Home › Drivetrain › M551 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY › 2017.01–2019.08
RM2850E _52 Drivetrain _073187 M551 MANUAL TRANSMISSION / TRANSAXLE _0356150 MANUAL TRANSMISSION ASSEMBLY A

M551 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 33107 1.INSTALL UPPER TRANSMISSION COVER SUB-ASSEMBLY

a.
C147950

Install the upper transmission cover with the 6 bolts.

Torque:

23 N*m (235 kgf*cm, 17 ft.*lbf)



Hide 12321 2.INSTALL NO. 1 ENGINE MOUNTING BRACKET

a.
C147008

Install the No. 1 engine mounting bracket with the 4 bolts.

Torque:

44 N*m (449 kgf*cm, 33 ft.*lbf)



Hide 12325 3.INSTALL NO. 3 ENGINE MOUNTING BRACKET

a.
C147007

Install the No. 3 engine mounting bracket with the 4 bolts.

Torque:

44 N*m (449 kgf*cm, 33 ft.*lbf)



Hide 33110 4.INSTALL MANUAL TRANSMISSION ASSEMBLY

a.
A102492

Install the manual transmission with the 12 bolts.

Torque:

43 N*m (439 kgf*cm, 32 ft.*lbf)



Hide 51204 5.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
A102003

Install the No. 3 frame crossmember with the 4 nuts.

Torque:

56 N*m (571 kgf*cm, 41 ft.*lbf)



b.
A102004

Install the 12 bolts.

Torque:

50 N*m (510 kgf*cm, 37 ft.*lbf)



Hide 6.CONNECT CONNECTOR

a.

Connect the exhaust brake neutral switch connector.


b.

Connect the speed sensor connector.


c.

Connect the back-up light switch connector.


Hide 33827 7.INSTALL NO. 3 TRANSMISSION CONTROL CABLE BRACKET

a.
C147003

Install the No. 3 transmission control cable bracket with the 2 bolts.

Torque:

37 N*m (377 kgf*cm, 27 ft.*lbf)



Hide 33820B 8.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C147949

Connect the 2 cables and install the 2 nuts.

Torque:

15 N*m (153 kgf*cm, 11 ft.*lbf)



b.

Install 2 new clips onto the control cable bracket.


Hide 46503C 9.INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY

a.
C152821

Install the parking brake plate sub-assembly with the 4 bolts.

Torque:

47 N*m (474 kgf*cm, 34 ft.*lbf)



Hide 46501 10.INSTALL PARKING BRAKE DRUM SUB-ASSEMBLY

Hide 37100 12.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

(See Pub. No. RM339E on page PR-7)

Hide 37110B 13.INSTALL PROPELLER SHAFT GUARD (w/ Propeller Shaft Guard)

Hide 14.ADD MANUAL TRANSMISSION OIL

a.
D025304E93
0.313,1.854 1.396,2.063 1.083,0.208 10 false (0 to 0.20 in.) 0.333,1.656 1.198,1.875 0.865,0.219 10 false 0 to 5 mm

Park the vehicle in a level place.


b.

Remove the transmission filler plug and gasket.


c.

Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.

Oil grade:

API GL-4


Viscosity:

SAE 75W-90


Standard capacity:

3.0 liters (3.2 US qts, 2.6 lmp. qts)


NOTICE:
·

Problems may occur when the oil level is too high or too low.

·

After replacing the oil, drive the vehicle and check the oil level again.




d.

Check for oil leakage if the oil level is low.


e.

Install the transmission filler plug and a new gasket.

Torque:

37 N*m (377 kgf*cm, 27 ft.*lbf)



Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

3.9 N*m (40 kgf*cm, 35 in.*lbf)


Hide 16.INSPECT FOR EXHAUST GAS LEAK

Hide 17.INSPECT FOR OIL LEAK