Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM J

N04C-VQ ENGINE CONTROL  ECD SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition switch to the starter relay and also flows to terminal STA of the ECM (STA signal).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.INSPECT ST RELAY

B

6.READ VALUE USING GTS (STARTER SIGNAL)
2.INSPECT ST RELAY
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM - ST RELAY)

NG

REPLACE ST RELAY

3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM - ST RELAY)
a.

Remove the starter relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the ignition switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J63-9 (ST2) - A57-6 (STA) Always Below 1 Ω
1 (ST relay holder) - A57-6 (STA) Always Below 1 Ω
J63-9 (ST2) or A57-6 (STA) - Body ground Always 10 kΩ or higher
1 (ST relay holder) or A57-6 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM - STARTER RELAY)

4.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (Click hereEngine / Hybrid System>N04C-VQ (STARTING)>IGNITION SWITCH>INSPECTION).


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY - STARTER ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Disconnect the starter assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (ST relay holder) - Battery positive (+) terminal Always Below 1 Ω
3 (ST relay holder) - B99-1 (ST) Always Below 1 Ω
5 (ST relay holder) or Battery positive (+) terminal - Body ground Always 10 kΩ or higher
3 (ST relay holder) or B99-1 (ST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER RELAY ASSEMBLY - STARTER ASSEMBLY)

6.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the valve displayed on the GTS when the ignition switch is turned to ON and START position.


OK:
Ignition Switch Condition Starter Signal
ON OFF
START ON


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
a.

Remove the starter relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the ignition switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
J63-9 (ST2) - A57-6 (STA) Always Below 1 Ω
J63-9 (ST2) or A57-6 (STA) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)