Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › ELECTRONIC CONTROLLED CARBURETOR SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355837 ELECTRONIC CONTROLLED CARBURETOR SYSTEM C

1BZ-FPE ENGINE CONTROL  ELECTRONIC CONTROLLED CARBURETOR SYSTEM  P1300  Igniter Circuit Malfunction (No. 1)  


DESCRIPTION

The engine ECU determines the ignition timing, turns ON Tr1 at a predetermined angle (°CA) before the desired ignition timing and outputs an ignition signal (IGT) "1" to the igniter.

Since the width of the IGT signal is constant, the dwell angle control circuit in the igniter determines the time the control circuit starts, primary current flow to the ignition coil based on the engine speed and ignition timing of the previous revolution that is, the time the Tr2 turns ON.

When it reaches the ignition timing, the engine ECU turns Tr1 OFF and outputs the IGT signal "0".

This turns Tr2 OFF, interrupting the primary current flow and generating a high voltage in the secondary coil which causes the spark plug to spark. Also, the counter electromotive force is generated when the primary current is interrupted, and the igniter sends an ignition confirmation signal (IGF) to the engine ECU.

The engine ECU stops fuel injection as a fail safe function when the IGF signal is not input to the engine ECU.

DTC No. DTC Detection Condition Suspected Area
P1300/14 No IGF signal to engine ECU for 4 consecutive IGT signal
·

Open or short in IGF or IGT circuit from igniter to engine ECU

·

Igniter

·

Engine ECU



WIRING DIAGRAM

A403039E01
1.167,1.135 1.354,1.354 0.188,0.219 10 false 6 1.365,1.135 1.708,1.365 0.344,0.229 10 false AM1 2.177,1.135 2.5,1.365 0.323,0.229 10 false IG1 2.479,1.125 2.667,1.344 0.188,0.219 10 false 5 1.5,1.615 1.792,1.802 0.292,0.188 10 false J63 1.5,1.781 2.354,2.021 0.854,0.24 10 false Ignition SW 0.344,2.104 0.729,2.333 0.385,0.229 10 false AM1 0.333,3.135 1.031,3.375 0.698,0.24 10 false J/B ALT 0.344,4.188 0.74,4.406 0.396,0.219 10 false ALT 0.51,5.635 1.427,5.844 0.917,0.208 10 false R/B NO. 2-B 1.906,5.635 2.219,5.854 0.313,0.219 10 false P/I 3.521,1.031 3.708,1.25 0.188,0.219 10 false 6 3.479,1.24 3.76,1.458 0.281,0.219 10 false 2C 3.531,1.479 3.719,1.698 0.188,0.219 10 false 1 3.49,1.667 3.74,1.896 0.25,0.229 10 false 2E 3.875,1.813 4.667,2.021 0.792,0.208 10 false IG2 NO. 1 4.792,2 5.167,2.208 0.375,0.208 10 false IG2 4.052,2.344 5.708,2.552 1.656,0.208 10 false NO. 2 Integration Relay 5.75,1.042 5.99,1.271 0.24,0.229 10 false 7 5.719,1.25 5.979,1.448 0.26,0.198 10 false 2C 5.76,1.479 6.01,1.667 0.25,0.188 10 false 8 5.719,1.667 6,1.906 0.281,0.24 10 false 2C 4.396,2.969 4.729,3.146 0.333,0.177 10 false INJ 5.823,3.74 6.25,3.958 0.427,0.219 10 false IGT 5.823,3.99 6.198,4.219 0.375,0.229 10 false IGF 5.594,3.615 5.781,3.833 0.188,0.219 10 false 6 5.604,3.865 5.792,4.083 0.188,0.219 10 false 3 5.01,3.604 5.198,3.823 0.188,0.219 10 false 2 5.01,3.865 5.198,4.083 0.188,0.219 10 false 1 5.021,4.125 5.208,4.344 0.188,0.219 10 false 5 4.677,3.74 5.01,3.927 0.333,0.188 10 false IGT 4.688,3.99 5.042,4.208 0.354,0.219 10 false IGF 4.729,4.219 5.01,4.448 0.281,0.229 10 false C- 3.667,4.219 3.979,4.438 0.313,0.219 10 false IG4 3.656,3.74 3.958,3.958 0.302,0.219 10 false +B 3.438,3.615 3.667,3.802 0.229,0.188 10 false 3 3.448,4.094 3.635,4.302 0.188,0.208 10 false 4 4.083,4.708 4.438,4.917 0.354,0.208 10 false B34 4.083,4.875 4.552,5.115 0.469,0.24 10 false Igniter 3.448,6.115 3.635,6.333 0.188,0.219 10 false 1 3.677,6.365 4.031,6.573 0.354,0.208 10 false IG+ 4.719,6.917 4.948,7.146 0.229,0.229 10 false C- 5.01,6.906 5.198,7.125 0.188,0.219 10 false 2 2.667,7.021 3.021,7.24 0.354,0.219 10 false B39 2.677,7.188 3.552,7.396 0.875,0.208 10 false Ignition Coil 3.531,7.625 4.24,7.823 0.708,0.198 10 false Distributor 5.99,8.094 6.375,8.313 0.385,0.219 10 false B76 6,8.26 6.833,8.479 0.833,0.219 10 false Engine ECU 0.448,7.552 1.031,7.781 0.583,0.229 10 false Battery 0.323,6.406 0.958,6.635 0.635,0.229 10 false FL MAIN 3.406,5.531 4.615,5.813 1.208,0.281 10 false Check Connector

PROCEDURE

1.Check spark plug and spark.

OK

2.Check for open and short in harness and connector in IGF signal circuit between engine ECU and igniter.

NG

4.Check for open and short in harness and connector in IGT signal circuit between engine ECU and igniter.
2.Check for open and short in harness and connector in IGF signal circuit between engine ECU and igniter.

OK

3.Disconnect igniter connector and check voltage between terminal IGF of engine ECU connector and body ground.

NG

Repair or replace harness or connector.

3.Disconnect igniter connector and check voltage between terminal IGF of engine ECU connector and body ground.
A401591E01
1.208,0.906 1.542,0.385 true 0.552,0.188 0.865,0.385 0.313,0.198 10 false ON 1.479,0.198 1.833,0.406 0.354,0.208 10 false IGF 0.875,1.833 1.229,2.042 0.354,0.208 10 false (+) 1.594,1.833 1.802,2.073 0.208,0.24 10 false (-)

PREPARATION:

a.

Disconnect the igniter connector.


b.

Remove the side trim bracket.


c.

Turn the ignition switch ON.


CHECK:

Measure the voltage between terminal IGF of the engine ECU connector and body ground.

OK:

Voltage: 4.5 - 5.5 V


Result:
Proceed to
OK
NG



OK

NG

Replace igniter.

4.Check for open and short in harness and connector in IGT signal circuit between engine ECU and igniter.

OK

5.Check voltage between terminal IGT of engine ECU connector and body ground.

NG

Repair or replace harness or connector.

5.Check voltage between terminal IGT of engine ECU connector and body ground.
A401592E01
0.969,0.917 1.5,0.396 true 0.583,0.208 1.125,0.406 0.542,0.198 10 false START 1.427,0.208 1.75,0.396 0.323,0.188 10 false IGT 0.615,1.854 0.865,2.115 0.25,0.26 10 false (+) 1.365,1.844 1.604,2.042 0.24,0.198 10 false (-)

A401593E01
0.063,0.042 2.063,0.292 2,0.25 10 false IGT and IGF Signal Waveforms 2.792,0.146 3.302,0.5 0.51,0.354 10 false 2 V/ Division 0.052,0.76 0.365,0.958 0.313,0.198 10 false IGT 0.375,1.042 0.688,1.24 0.313,0.198 10 false 0 V 0.375,1.563 0.688,1.76 0.313,0.198 10 false 0 V 0.052,1.26 0.365,1.458 0.313,0.198 10 false IGF 0.948,1.885 2.563,2.104 1.615,0.219 10 false 10 msec./Division (Idling)

PREPARATION:

Remove the side trim bracket.

CHECK:

Measure the voltage between terminal IGT of the engine ECU connector and body ground when the engine is cranked.

OK:

Voltage: More than 0.1 V and less than 4.5 V


Reference:

INSPECTION USING OSCILLOSCOPE


During idling, check the waveforms between terminals IGT and E1, and IGF and E1 of the engine ECU connector.

HINT:

The correct waveforms are as shown.


Result:
Proceed to
OK
NG



OK

6.Disconnect igniter connector, and check voltage between terminals IGT of engine ECU connector and body ground.

NG

6.Disconnect igniter connector, and check voltage between terminals IGT of engine ECU connector and body ground.
A401592E01
0.969,0.917 1.5,0.396 true 0.583,0.208 1.125,0.406 0.542,0.198 10 false START 1.427,0.208 1.75,0.396 0.323,0.188 10 false IGT 0.615,1.854 0.865,2.115 0.25,0.26 10 false (+) 1.365,1.844 1.604,2.042 0.24,0.198 10 false (-)

PREPARATION:

a.

Disconnect the igniter connector.


b.

Remove the side trim bracket.


CHECK:

Measure the voltage between terminal IGT of the engine ECU connector and body ground when the engine is cranked.

OK:

Voltage: More than 0.1 V and less than 5V


Result:
Proceed to
OK
NG



OK

7.Check voltage between terminal 3 of igniter connector and body ground.

NG

Replace igniter.

7.Check voltage between terminal 3 of igniter connector and body ground.
A401594E01
2.448,1.344 1.979,0.698 true 0.573,0.073 0.885,0.271 0.313,0.198 10 false ON 0.49,0.646 1.031,0.844 0.542,0.198 10 false START 0.99,1.552 1.302,1.75 0.313,0.198 10 false (-) 1.646,1.542 1.958,1.74 0.313,0.198 10 false (+) 2.438,1.406 2.75,1.604 0.313,0.198 10 false 3

PREPARATION:

Disconnect the igniter connector.

CHECK:

Measure the voltage between terminal 3 of the igniter connector and body ground when the ignition switch is turned ON and START position.

OK:

Voltage: 9 - 14 V


Result:
Proceed to
OK
NG



OK

8.Check for for open and short in harness and connector between ignition switch and igniter.

NG

Check and repair igniter power source circuit.

8.Check for for open and short in harness and connector between ignition switch and igniter.

OK

Replace igniter.

NG

Repair or replace harness or connector.