Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › VALVE BODY ASSEMBLY › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355868 VALVE BODY ASSEMBLY A

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35893 1.INSTALL CENTER SUPPORT APPLY GASKET

a.
Q002827

Coat 4 new center support apply gaskets with ATF and install it to the transmission case.


Hide 35410 2.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C102116E02
1.656,0.781 1.208,0.135 false 1.948,0.729 2.354,0.104 false 0.354,0.031 1.375,0.427 1.021,0.396 10 false Manual valve 2.396,0.021 3.198,1.01 0.802,0.99 10 true Manual valve Lever

Align the transmission valve body with the manual valve lever.


b.

Align of the manual valve with the transmission case.


c.
C174131E03
0.229,0.49 0.427,0.719 0.198,0.229 10 true A 0.229,0.875 0.427,1.104 0.198,0.229 10 true B 0.219,1.302 0.417,1.531 0.198,0.229 10 true C 0.208,1.708 0.406,1.938 0.198,0.229 10 true C 1.188,0.073 1.406,0.25 0.219,0.177 10 true D 1.042,0.688 1.229,0.885 0.188,0.198 10 true C 1.042,1.073 1.229,1.271 0.188,0.198 10 true E 1.083,1.531 1.271,1.729 0.188,0.198 10 true C 1.042,1.781 1.229,1.979 0.188,0.198 10 true F 1.604,1.333 1.792,1.531 0.188,0.198 10 true E 1.625,1.948 1.813,2.146 0.188,0.198 10 true G 1.969,1.885 2.167,2.115 0.198,0.229 10 true C 1.979,1.354 2.167,1.552 0.188,0.198 10 true H 2.344,0.104 2.563,0.302 0.219,0.198 10 true F 2.323,0.656 2.51,0.854 0.188,0.198 10 true B 2.781,0.375 2.979,0.604 0.198,0.229 10 true C 2.76,0.573 2.948,0.76 0.188,0.188 10 true I 2.771,0.75 3.01,0.927 0.24,0.177 10 true I 2.75,1.042 2.938,1.208 0.188,0.167 10 true C 2.771,1.229 2.958,1.417 0.188,0.188 10 true I 2.76,1.552 2.948,1.74 0.188,0.188 10 true J

Install the 21bolts.

Torque:

10 N*m (102 kgf*cm, 7 ft.*lbf)


NOTICE:

Tighten the bolts equally in several steps.


HINT:

Bolt length


Bolt Length
A 41 mm (1.6142 in.)
B 32 mm (1.2598 in.)
C 32 mm (1.2598 in.)
D 45 mm (1.7717 in)
E 52 mm (2.0472 in.)
F 28 mm (1.1024 in.)
G 37.5 mm (1.4764 in.)
H 57 mm (2.2441 in.)
I 22 mm (0.8661 in)
J 22 mm (0.8661 in)


Hide 82125J 3.CONNECT TRANSMISSION WIRE

a.
C174130E02
3.229,0.844 3.385,1.083 0.156,0.24 10 false A 3.229,0.552 3.427,0.802 0.198,0.25 10 false A 3.24,1.125 3.385,1.354 0.146,0.229 10 false A 3.24,1.406 3.427,1.698 0.188,0.292 10 false A 1.083,2.354 1.281,2.552 0.198,0.198 10 false A 2.438,3.031 2.771,3.292 0.333,0.26 10 false B

Connect the 5 connectors to the solenoid valves.(A)


b.

Connect the ATF temperature sensor's clamp.(B)


Hide 35261A 4.INSTALL THROTTLE PRESSURE ACCUMULATOR CYLINDER

a.
C174129

Coat a new center support apply gasket with ATF and install it to the throttle pressure accumulator cylinder.


b.

Install the throttle pressure accumulator cylinder and clamp with the 3 bolts.

Torque:

5.5 N*m (56 kgf*cm, 49 in.*lbf)



Hide 35330 5.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C174128

Install a new gasket on the valve body oil strainer assembly.


b.

Install the valve body oil strainer assembly with the 4 bolts.

Torque:

10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 35106 6.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.

Remove any packing material.


b.
C103317E02
1.115,0.656 0.76,1.021 0.76,1.021 1.115,1.385 false 2.042,0.656 2.635,1.01 2.635,1.01 2.042,1.385 false 2.677,0.927 3.385,1.365 0.708,0.438 10 true Magnets 0.073,0.927 0.729,1.365 0.656,0.438 10 true Magnets

Clean the 4 transmission oil cleaner magnets and install them to the automatic transmission oil pan sub-assembly.

HINT:

Install the magnets as shown in the illustration.



c.
C102375

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Standard seal diameter:

2 to 3 mm (0.079 to 0.118 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes after applying seal packing.

·

Do not add ATF for at least 2 hours after the installation.




d.
C102111

Install the automatic transmission oil pan sub-assembly with the 20 bolts.

Torque:

7 N*m (71 kgf*cm, 5 in.*lbf)


NOTICE:

Tighten the bolts equally in several steps.



Hide 35013 7.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

3.9 N*m (40 kgf*cm, 35 in.*lbf)


Hide 11.INSPECT FOR OIL LEAK