Home › Engine / Hybrid System › N04C-VQ (ENGINE MECHANICAL) › ENGINE UNIT › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073144 N04C-VQ ENGINE MECHANICAL _0355905 ENGINE UNIT A

N04C-VQ ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A146510E09
2.631,1.025 1.874,0.197 false 1.672,0.069 1.859,0.246 0.187,0.177 10 *a

Turn the crankshaft pulley until the groove of the crankshaft damper and the timing mark on the timing gear are aligned.

Text in Illustration
*a Timing Mark


Hide 13901 2.REMOVE NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

a.
A151464E09
1.885,1.083 1.365,1.813 false 1.917,0.927 1.521,0.281 false 1.219,1.802 1.417,2 0.198,0.198 10 false *2 1.375,0.177 1.573,0.375 0.198,0.198 10 false *1

Loosen the lock nuts at the top of the rocker arms and wind up the valve adjusting screws completely.

Text in Illustration
*1 Valve Adjusting Screw
*2 Lock Nut

NOTICE:

If the valve adjusting screws are left unwound, the No. 1 valve rocker shaft sub-assembly may bend when the rocker arm support bolts are loosened.



b.
A151465E01
0.412,0.326 0.516,0.477 0.104,0.152 10 1 1.035,0.326 1.139,0.477 0.104,0.152 10 3 1.657,0.326 1.761,0.477 0.104,0.152 10 5 2.283,0.326 2.388,0.477 0.104,0.152 10 4 2.9,0.326 3.004,0.477 0.104,0.152 10 2

Loosen the rocker arm support bolts in the order shown in the illustration.


c.

Remove the 5 bolts and No. 1 valve rocker shaft sub-assembly.


Hide 13781 3.REMOVE VALVE PUSH ROD

a.

Remove the 8 valve push rods.

NOTICE:

Organize the parts so that each part location can be remembered for reassembly.



Hide 13819 4.REMOVE VALVE BRIDGE

a.

Remove the 8 valve bridges.

NOTICE:

Organize the parts so that each parts location can be remembered for reassembly.



Hide 11101 5.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 13751 7.REMOVE VALVE LIFTER

NOTICE:

Keep the removed parts in the correct order so that they can be returned to their original positions when reassembled.


Hide 13470 8.REMOVE CRANKSHAFT PULLEY ASSEMBLY

a.
A151470

Using a 46 mm socket wrench, remove the nut, crankshaft pulley spacer and crankshaft pulley.

HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the flywheel ring gear of the flywheel assembly to keep it from turning together with the crankshaft.



Hide 11351H 9.REMOVE FLYWHEEL HOUSING STAY RH

a.

Remove the 4 bolts and the flywheel housing stay RH.


Hide 11351G 10.REMOVE FLYWHEEL HOUSING STAY LH

a.

Remove the 4 bolts and the flywheel housing stay LH.


Hide 12101 11.REMOVE OIL PAN SUB-ASSEMBLY

a.

Remove the 26 bolts.


b.
Z004119

Insert the oil pan seal cutter blade between the cylinder block sub-assembly and oil pan sub-assembly. Cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:

Do not damage the contact surface of the cylinder block sub-assembly and oil pan sub-assembly.



Hide 15104 12.REMOVE OIL STRAINER SUB-ASSEMBLY

a.

Remove the 2 bolts and oil strainer sub-assembly.


b.

Remove the O-ring.


Hide 12270 13.REMOVE OIL SEPARATOR ASSEMBLY

a.
A258339

Remove the 5 bolts and the oil separator assembly.


b.

Remove the 3 O-rings.


Hide 11321C 14.REMOVE TIMING GEAR COVER

a.
A254645

Remove the 15 bolts.


b.

Using a screwdriver with its tip wrapped in protective tape, pry out the timing gear cover.

NOTICE:

Do not damage the contact surfaces of the timing gear cover and cylinder block sub-assembly.



Hide 11301C 15.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A254646E02
0.417,0.51 0.604,0.51 0.604,0.51 1.115,0.729 true 1.427,0.719 1.688,0.177 1.688,0.177 1.854,0.177 true 2.552,1.75 3.083,1.75 false 2.906,1.583 2.99,1.583 2.99,1.583 2.99,1.75 false 1.865,0.083 2.073,0.25 0.208,0.167 10 false *a 0.25,0.417 0.458,0.583 0.208,0.167 10 false *b 3.146,1.656 3.354,1.823 0.208,0.167 10 false *c

Using a screwdriver with its tip wrapped in protective tape, pry out the front crankshaft oil seal.

Text in Illustration
*a Cloth
*b Protective Tape
*c Wooden Block

HINT:

Use wooden blocks and cloth to prevent the contact surfaces and the timing gear cover from being damaged.



Hide 16.INSPECT NO. 2 IDLE GEAR THRUST CLEARANCE

a.
A151473

Using a feeler gauge, measure the thrust clearance between the No. 2 idle gear thrust plate and No. 2 idle gear sub-assembly.

Standard thrust clearance:

0.103 to 0.164 mm (0.00406 to 0.00646 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the No. 2 idle gear thrust plate and No. 2 idle gear sub-assembly.


Hide 17.INSPECT NO. 2 IDLE GEAR BACKLASH

a.
A157096

Using a dial indicator, measure the backlash between the No. 1 idle gear sub-assembly and No. 2 idle gear sub-assembly.

Standard backlash:

0.036 to 0.166 mm (0.00144 to 0.00654 in.)


Maximum backlash:

0.30 mm (0.0118 in.)


If the backlash is more than the maximum, replace the No. 1 idle gear sub-assembly and No. 2 idle gear sub-assembly.


Hide 13572C 18.REMOVE NO. 2 IDLE GEAR THRUST PLATE

a.
A261333

Remove the 2 bolts and No. 2 idle gear thrust plate.


Hide 13508N 19.REMOVE NO. 2 IDLE GEAR SUB-ASSEMBLY

a.
A272253

Remove the No. 2 idle gear sub-assembly from the No. 2 idle gear shaft.


Hide 13581C 20.REMOVE NO. 2 IDLE GEAR SHAFT

a.

Remove the 2 bolts and No. 2 idle gear shaft.


b.

Remove the O-ring.


Hide 13577D 21.REMOVE LOCK PLATE

a.

Remove the 3 bolts and lock plate from the front end plate.


Hide 22.INSPECT CAMSHAFT TIMING GEAR BACKLASH

a.
A151477

Using a dial indicator, measure the backlash between the camshaft timing gear and No. 1 idle gear sub-assembly.

Standard backlash:

0.068 to 0.171 mm (0.00268 to 0.00673 in.)


Maximum backlash:

0.30 mm (0.0118 in.)


If the backlash is more than the maximum, replace the camshaft timing gear and No. 1 idle gear sub-assembly.


Hide 13501 23.REMOVE CAMSHAFT SUB-ASSEMBLY

Hide 24.INSPECT OIL PUMP GEAR BACKLASH

a.
A157097

Using a dial indicator, measure the backlash between the oil pump gear and No. 1 idle gear sub-assembly.

Standard backlash:

0.065 to 0.181 mm (0.00256 to 0.00713 in.)


Maximum backlash:

0.30 mm (0.0118 in.)


If the backlash is more than the maximum, replace the pump and No. 1 idle gear sub-assembly.


Hide 25.INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE

a.
A151479

Using a feeler gauge, measure the thrust clearance between the No. 1 idle gear thrust plate and No. 1 idle gear sub-assembly.

Standard thrust clearance:

0.103 to 0.164 mm (0.00406 to 0.00646 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the No. 1 idle gear thrust plate and No. 1 idle gear sub-assembly.


Hide 26.INSPECT NO. 1 IDLE GEAR BACKLASH

a.

Using a dial indicator, measure the backlash between the crankshaft gear and No. 1 idle gear sub-assembly.

Standard backlash:

0.035 to 0.162 mm (0.00138 to 0.00638 in.)


Maximum backlash:

0.30 mm (0.0118 in.)


If the backlash is more than the maximum, replace the crankshaft gear and No. 1 idle gear sub-assembly.


Hide 13581B 27.REMOVE NO. 1 IDLE GEAR SHAFT

a.

Remove the bolt.


b.
A151481E01
1.762,1.786 2.057,1.932 0.295,0.146 10 SST 1.706,1.31 1.932,1.752 1.932,1.752 2.206,1.195 false 1.93,1.293 1.932,1.752 false

Using SST, remove the No. 1 idle gear shaft.

SST
09910-00015  (09911-00011, 09912-00010)

NOTICE:

When removing the No. 1 idle gear shaft, hold the No. 1 idle gear sub-assembly to prevent the No. 1 gear sub-assembly and No. 1 idle gear thrust plate from falling.



Hide 13508M 28.REMOVE NO. 1 IDLE GEAR SUB-ASSEMBLY

a.

Remove the No. 1 idle gear sub-assembly.


Hide 13572B 29.REMOVE NO. 1 IDLE GEAR THRUST PLATE

a.

Remove the No. 1 idle gear thrust plate.


Hide 13521B 30.REMOVE CRANKSHAFT GEAR

a.
A429561E01
1.25,0.802 1.469,1.177 true 0.49,0.917 0.802,1.115 0.313,0.198 10 false *a 1.771,1.698 1.979,1.885 0.208,0.188 10 false *b 1.073,0.615 1.417,0.813 0.344,0.198 10 false SST

Using SST, remove the crankshaft gear.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051)

Text in Illustration
*a Hold
*b Turn Clockwise


Hide 15100 31.REMOVE OIL PUMP ASSEMBLY

a.

Remove the 7 bolts and oil pump.


b.

Remove the gasket from the oil pump.


Hide 11311H 32.REMOVE FRONT END PLATE

a.
A151485

Remove the 4 bolts and front end plate.


Hide 11312 33.REMOVE FRONT END PLATE GASKET

a.

Remove the front end plate gasket from the front end plate.


Hide 13450A 34.REMOVE FLYWHEEL ASSEMBLY

a.
A151486

Temporarily install 4 bolts in the positions of the cylinder block sub-assembly shown in the illustration to prevent the wires from sliding toward the center of the cylinder block sub-assembly.


b.

Attach 2 wires to the cylinder block sub-assembly.

HINT:

The wires must be attached to the outside of the installed bolts.



c.

Using a chain block and an engine sling device, remove the cylinder block sub-assembly from the engine stand.


d.
A151487E05
0.708,2.292 1.25,2.667 1.25,2.667 1.781,2.313 true 2.427,1.115 2.573,0.594 2.573,0.594 2.74,0.594 false 2.74,0.479 2.969,0.698 0.229,0.219 10 false *1 1.167,2.656 1.396,2.875 0.229,0.219 10 false *a

Place the cylinder block sub-assembly on wooden blocks on a workbench.

Text in Illustration
*1 Flywheel Housing
*a Wooden Block


e.

Remove the 4 bolts.


f.
A151470

Insert a screwdriver through the inspection hole of the flywheel housing into the flywheel ring gear of the flywheel assembly to keep it from turning together with the crankshaft.


g.
A265498E01
1.678,0.768 1.791,0.931 0.113,0.163 10 1 1.678,2.471 1.791,2.634 0.113,0.163 10 2 0.865,1.626 0.978,1.789 0.113,0.163 10 3 2.515,1.626 2.628,1.789 0.113,0.163 10 4 1.14,1.059 1.253,1.222 0.113,0.163 10 5 2.24,1.059 2.353,1.222 0.113,0.163 10 8 1.122,2.193 1.235,2.356 0.113,0.163 10 7 2.222,2.193 2.335,2.356 0.113,0.163 10 6

Uniformly loosen and remove the 8 bolts in the order shown in the illustration.


h.

Remove the flywheel assembly.

NOTICE:

The flywheel assembly is heavy. When removing, be careful not to drop it.



Hide 13453 35.REMOVE FLYWHEEL RING GEAR

a.
A151489

Using a torch, heat the flywheel ring gear evenly to approximately 200°C (392°F).

CAUTION:

Do not touch the flywheel ring gear and flywheel assembly while they are hot.


NOTICE:

Be careful not to overheat the flywheel ring gear.



b.
A151490

Using a brass bar and hammer, uniformly strike all around the flywheel ring gear and remove the flywheel gear.

CAUTION:

After removing, allow the flywheel ring gear to cool before handling.



Hide 11351 36.REMOVE FLYWHEEL HOUSING

a.

Remove the 10 bolts.


b.

Using a screwdriver with its tip wrapped in protective tape, pry off the flywheel housing.


Hide 11381A 37.REMOVE REAR ENGINE OIL SEAL

a.
A151491E10
0.292,2.156 0.479,2.875 0.479,2.875 0.865,2.729 true 1.688,1.51 2.688,0.271 true 1.594,1.875 2.26,2.813 true 2.208,2.844 2.375,2.99 0.167,0.146 10 false *b 0.365,2.917 0.573,3.094 0.208,0.177 10 false *c 2.719,0.167 2.906,0.344 0.188,0.177 10 false *a

Using a screwdriver with its tip wrapped in protective tape, pry out the rear engine oil seal.

Text in Illustration
*a Protective Tape
*b Cloth
*c Wooden Block

HINT:

Use wooden blocks and a piece of cloth to prevent damage to the flywheel housing.



Hide 38.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A151513

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.200 to 0.520 mm (0.00787 to 0.0205 in.)


Maximum thrust clearance:

0.60 mm (0.0236 in.)


If the thrust clearance is more than the maximum, replace the connecting rod. If necessary, replace the crankshaft.


Hide 13301A 39.REMOVE PISTON WITH CONNECTING ROD

a.

Remove the piston with connecting rod from the cylinder block sub-assembly.


Hide 13260 40.REMOVE CONNECTING ROD SUB-ASSEMBLY

Hide 13202 41.REMOVE CONNECTING ROD BEARING SET

Hide 11462 42.REMOVE CYLINDER LINER

NOTICE:

When reusing the cylinder liner, misalignment with the cylinder block sub-assembly may concentrate stress on the thin part of the cylinder liner and it may break.


HINT:
A151515E11
2.065,1.377 2.249,1.54 0.184,0.163 10 *a

Before removing the cylinder liner, put matchmarks on the cylinder liner and cylinder block sub-assembly.

Text in Illustration
*a Matchmarks


a.
A151516E01
0.445,0.608 0.743,0.761 0.299,0.153 10 SST 1.258,0.814 0.813,0.693 false

Using SST, remove the cylinder liner.

SST
S0942-01460  

NOTICE:

Keep the removed parts in the correct order so that they can be returned to their original positions when reassembled.


HINT:

Organize the parts so that each parts location can be remembered for reassembly.



Hide 43.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A151519

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth.

Standard thrust clearance:

0.050 to 0.220 mm (0.00197 to 0.00866 in.)


Maximum thrust clearance:

0.40 mm (0.0157 in.)


If the thrust clearance is more than the maximum, replace the crankshaft thrust washer set. If necessary, replace the crankshaft.


Hide 13411 44.REMOVE CRANKSHAFT

a.
A151520E01
2.902,0.104 3.011,0.253 0.109,0.149 10 2 2.959,0.778 2.959,0.291 false 2.368,0.104 2.478,0.253 0.109,0.149 10 6 2.425,0.778 2.425,0.291 false 1.786,0.104 1.958,0.253 0.172,0.149 10 10 1.877,0.778 1.877,0.291 false 1.274,0.104 1.383,0.253 0.109,0.149 10 8 1.331,0.778 1.331,0.291 false 0.74,0.104 0.849,0.253 0.109,0.149 10 4 2.901,1.906 3.01,2.056 0.109,0.149 10 1 2.368,1.906 2.477,2.056 0.109,0.149 10 5 1.837,1.906 1.949,2.056 0.113,0.149 10 9 1.273,1.906 1.382,2.056 0.109,0.149 10 7 0.739,1.906 0.848,2.056 0.109,0.149 10 3 0.797,0.778 0.797,0.291 false 0.797,1.394 0.797,1.881 false 1.33,1.394 1.33,1.881 false 1.878,1.394 1.878,1.881 false 2.425,1.394 2.425,1.881 false 2.959,1.394 2.959,1.881 false

Remove the 10 crankshaft bearing cap bolts in the order shown in the illustration.


b.

Using a plastic-faced hammer, tap the crankshaft bearing caps to remove them.

NOTICE:

Be careful not to damage the crankshaft thrust washers and bearings.



c.

Remove the crankshaft.


Hide 11011 45.REMOVE CRANKSHAFT THRUST WASHER SET

HINT:

Organize the parts so that each parts location can be remembered for reassembly.


Hide 11702 46.REMOVE CRANKSHAFT BEARING SET

HINT:

Organize the parts so that each parts location can be remembered for reassembly.


Hide 11271A 47.REMOVE REAR CYLINDER BLOCK COVER

a.
A155757

Remove the 2 bolts, rear cylinder block cover and O-ring.


Hide 15605 48.REMOVE OIL CHECK VALVE SUB-ASSEMBLY

a.

Remove the bolt, the oil check valve sub-assembly and gasket.


Hide 15708 49.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Remove the bolt and the No. 1 oil nozzle sub-assembly.


Hide 13011 50.REMOVE PISTON RING SET

a.
A151521

Using a piston ring expander, remove the piston rings.

HINT:

Arrange the piston rings in the correct order.



Hide 13101A 51.REMOVE PISTON PIN HOLE SNAP RING

a.
A151522

Using snap ring pliers, remove the snap rings.


Hide 52.REMOVE PISTON

a.

Gradually heat the piston to approximately 50°C (122°F).


b.
A151524

Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and pin are a set.

·

Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.




Hide 13201A 53.REMOVE CONNECTING ROD SMALL END BUSH

a.
A151666E10
0.896,0.625 1.198,1.313 false 0.5,1.698 0.25,2.469 false 2.25,1.646 2.073,2.021 false 1.969,2.063 2.208,2.281 0.24,0.219 10 false *3 0.156,2.49 0.396,2.708 0.24,0.219 10 false *2 0.771,0.438 1.01,0.656 0.24,0.219 10 false *1

Prepare SST.

i.

Install SST (press sub-assembly) to SST (guide) by inserting the pin of SST (press sub-assembly) into SST (guide), and then secure them together by installing SST (wing nut).

SST
S0940-21450  
S0948-11130  
S9233-10360  

Text in Illustration
*1 SST (Guide)
*2 SST (Press Sub-assembly)
*3 SST (Wing Nut)

HINT:

Orient SST (guide) so that the letter W, which is stamped on SST (guide), is above the pin.



ii.
A151536E11
2.719,1.49 2.646,1.74 false 1.052,1.365 0.958,1.729 false 2.052,0.833 1.76,0.344 false 2.552,1.75 2.813,1.979 0.26,0.229 10 false *3 0.865,1.75 1.125,1.979 0.26,0.229 10 false *2 1.656,0.167 1.917,0.396 0.26,0.229 10 false *1

Set SST (guide) and SST (press sub-assembly) on a level surface.

Text in Illustration
*1 Connecting Rod
*2 SST (Guide)
*3 SST (Press Sub-assembly)



b.

Using SST, remove the bush.

i.

Set the connecting rod assembled without the connecting rod bearing on SST (guide) and SST (press sub-assembly).


ii.
A151537E06
2.125,0.677 2.51,0.542 false 2.104,1.188 2.51,1.042 false 2.219,1.438 2.49,1.531 false 1.927,2.219 2.198,2.531 false 0.906,1.594 1.552,1.354 false 1.594,0.792 0.906,0.542 false 2.208,2.531 2.375,2.719 0.167,0.188 10 false *6 2.542,1.469 2.708,1.656 0.167,0.188 10 false *5 2.542,0.948 2.708,1.135 0.167,0.188 10 false *4 2.542,0.427 2.708,0.615 0.167,0.188 10 false *3 0.719,1.5 0.885,1.688 0.167,0.188 10 false *2 0.719,0.438 0.885,0.625 0.167,0.188 10 false *1

Install SST (spindle) to the connecting rod bush.

SST
S0940-21470  

Text in Illustration
*1 Groove
*2 Oil Hole
*3 SST (Spindle)
*4 Bush
*5 Connecting Rod
*6 SST (Press Sub-assembly)

HINT:

Align the groove of SST (spindle) with the oil hole of the bush.



iii.
A151538E05
1.686,1.067 1.279,0.659 false 2.293,0.707 1.999,0.413 false 1.113,0.461 1.321,0.669 0.208,0.208 10 *1 2.496,0.242 2.704,0.45 0.208,0.208 10 *a 1.809,0.242 2.017,0.45 0.208,0.208 10 *2

Using a press, remove the bush.

Text in Illustration
*1 Connecting Rod
*2 SST (Spindle)
*a Press

HINT:

Always operate the press slowly and smoothly.




Hide 54.REMOVE CAMSHAFT BEARING

a.
A151660E06
0.552,1.594 0.552,1.333 false 0.771,0.458 0.99,0.656 0.219,0.198 10 false *a 0.385,1.615 0.677,1.76 0.292,0.146 10 false SST 1.719,0.469 1.917,0.646 0.198,0.177 10 false *b 2.688,0.458 2.885,0.635 0.198,0.177 10 false *c

Using SST, remove the camshaft bearings in the directions indicated by the arrow marks in the illustration.

SST
09215-00101  (09215-00130, 09215-00141, 09215-00150, 09215-00161)
09215-00013  (09215-00021, 09215-00461)

Text in Illustration
*a No. 1 Crankshaft Bearing
*b No. 2 Crankshaft Bearing
*c No. 3 Crankshaft Bearing
V100135

Front

NOTICE:

Remove the No. 1 crankshaft bearing, No. 2 crankshaft bearing and No. 3 crankshaft bearing in that order.