.188,0.198 10 false 1 4.604,1.01 5.354,1.198 0.75,0.188 10 false IGN NO. 1 5.906,1.323 6.135,1.521 0.229,0.198 10 false 1 5.844,1.531 6.167,1.74 0.323,0.208 10 false B76 6.208,1.406 6.646,1.594 0.438,0.188 10 false HT1B 6.198,2.198 6.677,2.385 0.479,0.188 10 false OX1B 5.875,2.094 6.063,2.292 0.188,0.198 10 false 13 5.844,2.292 6.208,2.49 0.365,0.198 10 false B77 5.573,2 5.76,2.198 0.188,0.198 10 false * 5.438,2.208 5.625,2.406 0.188,0.198 10 false 3 5.01,2.167 5.448,2.333 0.438,0.167 10 false OX1B 4.635,2.198 4.854,2.396 0.219,0.198 10 false E2 4.469,2.188 4.656,2.385 0.188,0.198 10 false 4 4.5,2.635 4.833,2.813 0.333,0.177 10 false A62 4.49,2.802 5.469,3.156 0.979,0.354 10 false Heated Oxygen Sensor 5.917,3.229 6.104,3.427 0.188,0.198 10 false 9 5.844,3.417 6.177,3.615 0.333,0.198 10 false B77 6.208,3.302 6.458,3.49 0.25,0.188 10 false E2 5.917,3.635 6.104,3.833 0.188,0.198 10 false 2 5.844,3.813 6.156,4.01 0.313,0.198 10 false A51 6.188,3.802 6.688,4.01 0.5,0.208 10 false MREL 5.823,4.604 6.01,4.802 0.188,0.198 10 false 2 5.281,4.604 5.469,4.802 0.188,0.198 10 false 3 5.292,5.49 5.479,5.688 0.188,0.198 10 false 4 5.813,5.479 6,5.677 0.188,0.198 10 false 1 4.625,4.781 5.146,5.469 0.521,0.688 10 false ENG STOP/P LOCK NO. 2 3.76,6.021 3.948,6.219 0.188,0.198 10 false 3 6.219,7.021 7.021,7.24 0.802,0.219 10 false Engine ECU 4.5,7.156 5.417,7.385 0.917,0.229 10 false *: Shielded 3.542,6.021 3.729,6.219 0.188,0.198 10 false R 2.656,6.021 2.844,6.219 0.188,0.198 10 false E 2.458,6.021 2.646,6.219 0.188,0.198 10 false 4 2.583,6.5 2.958,6.698 0.375,0.198 10 false A14 2.583,6.677 3.927,6.906 1.344,0.229 10 false Engine Stop Switch 0.344,6.073 1.094,6.281 0.75,0.208 10 false FL MAIN 0.51,6.76 1.26,6.99 0.75,0.229 10 false Battery

CONFIRMATION DRIVING PATTERN

A128472E05
0.598,0.696 1.548,0.859 0.95,0.163 10 Vehicle Speed 0.421,1.65 1.546,1.813 1.125,0.163 10 Ignition Switch off 0.894,2.168 1.564,2.331 0.67,0.163 10 (a) to (e) 0.444,1.182 1.607,1.402 1.163,0.22 10 40 km/h (29 mph) 1.643,1.746 1.256,2.141 false 1.693,2.047 2.448,2.356 0.755,0.309 10 60 seconds or more 2.785,2.047 3.541,2.356 0.755,0.309 10 10 seconds or more 3.696,2.047 4.451,2.356 0.755,0.309 10 10 seconds or more 5.022,2.047 5.778,2.356 0.755,0.309 10 10 seconds or more 5.798,1.824 6.197,1.995 0.4,0.17 10 Time 2.051,0.436 3.186,0.745 1.135,0.309 10 Once 40 seconds or more 3.208,0.436 4.342,0.745 1.135,0.309 10 Twice 40 seconds or more 4.541,0.436 6.064,0.745 1.523,0.309 10 Ten times 40 seconds or more 5.308,1.522 5.52,1.685 0.212,0.163 10 (h) 4.864,1.272 5.075,1.435 0.212,0.163 10 (g) 3.989,1.536 4.201,1.699 0.212,0.163 10 (h) 1.698,1.464 2.075,1.627 0.377,0.163 10 Idling 2.107,1.464 2.319,1.627 0.212,0.163 10 (f) 2.605,1.272 2.817,1.435 0.212,0.163 10 (g) 3.063,1.536 3.274,1.699 0.212,0.163 10 (h) 3.52,1.272 3.732,1.435 0.212,0.163 10 (g)

HINT:

This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.


(a) Connect an intelligent tester to the DLC3.

(b) Turn the ignition switch on (IG) and turn the tester on.

(c) Clear DTCs.

(d) Switch the ECM from normal mode to check mode.

(e) Start the engine.

(f) Allow the engine to idle for 60 seconds.

(g) Drive the vehicle at a vehicle speed of more than 40 km/h (29 mph) for 40 seconds or more.

(h) Allow the engine to idle for 10 seconds or more.

(i) Repeat steps (g) and (h) described above at least 10 times.


NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.


CAUTION / NOTICE / HINT

HINT:

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.


HINT:

Intelligent tester only:

Malfunctioning areas can be identified by performing the A/F Control function provided in the Active Test. The A/F Control function can help to determine whether the heated oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the A/F control operation using an intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the intelligent tester ON.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / A/F Control.

5.

Perform the A/F Control operation with the engine in an idling condition (press the right or left button to change the fuel injection volume).

6.

Monitor the output voltage of the heated oxygen sensor displayed on the tester.



HINT:
·

The A/F Control operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
O2S B1 S2
(HO2)
+ 25% Rich More than 0.2 V
O2S B1 S2
(HO2)
- 12.5% Lean Less than 0.1 V


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0136)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester ON.


c.

Select the following menu items: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result:
Display (DTC Output) Proceed To
P0136 A
P0136 and other DTCs B


HINT:

If any DTCs other than P0136 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester ON.


c.

Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1 S2.


d.

Allow the engine to run at 2500 rpm for 3 minutes.


e.

Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.

Standard voltage:

The heated oxygen sensor voltage alternates between below 0.45 V and 0.6 V or more.



A128474E13
1.458,0.51 1.771,0.708 0.313,0.198 10 false 1 V 2.521,0.24 2.854,0.448 0.333,0.208 10 false OK 3.469,0.24 3.771,0.427 0.302,0.188 10 false NG 4.406,0.24 4.708,0.427 0.302,0.188 10 false NG 5.354,0.24 5.656,0.427 0.302,0.188 10 false NG 1.365,0.781 1.823,0.979 0.458,0.198 10 false 0.6 V 1.281,1.083 1.792,1.271 0.51,0.188 10 false 0.45 V 1.458,1.375 1.781,1.583 0.323,0.208 10 false 0 V

Result:
Proceed to
OK
NG



OK

3.CONFIRMATION DRIVING PATTERN

NG

5.INSPECT HEATED OXYGEN SENSOR
3.CONFIRMATION DRIVING PATTERN
HINT:

Clear all DTCs before performing the confirmation driving pattern.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OUTPUT AGAIN)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OUTPUT AGAIN)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester ON.


c.

Select the following menu items: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.


Result:
Display (DTC Output) Proceed To
No output A
P0136 B



A

B

5.INSPECT HEATED OXYGEN SENSOR
A062378E55
1.438,1.406 1.177,1.885 false 1.969,1.375 2.208,1.885 false 1.438,0.823 1.552,1.021 0.115,0.198 10 false 2 1.865,0.823 1.979,1.021 0.115,0.198 10 false 1 1.438,1.229 1.552,1.427 0.115,0.198 10 false 4 1.865,1.229 1.979,1.427 0.115,0.198 10 false 3 2.281,0.271 2.76,0.469 0.479,0.198 10 false HT1B 0.948,0.292 1.25,0.521 0.302,0.229 10 false +B 2.281,1.844 2.719,2.042 0.438,0.198 10 false OX1B 0.927,1.844 1.146,2.042 0.219,0.198 10 false E2

a.

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance of the sensor.

Standard resistance:
Tester Connection Condition Specified Condition
1 (HT1B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT1B) - 4 (E2) Always 10 kΩ or higher



c.

Reconnect the heated oxygen sensor connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - EFI MAIN RELAY)

NG

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - EFI MAIN RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the NO. 2 integration relay from the relay block No.2.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A62-2 (+B) - 2D-4 Always Below 1Ω
A62-2 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor connector.


e.

Reinstall the NO. 2 integration relay.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
B77-13 (OX1B) - A62-3 (OX1B) Always Below 1Ω
B77-9 (E2) - A62-4 (E2) Always Below 1Ω
B77-13 (OX1B) or A62-3 (OX1B) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the heated oxygen sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR