Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM U

N04C-VQ ENGINE CONTROL  ECD SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:
·

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

Normal Condition: If no idling conditions are specified, the shift lever is in neutral, and the A/C switch and all accessory switches are off.



NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the "Data List".

Tester Display Measurement Item/Range Normal Condition Diagnostic Notes
Vehicle Speed Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on speedometer
Target Idle Engine Speed Target idling engine speed:
Min.: 0 rpm, Max.: 51199 rpm
Idling: 600 to 700 rpm After warming-up engine
Engine Speed Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
Idling: 600 to 700 rpm After warming-up engine
Calculate Load Calculated load by ECM:
Min.: 0%, Max.: 100%
Idling: 10 to 25%
Running without load (2500 rpm): 7.5 to 14.5%
-
MAF Air flow rate from mass air flow meter sub-assembly:
Min.: 0 gm/s, Max.: 655.35 gm/s
Idling: 5.0 to 20.0 gm/s
Running without load (3600 rpm): 125 to 165gm/s
If approximately 0 gm/s:
·

Mass air flow meter sub-assembly power source circuit is open or shorted

·

VG circuit is open or shorted

·

EVG circuit is open


Atmosphere Pressure Atmospheric pressure value:
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912 mmHg)
Actual atmospheric pressure -
MAP Absolute pressure inside intake manifold:
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912 mmHg)
·

Idling: 90 to 100 kPa or less

·

Engine running at 3600 rpm: 128 to 165 kPa or more


-
Coolant Temp Engine coolant temperature:
Min.: -40°C, Max.: 140°C
After warming up engine: 80 to 100°C (176 to 212°F) If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Intake air temperature:
Min.: -40°C, Max.: 140°C
Equivalent to temperature at location of mass air flow meter sub-assembly If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Temp (Turbo) Intake air temperature (Turbo):
Min.: -40°C, Max.: 190°C
65°C (149°F) or less -
Engine Run Time Engine run time:
Min.: 0 s, Max.: 65535 s
Time after engine started Service data
Initial Engine Coolant Temp Initial engine coolant temperature:
Min.: -40°C, Max.: 120°C
Engine coolant temperature when engine starts -
Initial Intake Air Temp Initial intake air temperature:
Min.: -40°C, Max.: 120°C
Intake air temperature when engine starts -
Battery Voltage Battery voltage:
Min.: 0 V, Max.: 65.5 V
Idling: 11 to 14 V -
Pre Glow Pre glow operation:
ON or OFF
- -
After Glow After glow operation:
ON or OFF
- -
Accel Position Accelerator position status:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 0%

·

Accelerator pedal depressed: 68 to 99.6%


-
Accel Sens. No.1 Volt % Accelerator position No. 1:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 12 to 20%

·

Accelerator pedal depressed: 56 to 72%


-
Accel Sens. No.2 Volt % Accelerator position No. 2:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 28 to 36%

·

Accelerator pedal depressed: 72 to 88%


-
Accel Sensor Out No.1 Accelerator position No. 1 voltage:
Min.: 0 V, Max.: 5 V
Accelerator pedal released: 0.6 to 1.0 V
Accelerator pedal fully depressed: 2.8 to 3.6 V
Read value with ignition switch to ON (Do not start engine)
Accel Sensor Out No.2 Accelerator position No. 2 voltage:
Min.: 0 V, Max.: 5 V
Accelerator pedal released: 1.4 to 1.8 V
Accelerator pedal fully depressed: 3.6 to 4.4 V
Read value with ignition switch to ON (Do not start engine)
Target Throttle Position Target throttle position:
Min.: -128%, Max.: 127%
·

Throttle valve fully opened: 0%

·

Throttle valve fully closed: 100%


-
Actual Throttle position Actual diesel throttle position:
Min.: -128%, Max.: 127%
Idling after warmed-up engine: 81 to 95% -
Throttle Close Learning Val. Throttle valve fully closed:
Min.: 0 deg, Max.: 84 deg
- -
Diesel Throttle Learn Status Diesel throttle learning status:
OK or NG
OK -
Throttle Sensor Volt % Throttle position sensor output voltage:
Min.: 0%, Max.: 100%
- -
Throttle Motor DUTY Throttle actuator duty:
Min.: 0%, Max.: 100%
Idling after warming up engine: 30 to 100% -
Injection Volume Injection volume:
Min.: 0 mm3/st, Max.: 1279.98 mm3/st
Idling: 5.0 to 15.0 mm3/st -
Inj. FB Vol. for Idle Idle stable control:
Min.: -80 mm3/st, Max.: 79.99 mm3/st
-10 to 10 mm3/st -
Inj Vol Feedback Learning Injection volume feedback learning value:
Min.: -10 mm3/st, Max.: 9.9 mm3/st
Idling: -0.4 to 1.0 mm3/st -
Injection Feedback Val #1 Injection volume correction for cylinder 1:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -2.0 to 2.0 mm3/st -
Injection Feedback Val #2 Injection volume correction for cylinder 2:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -2.0 to 2.0 mm3/st -
Injection Feedback Val #3 Injection volume correction for cylinder 3:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -2.0 to 2.0 mm3/st -
Injection Feedback Val #4 Injection volume correction for cylinder 4:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -2.0 to 2.0 mm3/st -
Pilot 1 Injection Period Pilot 1 Injection period:
Min.: 0 μs, Max.: 65535 μs
Idling after warming up engine: 0 μs -
Pilot 2 Injection Period Pilot 2 Injection period:
Min.: 0 μs, Max.: 65535 μs
Idling: 500 to 600 μs -
Main Injection Period Pilot 1 Injection period:
Min.: 0 μs, Max.: 65535 μs
Idling: 450 to 800μs -
After Injection Period After Injection period:
Min.: 0 μs, Max.: 65535 μs
- -
Pilot 1 Injection Timing Pilot 1 Injection timing:
Min.: -70°CA, Max.: 20°CA
- -
Pilot 2 Injection Timing Pilot 2 Injection timing:
Min.: -50°CA, Max.: 20°CA
Idling: -11 to -9°CA -
Main Injection Timing Main Injection timing:
Min.: -90°CA, Max.: 90°CA
Idling: -1 to 1°CA -
After Injection Timing After Injection timing:
Min.: -10°CA, Max.: 50°CA
- -
Injector Memory Error Injector Memory Error:
No Error or Error
No Error If the injector compensation codes are not input into the new ECM, or if a injector compensation code of a different injector model or a compensation code representing a value which exceeds the compensation setting range is input into the new ECM, DTC P062F is stored and "Injector Memory Error" displays "Error".
Injection Pressure Correction Injection pressure correction:
Min.: -500 mm3/st, Max.: 780 mm3/st
-400 to 400 mm3/st -
Target Common Rail Pressure Target common rail pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 20000 to 30000 kPa -
Fuel Press Fuel pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 20000 to 30000 kPa -
Common Rail Pres Sens 2 Fuel pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 20000 to 30000 kPa This is a backup output value from the fuel pressure sensor.
Fuel Temperature Fuel temperature:
Min.: -40°C, Max.: 215°C
Actual fuel temperature -
Fuel Return Temp Fuel return temperature:
Min.: -40°C, Max.: 215°C
- -
Target Pump SCV Current Pump open current value:
Min.: 0 mA, Max.: 8191.8 mA
Idling: 1350 to 2200 mA -
Pump SCV Learning Value Pump current learning value:
Min.: -4096 mA, Max.: 4095.8 mA
- -
Target EGR Position Target EGR position:
Min.: 0%, Max.: 100%
Idling: 15 to 30% -
EGR Initial Step Position EGR initial step position
Min.: 0 step, Max.: 255 step
- -
Actual EGR Valve Pos. Actual EGR valve position:
Min.: 0%, Max.: 100%
Idling: 15 to 30 % -
EGR Close Lrn. Status EGR learning status:
OK or NG
OK -
EGR Operation Prohibit EGR operation prohibit:
OK or NG
OK -
Target Booster Pressure Target booster pressure:
Min.: -640 kPa, Max.: 639.98 kPa
Idling after warning up engine and vehicle is under normal atmospheric pressure: 90 to 110 kPa -
Boost Pressure Deviation Boost pressure deviation:
Min.: -320 kPa, Max.: 320 kPa
- -
VN Turbo Command VN turbo command:
Min.: -128%, Max.: 127%
- -
Actual VN Position Actual VN turbo position:
Min.: 0%, Max.: 127.5%
- -
VN Turbo Type VN turbo type:
Not Avl, Common, Vacuum, CAN Com or DC
CAN Com -
VN Turbo Max Angle VN turbo maximum angle :
Min.: 0%, Max.: 100%
100% -
VN Turbo Min Angle VN turbo minimum angle :
Min.: 0%, Max.: 100%
7.5% -
VN Turbo Operation Prohibit VN turbocharger operation prohibition:
ON or NG
- -
Exhaust Brake Switch Exhaust brake switch status:
ON or OFF
Exhaust brake operated: ON -
Starter Signal Starter signal:
ON or OFF
Cranking: ON -
IG SW Ignition switch status:
ON or OFF
·

Ignition switch ON: ON

·

Ignition switch off: OFF


-
Clutch Switch Exhaust retarder switch status:
ON or OFF
Exhaust retarder switch on: ON -
Reverse Switch Reverse switch:
ON or OFF
·

Shift lever in reverse: ON

·

Shift lever not in reverse: OFF


-
Stop Light Switch Stop light switch status:
ON or OFF
·

Brake pedal depressed: ON

·

Brake pedal released: OFF


-
A/C Signal Air conditioning signal:
ON or OFF
Air conditioning operate: ON -
Engine Stop SW Engine stop switch:
ON or OFF
- -
Check Mode Check mode:
ON or OFF
Check mode on: ON Click here(Click here)
SPD Test Result Check mode result for vehicle speed sensor:
COMPL or INCMPL
COMPL -
Complete Parts Monitor Comprehensive component monitor/
Not Avl or Avail
- *
Fuel System Monitor Fuel system monitor/
Not Avl or Avail
- *
Misfire Monitor Misfire monitor/
Not Avl or Avail
- *
EGR/VVT Monitor EGR/VVT monitor
Not Avl or Avail/
- *
EGR/VVT Monitor EGR/VVT monitor
Compl or Incmpl
- *
O2S(A/FS) Heater Monitor O2S(A/FS) heater monitor/
Not Avl or Avail
- *
O2S(A/FS) Heater Monitor O2S(A/FS) heater monitor/
Compl or Incmpl
- *
O2S(A/FS) Monitor O2S(A/FS) monitor/
Not Avl or Avail
- *
O2S(A/FS) Monitor O2S(A/FS) monitor/
Compl or Incmpl
- *
A/C Monitor A/C monitor/
Not Avl or Avail
- *
A/C Monitor A/C monitor/
Compl or Incmpl
- *
2nd Air Monitor 2nd air monitor/
Not Avl or Avail
- *
2nd Air Monitor 2nd air monitor/
Compl or Incmpl
- *
EVAP Monitor EVAP monitor/
Not Avl or Avail
- *
EVAP Monitor EVAP monitor/
Compl or Incmpl
- *
Heated Catalyst Monitor Heated catalyst monitor/
Not Avl or Avail
- *
Heated Catalyst Monitor Heated catalyst monitor/
Compl or Incmpl
- *
Catalyst Monitor Catalyst monitor/
Not Avl or Avail
- *
Catalyst Monitor Catalyst monitor/
Compl or Incmpl
- *
# Codes (Include History) Number of codes:
Min.: 0, Max.: 255
- Number of detected DTCs
MIL MIL status:
ON or OFF
MIL ON: ON -
MIL ON Run Distance MIL ON run distance:
Min.: 0 km, Max.: 65535 km
Distance after DTC detected -
Running Time from MIL ON Running time from MIL on:
Min.: 0 min, Max.: 65535 min
Equivalent to running time after MIL turns on -
Time after DTC Cleared Time after DTC cleared:
Min.: 0 min, Max.: 65535 min
Equivalent to time after DTCs cleared -
Distance from DTC Cleared Distance after DTC cleared:
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs cleared -
Warmup Cycle Cleared DTC Warm up cycle after DTC cleared:
Min.: 0, Max.: 255
- Number of warm up cycles after DTC cleared
OBD Requirements Identifying OBD requirement Heavy Duty Euro OBD Stage I with NOx control -
Number of Emission DTC (Number of emission DTC) - -
TC and TE1 TC and TE1 terminal of DLC3:
ON or OFF
- -
Engine Start Time Engine start time:
Min.: 0 ms. Max.: 267386 ms.
- -
Engine Speed (Starter Off) Engine speed when starter off:
Min.: 0 rpm, Max.: 1593 rpm
- -
Starter Count Starter on count:
Min.: 0, Max.: 255
- -
Run Dist of Previous Trip Distance driven during previous trip:
Min.: 0 km, Max.: 326 km
- -
Glow Request Lighting Time Glow request lighting time:
Min.: 0 ms. Max.: 33423 ms.
- -
IG-ON Time Ignition switch ON time before engine start:
Min.: 0 ms. Max.: 33423 ms.
- -
MAF Low Mass air flow low:
ON or OFF
OFF -
Boost Pressure Low Boost pressure low:
ON or OFF
OFF -
Common Rail Pressure Low Common rail pressure low:
ON or OFF
OFF -
Engine Coolant Temp High Engine coolant temperature high:
ON or OFF
OFF -
MAF/Estimate MAF Ratio Indicates the ratio of estimated intake air volume and actual intake air volume:
Min.: 0, Max.: 2.55
- -
Engine Warm Up Switch Warm up switch status:
ON or OFF
Warm up switch on: ON -
ACT VSV Air conditioning cut signal:
ON or OFF
- -
Model Code Model code - Identifying model code: XZB53
Engine Type Engine type - Identifying engine type: N04CVQ
Cylinder Number Identifying cylinder number:
Min.: 0, Max.: 255
- Identifying cylinder number: 4
Destination Destination - Identifying destination: C
Model Year Identifying model year:
Min.: 1900, Max.: 2155
- Identifying model year: 20##
Engine Speed of Cyl #1 Engine Speed for cylinder No. 1:
Min.: 0 rpm, Max.: 51199 rpm
Engine speeds of all cylinders almost same Output only when Check the Cylinder Compression performed using active test.
51199 rpm: Not performed using active test.
Engine Speed of Cyl #2 Engine Speed for cylinder No. 2:
Min.: 0 rpm, Max.: 51199 rpm
Engine speeds of all cylinders almost same Output only when Check the Cylinder Compression performed using active test.
51199 rpm: Not performed using active test.
Engine Speed of Cyl #3 Engine Speed for cylinder No. 3:
Min.: 0 rpm, Max.: 51199 rpm
Engine speeds of all cylinders almost same Output only when Check the Cylinder Compression performed using active test.
51199 rpm: Not performed using active test.
Engine Speed of Cyl #4 Engine Speed for cylinder No. 4:
Min.: 0 rpm, Max.: 51199 rpm
Engine speeds of all cylinders almost same Output only when Check the Cylinder Compression performed using active test.
51199 rpm: Not performed using active test.
Av Engine Speed of All Cyl Average engine Speed for all cylinders:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using active test.
51199 rpm: Not performed using active test.
Target Engine Speed Target engine speed:
Min.: 0 rpm, Max.: 5000 rpm
Idling: 600 to 700 rpm -
Target Common Rail Press Target common rail pressure:
Min.: 0 MPa, Max.: 256 MPa
Idling: 24 to 26MPa -
Pump Mode Injection or supply pump assembly control mode:
PCV, DUTY, Normal, STOP or IG OFF
- -
Injection Pump Learning Status Injection or supply pump assembly learning status:
Compl or Incmpl
Compl -
VN Turbo Valve Position Turbocharger opening value:
Min.: 0% Max.: 100%
- -
PCV Open Duty Suction control valve open duty:
Min.: 0% Max.: 100%
45 to 55% -
PCV Open Current FB Val Suction control valve open current feedback volume:
Min.: -6000 mA, Max.: 6000 mA
-400 to 400 mA -
Engine Overspeed History Engine overspeed history:
ON or OFF
OFF -

*:

Avail: The monitor is available on the vehicle.

Not Avl: The monitor is not available on the vehicle.

Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.



PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the "Active Test".

Tester Display Test Part Control Range Diagnostic Notes
Control the A/C Cut Signal Control the air conditioning cut signal OFF / ON Test possible when following conditions met:
·

Ignition switch ON

·

Engine stopped


Connect the TC and TE1 Turn on TC and TE1 connection OFF / ON Test possible when following conditions met:
·

Ignition switch ON

·

Engine stopped


Control the EGR Step Position Control the EGR valve step position 1 to 100% Test possible when following conditions met:
·

Ignition switch ON

·

Engine stopped

·

Vehicle stopped


Diesel Throttle Target Angle Control the diesel throttle valve 0 to 90% Test possible when following conditions met:
·

Engine idling

·

Vehicle stopped


Test the Turbo Charger Step Motor Control the turbocharger actuator 40 to 100% Test possible when following conditions met:
·

Engine idling

·

Vehicle stopped

·

Accelerator pedal fully released


Test the Fuel Leak Pressurizes common rail internal fuel pressure, and checks for fuel leaks Stop / Start
·

Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when Start is selected

·

Above conditions preserved while test is Start


Test possible when following conditions met:
·

Engine idling

·

Vehicle stopped


HINT:

If this Active Test is performed when the engine is cold, combustion may become unstable. However, this is not a malfunction. It is only necessary to confirm that the pressure rises to the target pressure and that there are no fuel leaks.


Active the VN Turbo Open Active the turbocharger Open / OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine running


Active the EGR Valve Close Active the EGR Valve Close / OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling

·

Shift lever in neutral


Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #4) injector assembly fuel cut #1/#2/#3/#4 ON/OFF Fuel injection is stopped while the test is ON.
·

Confirm that the vehicle is stopped and the engine is idling.

·

If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning.


Check the Cylinder Compression* Check the cylinder compression pressure OFF / ON Fuel injection stops in all cylinders
Activate the VSV for Exhaust Brake Activate the solenoid valve for exhaust brake OFF / ON Test possible when following conditions met:
·

Engine idling

·

Vehicle stopped



HINT:

*: When cranking the engine, the Active Test measures the speed of each cylinder. In this Active Test, the fuel of all cylinders is cut when the engine is cranked for approximately 10 seconds.


At this time, the speed of each cylinder is measured. If the speed of one cylinder is higher than the other cylinders, the compression pressure of that cylinder is determined to be lower than the other cylinders.

1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON and turn the GTS on.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / All Data / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4 and Av Engine Speed of All Cyl.

6.

Push the snapshot button to turn the snapshot function on.

HINT:

Using the snapshot function, data can be recorded during the Active Test.


7.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, the Active Test Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and the engine speed measurement enters standby mode.


8.

Crank the engine for about 10 seconds.

9.

Monitor the engine speed (Engine Speed of Cyl #1 to #4, Av Engine Speed of All Cyl) displayed on the GTS.

HINT:

After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.


NOTICE:
·

Do not crank the engine continuously for 20 seconds or more.

·

If Check the Cylinder Compression needs to be performed after it is turned ON and performed once, press Exit to return to the Active Test menu screen. Then perform Check the Cylinder Compression again.

·

Use a fully-charged battery.



10.

Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

NOTICE:

If the Active Test is changed to OFF while the engine is being cranked, the engine will start.


11.

Push the snapshot button to turn the snapshot function off.

12.

Select the recorded data and display the data as a graph.

13.

Check the change in engine speed values.