Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM M

N04C-UH ENGINE CONTROL  ECD SYSTEM  REGISTRATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When an injector assembly is replaced, the injector's compensation code must be input into the ECM.

·

When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.



PROCEDURE

Hide 1.INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

NOTICE:
·

Injector compensation codes are printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

Although some injectors are marked with a 32-digit alphanumeric value, only the first 30-digits must to be input.



a.
A288762E10
2.344,1.688 2.552,0.76 true 0.094,0.052 1.323,0.25 1.229,0.198 10 false *a 2.281,1.75 2.917,2.052 0.635,0.302 10 false *b

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.

NOTICE:

Do not start the engine.


HINT:

The injector compensation code is imprinted on the head portion of each injector assembly


Text in Illustration
*a Example
*b Injector Compensation Code


d.
A321636

Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.


e.

Press "Next".


f.
A321637

Press "Next" again to proceed.


g.
A321638

Select "Set Compensation Code".


h.

Press "Next".


i.
A321639

Select the number of the cylinder corresponding to the injector compensation code that you want to register.


j.

Press "Next".


k.
A321640

Register the compensation code.

i.

Press "Input".


ii.

Manually input the cylinder's compensation code using the keyboard on the tester screen. The code is imprinted on the injector's head portion.

NOTICE:

Although some injectors are marked with a 32-digit alphanumeric value, only the first 30-digits must to be input.


HINT:

Each injector compensation code is unique.

The correct compensation code must be input into each cylinder selected on the tester.



iii.

Confirm that the compensation code is correct for the selected cylinder, and then press "OK".



l.
A321642

Check that the compensation code displayed on the screen is correct, by comparing it with the compensation code on the head portion of the injector.

NOTICE:

If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:
·

If a wrong compensation code was input, return to the "Input Value" screen by pressing "Input".

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.




m.

Press "Next" to set the compensation code to the ECM.

HINT:
·

If the setting process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure.

Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.




n.
A321643

To continue with compensation code registrations for other cylinders, press "Next". To finish the registration, press "Cancel".


o.

Turn the ignition switch off and then turn the tester off.


p.

Wait for at least 30 seconds.


q.

Turn the ignition switch to ON and then turn the tester on.


r.

Clear DTC P1601 stored in the ECM using the tester (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).


Hide 2.READ VIN

HINT:

Reading the VIN stored in the ECM is necessary when comparing to the VIN provided with the vehicle.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN.

NOTICE:

Do not start the engine.



e.

Select "VIN Read"


f.

Press "Next"


g.

Read the VIN.

HINT:

If the VIN code has not been registered or the ECM does not support the VIN read function, "Error VIN" will be displayed.



Hide 3.WRITE VIN

NOTICE:

The Vehicle Identification Number (VIN) must be input into the replacement ECM.


HINT:

The VIN is a 17-digit alphanumeric vehicle identification number. The intelligent tester is required to register the VIN.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN.

NOTICE:

Do not start the engine.



e.

Select "VIN Write"


f.

Press "Next"


g.

Press "Next" again.


h.

Press "Next" again to proceed.


i.

Press "Input".


j.

Manually input the VIN code using the keyboard on the tester screen. The code is a 17-digit, alphanumeric value imprinted.


k.

Press "OK".

HINT:

If "Error Inputting" appears after pressing "OK", reconfirm the VIN code for the vehicle and input the correct number again.



l.

Confirm that the correct VIN has been input, press "NEXT".

HINT:

If incorrect VIN has been input, press "Input" to return to the "Input VIN" screen and input the VIN again.



m.

Writing the VIN code.

NOTICE:

Do not press any buttons on the tester while the VIN is being written.



n.

To finish the registration, press "Exit".

HINT:

If "Error Writing" screen appears, check if the tester is connected properly. Perform the registration proceed again after turning the ignition switch off.



o.

Clear the DTC P0630 stored in the ECM on the tester.

i.

Turn the ignition switch off and then turn the tester off.


ii.

Wait for at least 30 seconds.


iii.

Turn the ignition switch to ON.


iv.

Turn the tester on.


v.

Clear the DTC.