Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P1238  Injector Malfunction  


DESCRIPTION

The ECM detects combustion deterioration for a specific cylinder.

HINT:
·

A cylinder which has an injection volume compensation value that varies from other cylinders may be malfunctioning.

·

If DTC P0093 (Fuel leaks in high-pressure area) is present simultaneously, a leak malfunction of the injector for the affected cylinder probably has occurred.

·

If DTC P0200 (Open or short in injector driver assembly or injector circuit) is present simultaneously, there probably is a fault in the circuit between the ECM and the injector. This fault may also be as a result of the injector driver assembly.

·

If only DTC P1238 (Injector malfunction) is present, the probable cause is an injector mechanical malfunction or insufficient compression (valve etc), not an open or short in the ECM, injector driver assembly and injector circuit.



DTC No. DTC Detection Condition Main Trouble Area Related Trouble Area
P1238 Engine speed fluctuation is large when idling
(2 trip detection logic)
·

Injector assembly

·

Injector driver assembly (P0200 is set simultaneously)

·

Open or short in engine wire harness (P0200 is set simultaneously)

·

Connector connection (P0200 is set simultaneously)

·

Compression pressure


·

Compression

·

Injector assembly



HINT:

After confirming DTC P1238, check the internal fuel pressure by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.

Reference:
Item Engine Speed Reference Value
Fuel Press Idling 25000 to 35000 kPa


MONITOR DESCRIPTION

P1238 (Injection malfunction, except open or short in injector circuit):

This DTC will be set if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor is also used to determine which cylinder has the problem. The fluctuation counter increments when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM sets this DTC.


CAUTION / NOTICE / HINT

NOTICE:

After replacing an injector, the ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


HINT:
·

After clearing the DTC, let the engine idle for 10 minutes after warm-up, and then confirm that P1238 is not present again.

·

If DTCs other than P1238 are present simultaneously, first perform troubleshooting for those DTCs.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P1238)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result:
Result Proceed to
P1238 A
P1238 and other DTCs B


HINT:

If codes other than P1238 are output, perform troubleshooting for those DTCs first.




A

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)

B

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)
HINT:

Check the wire harness and connector connections.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (COMPENSATION OF INJECTION VOLUME BETWEEN CYLINDERS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.READ VALUE USING INTELLIGENT TESTER (COMPENSATION OF INJECTION VOLUME BETWEEN CYLINDERS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.


e.

Read the value displayed on the tester.

Standard:

The compensatory injection volume (Injection Feedback Val #1 to #4) is from -9.9 to 9.9 mm3/st.


HINT:
·

If the injector is malfunctioning, the compensatory injection volume remains at -10.0 mm3/st or 10.0 mm3/st.

·

The compensatory injection volume is usually between -7.0 mm3/st and 7.0 mm3/st.




f.

Cylinders that have a compensation value which is more than the value specified above are considered to be faulty. Use the following steps to inspect and repair the cylinder.


Result:
Result Proceed to
Faulty cylinder is not identified A
Faulty cylinder is identified B



A

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

B

5.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

5.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
5.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
a.

Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-UH (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

6.CHECK IF DTC OUTPUT RECURS (DTC P1238)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

6.CHECK IF DTC OUTPUT RECURS (DTC P1238)
HINT:

After clearing the DTCs, let the engine idle for 10 minutes after warm-up, and then confirm that P1238 is not present again.


Result:
Proceed to
OK
NG



OK

NG

7.REPLACE INJECTOR ASSEMBLY
7.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly (Click here Engine / Hybrid System>N04C-UH (FUEL)>FUEL INJECTOR>REMOVAL).


Result:
Proceed to
NEXT



NEXT

8.CHECK IF DTC OUTPUT RECURS (DTC P1238)
8.CHECK IF DTC OUTPUT RECURS (DTC P1238)
HINT:

After clearing the DTCs, let the engine idle for 10 minutes after warm-up, and then confirm that P1238 is not present again.


Result:
Proceed to
NEXT



NEXT

END