Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM U

N04C-VQ ENGINE CONTROL  ECD SYSTEM  TERMINALS OF ECM  


E191646E25
0.573,0.656 1.083,0.896 0.51,0.24 1.583,0.656 2.094,0.896 0.51,0.24 3.135,0.656 3.646,0.896 0.51,0.24 4,0.656 4.5,0.896 0.5,0.24 4.865,0.656 5.375,0.896 0.51,0.24 6.031,0.656 6.542,0.896 0.51,0.24 0.708,0.688 1.021,0.875 0.313,0.188 10 false A57 1.74,0.688 2.198,0.885 0.458,0.198 10 false A56 3.219,0.688 3.677,0.885 0.458,0.198 10 false B105 6.135,0.688 6.594,0.885 0.458,0.198 10 false B102 4.969,0.688 5.427,0.885 0.458,0.198 10 false B103 4.115,0.688 4.573,0.885 0.458,0.198 10 false B104

HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Lock under "Terminal No. (Symbols)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A57-23 (BATT) - B102-1 (E1) GR - BR Battery (for measuring battery voltage and for ECM memory) Always 9 to 16 V
A56-24 (IGSW) - B102-1 (E1) B - BR Ignition switch Ignition switch ON 11 to 14 V
A57-24 (+B) - B102-1 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
A56-25 (MREL) - B102-1 (E1) W - BR EFI relay Ignition switch ON 11 to 14 V
5 seconds pass after ignition switch off 0 to 2 V
B104-13 (VC) - B104-14 (E2) L - R Power source of sensor (aspecific voltage) Ignition switch ON 4.5 to 5.5 V
A57-2 (VPA) - A56-5 (EPA) G - LG Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fullyreleased 0.6 to 1.0 V
Ignition switch ON, accelerator pedal fullydepressed 2.8 to 3.6 V
A57-1 (VPA2) - A56-3 (EPA2) GR - G Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fullyreleased 1.4 to 1.8 V
Ignition switch ON, accelerator pedal fullydepressed 3.6 to 4.4 V
A56-6 (VCPA) - A56-5 (EPA) L - LG Power source of accelerator pedal position sensor Ignition switch ON 4.5 to 5.5 V
B105-17 (VG) - B105-18 (EVG) G - L Mass air flow meter sub-assembly Idling with warm engine 1.5 to 1.9 V
B105-10 (THA) - B104-14 (E2) V - R Intake air temperature sensor (built into mass air flow meter sub-assembly) Idling with warm engine, IAT at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
B105-8 (THIA) - B104-14 (E2) Y - R Intake air temperature sensor (after turbocharged) Engine is warmed up: Idling, IAT at 0 to 80°C (32 to 176°F) 1.0 to 4.4 V
B105-9 (THW) - B104-14 (E2) G - R Engine coolant temperature sensor Idling, ECT at 80 to 120°C (176 to 248°F) 0.2 to 1.0 V
B105-21 (#1) - B102-1 (E1)
B105-22 (#2) - B102-1 (E1)
B105-23 (#3) - B102-1 (E1)
B105-24 (#4) - B102-1 (E1)
B - BR
W - BR
R - BR
G - BR
Injector assembly Idling with warm engine Pulse generation
(See waveform 1)
B103-13 (G+) - B103-14 (G-) R - G Camshaft position sensor Idling with warm engine Pulse generation
(See waveform 2)
B103-7 (NE+) - B103-8 (NE-) B - W Crankshaft position sensor Idling with warm engine Pulse generation
(See waveform 2)
A57-8 (STP) - B102-1 (E1) P - BR Stop light switch assembly Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 2 V
A57-9 (ST1-) - B102-1 (E1) V - BR Stop light switch assembly (opposite to STP) Ignition switch ON, brake pedal depressed 0 to 2 V
Ignition switch ON, brakepedal released 11 to 14 V
A56-23 (TC) - B102-1 (E1) P - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A57-6 (STA) - B102-1 (E1) B - BR Starter signal Cranking 6 V or higher
A57-18 (TAC) - B102-1 (E1) B - BR Engine speed Idling Pulse generation
(See waveform 3)
A57-19 (W) - B102-1 (E1) L - BR MIL MIL illuminated 0 to 2 V
MIL not illuminated 11 to 14 V
A57-7 (SPD) - B102-1 (E1) Y - BR Speed signal from combination meter Ignition switch ON, driving wheel slowly rotated Pulse generation
(See waveform 4)
B104-5 (PIM) - B104-14 (E2) P - R Manifold absolute pressure sensor Applied negative pressure of 93 kPa [abs] (697 mmHg,27.5 in.Hg) 0.25 to 0.4 V
Applied positive pressure of 150 kPa [abs] (1125 mmHg,44.3 in.Hg) 1.0 to 1.4 V
B104-20 (IREL) - B102-1 (E1) R - BR EDU relay Ignition switch ON or Idling 0 to 1.5 V
B105-16 (PCR1) - B104-14 (E2) L - R Fuel pressure main sensor (built into common rail assembly) Idling (Approximately 30 MPa (306 kgf/cm2, 4351 psi)) 1.7 to 2.2 V
B105-4 (THF) - B104-14 (E2) Y - R Fuel temperature sensor (built into injection or supply pump assembly) Ignition switch ON 1.2 to 1.6 V
B103-15 (VCG) - B103-14 (G-) L - G Power source of camshaft position sensor Ignition switch ON 4.5 to 5.5 V
B103-23 (PCV+) - B103-12 (PCV-) L - L Suction control valve (built into injection or supply pump assembly) Idling Pulse generation
(See waveform 5)
B105-20 (INJF) - B102-1 (E1) B - BR Injector driver assembly Idling with warm engine Pulse generation
(See waveform 6)
B104-3 (VLU) - B104-14 (E2) W - R Throttle position sensor (built into diesel throttle body assembly) Ignition switch ON, throttle valve fully closed 0.5 to 1.5 V
Ignition switch ON, throttle valve fully opened 3.2 to 4.2 V
B103-16 (LUSL) - B102-1 (E1) W - BR Throttle actuator (built into diesel throttle body assembly) duty signal Accelerator pedal released → Accelerator pedal depressed (when throttle motor is operating) Pulse generation
(See waveform 7)
B102-3 (EXB) - B102-1 (E1) GR - BR Exhaust brake Exhaust brake operating 11 to 14 V
B103-21 (NUSW) - B102-1 (E1) GR - BR Exhaust brake neutral switch assembly Ignition switch ON, shift position is neutral 11 to 14 V
Ignition switch ON, shift position is not neutral 0 to 2 V
A57-21 (CLSW) - B102-1 (E1) G - BR Exhaust brake clutch switch (exhaust retarder switch assembly) Clutch pedal depressed 0 to 2 V
Clutch pedal released 11 to 14 V
A57-20 (EXSW) - B102-1 (E1) P - BR Combination switch Exhaust brake switch on 11 to 14 V
Exhaust brake switch off 0 to 2 V
B103-26 (RSW) - B102-1 (E1) R - BR Back-up light switch Back-up light switch off 0 to 2 V
Back-up light switch on 11 to 14 V
A56-7 (CANH) - B102-1 (E1) B - BR CAN communication line Engine stop and Ignition switch ON Pulse generation
(See waveform 8)
A56-1 (CANL) - B102-1 (E1) W - BR CAN communication line Engine stop and Ignition switch ON Pulse generation
(See waveform 9)
B104-12 (CAN+) - B102-1 (E1) B - BR CAN Communication line Engine stop and ignition switch ON Pulse generation
(See waveform 8)
B104-6 (CAN-) - B102-1 (E1) W - BR CAN Communication line Engine stop and ignition switch ON Pulse generation
(See waveform 9)
B102-1 (E1) - Body ground BR - - Ground Always Below 1 Ω
B104-14 (E2) - Body ground R - - Ground Always Below 1 Ω
B102-11 (E01) - Body ground BR - - Ground Always Below 1 Ω
B102-12 (E02) - Body ground BR - - Ground Always Below 1 Ω
A57-11 (EC) - Body ground W-B - - Ground Always Below 1 Ω
B105-13 (VC2) - B105-14 (E21) R - R Power source of fuel pressure sensor for PCR2 (a specific voltage) Ignition switch ON 4.5 to 5.5 V
B105-14 (E21) - Body ground R - - Ground Always Below 1 Ω
B105-2 (PCR2) - B105-14 (E21) LG - R Fuel pressure sub sensor (built into common rail assembly) Idling (Approximately 30 MPa (306 kgf/cm2, 4351 psi)) 1.2 to 1.6 V

Waveform 1


A256727E01
0.24,0.538 0.651,0.722 0.411,0.184 10 (A) #1 0.24,0.899 0.651,1.083 0.411,0.184 10 (B) #3 0.24,1.271 0.651,1.455 0.411,0.184 10 (C) #4 0.24,1.62 0.651,1.804 0.411,0.184 10 (D) #2 2.929,0.551 3.268,0.701 0.34,0.15 10 GND 2.929,0.923 3.268,1.073 0.34,0.15 10 GND 2.929,1.289 3.268,1.439 0.34,0.15 10 GND 2.929,1.64 3.268,1.79 0.34,0.15 10 GND 2.696,0.056 3.238,0.208 0.542,0.152 10 5 V/DIV. 1.302,1.939 2.051,2.089 0.75,0.15 10 20 ms./DIV.

a.

Injector assembly No. 1 injection signal (A)


b.

Injector assembly No. 3 injection signal (B)


c.

Injector assembly No. 4 injection signal (C)


d.

Injector assembly No. 2 injection signal (D)

Item Content
Terminal No. (Symbols) (A) B105-21 (#1) - B102-1 (E1)
(B) B105-23 (#3) - B102-1 (E1)
(C) B105-24 (#4) - B102-1 (E1)
(D) B105-22 (#2) - B102-1 (E1)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.




Waveform 2


A256728E02
0.185,1.178 0.633,1.362 0.448,0.184 10 (A) NE 0.3,0.402 0.655,0.586 0.355,0.184 10 (B) G 2.934,0.61 3.274,0.76 0.34,0.15 10 GND 2.934,1.171 3.274,1.321 0.34,0.15 10 GND 2.571,0.052 3.131,0.204 0.559,0.152 10 5 V/DIV. 1.284,1.935 2.034,2.085 0.75,0.15 10 20 ms./DIV.

a.

Crankshaft position sensor signal (A)


b.

Camshaft position sensor signal (B)

Item Content
Terminal No. (Symbols) (A) B103-7 (NE+) - B103-8 (NE-)
(B) B103-13 (G+) - B103-14 (G-)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the engine speed.




Waveform 3


A256729E01
2.967,0.996 3.307,1.146 0.34,0.15 10 GND 2.712,0.096 3.251,0.248 0.539,0.152 10 5 V/DIV. 1.27,1.903 2.02,2.053 0.75,0.15 10 20 ms./DIV.

a.

Engine speed signal

Item Content
Terminal No. (Symbols) A57-18 (TAC) - B102-1 (E1)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.




Waveform 4


A256730E01
2.955,1.197 3.295,1.347 0.34,0.15 10 GND 2.708,0.11 3.249,0.261 0.542,0.152 10 2 V/DIV. 1.272,1.917 2.022,2.067 0.75,0.15 10 20 ms./DIV.

a.

Vehicle speed signal

Item Content
Terminal No. (Symbols) A57-7 (SPD) - B102-1 (E1)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, driving wheel slowly rotated

HINT:

The wavelength becomes shorter as the vehicle speed increases.




Waveform 5


A256731E01
2.872,1.128 3.212,1.278 0.34,0.15 10 GND 2.621,0.069 3.249,0.221 0.628,0.152 10 10 V/DIV. 1.199,1.892 1.874,2.042 0.675,0.15 10 5 ms./DIV.

a.

Suction control valve signal

Item Content
Terminal No. (Symbols) B103-23 (PCV+) - B103-12 (PCV-)
Tool Setting 10 V/DIV., 5 ms./DIV.
Condition Idling

HINT:

The waveform varies depending on the suction control valve operation.




Waveform 6


a.
A256732E01
2.912,0.937 3.252,1.087 0.34,0.15 10 GND 2.72,0.07 3.263,0.222 0.543,0.152 10 2 V/DIV. 1.238,1.863 1.988,2.013 0.75,0.15 10 20 ms./DIV.

Injector injection confirmation signal

Item Content
Terminal No. (Symbols) B105-20 (INJF) - B102-1 (E1)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.




Waveform 7


a.
A256733E01
2.961,1.38 3.301,1.53 0.34,0.15 10 GND 2.718,0.072 3.254,0.224 0.536,0.152 10 1 V/DIV. 1.328,1.897 2.004,2.047 0.675,0.15 10 2 ms./DIV.

Throttle actuator signal

Item Content
Terminal No. (Symbols) B103-16 (LUSL) - B102-1 (E1)
Tool Setting 1 V/DIV., 2 ms./DIV.
Condition Accelerator pedal released → Accelerator pedal depressed (when throttle motor is operating)

HINT:

The waveform varies depending on the throttle valve operation.




Waveform 8 (Reference)


A303295E05
2.771,0.167 3.385,0.375 0.615,0.208 10 false 1 V/DIV. 2.958,1.25 3.344,1.5 0.385,0.25 10 false GND 1.573,1.781 2.344,1.99 0.771,0.208 10 false 10 μs./DIV.

a.

CAN communication signal

Item Content
Terminal No. (Symbols) A56-7 (CANH) - B102-1 (E1)
B104-12 (CAN+) - B102-1 (E1)
Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Engine stop and Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




Waveform 9 (Reference)


A303296E06
2.802,0.156 3.396,0.385 0.594,0.229 10 false 1 V/DIV. 2.99,1.229 3.333,1.469 0.344,0.24 10 false GND 1.615,1.76 2.417,1.958 0.802,0.198 10 false 10 μs./DIV.

a.

CAN communication signal

Item Content
Terminal No. (Symbols) A56-1 (CANL) - B102-1 (E1)
B104-6 (CAN-) - B102-1 (E1)
Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Engine stop and Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.