Home › Drivetrain › CLUTCH › CLUTCH UNIT (for M551)
RM2850E _52 Drivetrain _073140 CLUTCH _0355891 CLUTCH UNIT(for M551) A

CLUTCH  CLUTCH UNIT(for M551)  INSTALLATION  


PROCEDURE

Hide 33311W 1.INSTALL INPUT SHAFT BEARING

a.
C091689

Using SST and hammer, install a new input shaft bearing.SST

SST
09304-12012  

HINT:

After installing the input shaft bearing to the hub, make sure that it rotates smoothly.



b.

Install the 2 bolts.

Torque:

190 N*m (1937 kgf*cm, 140 ft.*lbf)



Hide 33311W 2.INSPECT INPUT SHAFT BEARING

a.
Q002481

Turn the bearing by hand while applying force in the rotation direction.

If the bearing is stuck or difficult to turn, replace the input shaft bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 31250 3.INSTALL CLUTCH DISC ASSEMBLY

a.
C142544

Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

SST
09301-00110  

NOTICE:

Insert the clutch disc assembly in the correct orientation.



Hide 31210 4.INSTALL CLUTCH COVER ASSEMBLY

C103830N02
0.74,0.333 1.26,0.333 true 0.417,0.656 0.938,0.656 true 0.406,1.521 0.927,1.521 true 0.729,1.844 1.25,1.844 true 2.177,0.323 2.698,0.323 true 2.5,0.656 3.021,0.656 true 2.479,1.521 3,1.521 true 2.177,1.833 2.698,1.833 true 0.271,0.573 0.427,0.771 0.156,0.198 10 false 7 0.594,0.25 0.75,0.448 0.156,0.198 10 false 4 0.25,1.438 0.406,1.635 0.156,0.198 10 false 2 0.573,1.771 0.729,1.969 0.156,0.198 10 false 8 2.74,0.24 2.896,0.438 0.156,0.198 10 false 9 3.052,0.563 3.375,0.792 0.323,0.229 10 false 1, 5 3.042,1.438 3.198,1.635 0.156,0.198 10 false 6 2.74,1.74 2.896,1.938 0.156,0.198 10 false 3

a.

Align the matchmarks on the clutch cover assembly and flywheel sub-assembly.


b.

Following the procedures shown in the illustration, tighten the 8 bolts in the order starting with the bolt located near the knock pin on the top.

Torque:

39 N*m (400 kgf*cm, 29 ft.*lbf)


HINT:
·

Following the order in the illustration, uniformly tighten the bolts.

·

Move SST up and down, right and left lightly, after checking that the disc is in the center, and tighten the bolts.




Hide 31210 5.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C103828

Using a dial indicator with roller instrument, check the diaphragm spring tip alignment.

Maximum non-alignment:

1.3 mm (0.051 in.)



b.
C103829

If the alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

SST
09333-00013  


Hide 31236B 6.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support onto the transmission.

Torque:

47 N*m (480 kgf*cm, 35 ft.*lbf)



Hide 31232A 7.INSTALL RELEASE BEARING HUB CLIP

Hide 31204 8.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.

Apply release hub grease to the release fork and release bearing assembly contact surfaces, release fork and push rod contact surface and release fork pivot point.

Sealant:

Toyota Genuine Release Hub Grease or Equivalent



b.

Install the release fork onto the release bearing assembly.


Hide 31230 9.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.
C403086E01
0.396,1.844 1.76,2.042 1.365,0.198 10 false Clutch Spline Grease 1.854,0.885 2.052,1.083 0.198,0.198 10 false A

Apply clutch spline grease to the input shaft spline.

Sealant:

Toyota Genuine Clutch Spline Grease or Equivalent


NOTICE:

Do not apply grease to portion A shown in the illustration.



b.

Install the bearing onto the release fork, and then install them onto the transmission.

NOTICE:

After installation, move the fork forward and backward to check that the release bearing slides smoothly.