Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM D

N04C-VQ ENGINE CONTROL  ECD SYSTEM  FREEZE FRAME DATA  


DESCRIPTION



The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.


A301856E26
2.24,0.938 3.083,1.167 0.844,0.229 10 false 0.5 seconds 0.344,0.938 1.188,1.167 0.844,0.229 10 false 0.5 seconds 1.323,0.927 2.167,1.156 0.844,0.229 10 false 0.5 seconds 0.406,2.813 2.844,3.031 2.438,0.219 10 false Freeze frame data which can be read 2.427,0.302 3.229,0.563 0.802,0.26 10 false DTC stored

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data can be checked.

·

3 data sets before the DTC was stored.

·

1 data set when the DTC was stored.

·

1 data set after the DTC was stored.

These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.


LIST OF FREEZE FRAME DATA


GTS Display Measurement Item Diagnostic Note
Vehicle Speed Vehicle speed Speed indicated on speedometer
Target Idle Engine Speed Target idling speed -
Engine Speed Engine speed -
Calculate Load Calculated load Calculated load by ECM
MAF Mass air flow volume If approximately 0.0 gm/s:
·

Mass air flow meter sub-assembly power source circuit is open or shorted

·

VG circuit is open or shorted

·

EVG circuit is open


Atmosphere Pressure Atmosphere pressure -
MAP Absolute pressure inside intake manifold -
Coolant Temp Engine coolant temperature If -40°C (-40°F), sensor circuit is open
If 140°C (284°F), sensor circuit is shorted
Intake Air Intake air temperature If -40°C (-40°F), sensor circuit is open
If 140°C (284°F), sensor circuit is shorted
Intake Air Temp (Turbo) Intake air temperature after intercooler If -40°C (-40°F), sensor circuit is open
If 190°C (374°F) or more, sensor circuit is shorted
Engine Run Time Accumulated engine running time -
Initial Engine Coolant Temp Engine coolant temperature at engine start -
Initial Intake Air Temp Intake air temperature at engine start -
Battery Voltage Battery voltage -
Pre Glow Pre glow operation -
After Glow After glow operation -
Accel Position Accelerator pedal position sensor -
Accel Sens. No.1 Volt % Accelerator pedal position No. 1 output voltage -
Accel Sens. No.2 Volt % Accelerator pedal position No. 2 output voltage -
Target Throttle Position Target throttle position -
Actual Throttle Position Actual throttle position -
Diesel Throttle Learn Status Diesel throttle learning status -
Throttle Sensor Volt % Throttle position sensor output voltage -
Throttle Motor DUTY Throttle actuator -
Injection Volume Injection volume -
Inj. FB Vol. for Idle Injection volume feedback value for idle speed control -
Inj Vol Feedback Learning Injection volume feedback learning value -
Injection Feedback Val #1 Injection volume correction for cylinder 1 -
Injection Feedback Val #2 Injection volume correction for cylinder 2 -
Injection Feedback Val #3 Injection volume correction for cylinder 3 -
Injection Feedback Val #4 Injection volume correction for cylinder 4 -
Pilot 1 Injection Period Pilot 1 injection period -
Pilot 2 Injection Period Pilot 2 injection period -
Main Injection Period Main injection period -
After Injection Period Post injection period -
Pilot 1 Injection Timing Pilot 1 injection timing -
Pilot 2 Injection Timing Pilot 2 injection timing -
Main Injection Timing Main injection timing -
After Injection Timing Post injection timing -
Injector Memory Error EEPROM malfunction for injector assembly -
Target Common Rail Pressure Target common rail pressure -
Fuel Press Fuel pressure -
Fuel Temperature Fuel temperature -
Fuel Return Temp Fuel return temperature -
Target Pump SCV Current Pump current target final value -
Pump SCV Learning Value Pump current learning value -
Target EGR Position Target EGR valve position -
EGR Initial Step Position EGR initial step position -
Actual EGR Valve Pos. Actual EGR valve position -
EGR Close Lrn. Status EGR valve fully closed position learning status -
EGR Operation Prohibit EGR operation prohibit -
Target Booster Pressure Target booster pressure -
VN Turbo Command VN turbo command -
Actual VN Position Actual VN turbo position -
Exhaust Brake Switch Exhaust brake switch -
Starter Signal Starter signal -
IG SW Ignition switch status -
Clutch Switch Exhaust retarder switch status -
Reverse Switch Reverse switch -
Stop Light Switch Stop light switch -
A/C Signal Air conditioning signal -
Engine Stop SW Engine stop switch -
Time after DTC Cleared Cumulative time after DTC cleared -
Distance from DTC Cleared Accumulated distance after DTC cleared -
Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared -
TC and TE1 TC and TE1 terminals of DLC3 -
Engine Start Time - -
Engine Speed (Starter Off) - -
Starter Count - -
Run Dist of Previous Trip - -
Glow Request Lighting Time Glow request lighting time -
IG-ON Time Ignition switch ON time before engine start -
MAF Low Mass air flow low -
Boost Pressure Low Boost pressure low -
Common Rail Pressure Low Common rail pressure low -
Engine Coolant Temp High Engine coolant temperature high -
MAF/Estimate MAF Ratio Indicates the ration of estimated intake air volume and actual intake -
Engine Warm Up Switch Warm up switch -
ACT VSV Air conditioning cut operation -