Home › Engine / Hybrid System › N04C-VQ (LUBRICATION) › OIL AND OIL FILTER › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073148 N04C-VQ LUBRICATION _0355934 OIL AND OIL FILTER A

N04C-VQ LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will cause the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants that may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

·

For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 51441D 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51445D 2.REMOVE ENGINE UNDER COVER BRACKET RH

Hide 51446C 3.REMOVE ENGINE UNDER COVER BRACKET LH

Hide 4.REMOVE ENGINE SERVICE HOLE MAIN COVER

Hide 5.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the drain plug and gasket from the oil pan and drain the engine oil into a container.


c.

Clean the drain plug.


d.

Install the drain plug with a new gasket.

Torque:

41 N*m (418 kgf*cm, 30 ft.*lbf)



Hide 6.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A388375E02
1.208,1.052 1.604,1.052 false 0.906,0.99 1.24,1.177 0.333,0.188 10 true SST

Using SST, remove the oil filter sub-assembly.

SST
S0955-31030  


Hide 7.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Clean the oil filter sub-assembly installation surface.


b.

Apply engine oil to the oil filter gasket.


c.

Lightly screw the oil filter sub-assembly to the engine until the oil filter sub-assembly does not turn.

A388376E02
3.875,1.333 4.323,1.344 false 3.552,1.26 3.865,1.458 0.313,0.198 10 true SST


d.

Using SST, tighten the oil filter sub-assembly an additional 2/3 turn.

SST
S0955-31030  

Torque:

20 N*m (200 kgf*cm, 14 ft.*lbf)



Hide 8.ADD ENGINE OIL

a.

Add fresh oil and install the oil filler cap sub-assembly.

Engine oil:
Oil Grade Oil Viscosity (SAE)
·

API (CI-4, CI-4 PLUS or CJ-4)

·

ACEA (E-4, E-6, E-7 or E-9)

·

API CJ-4, ACEA E-6, E-9 is preferred


·

10W-30

·

15W-40




Capacity:
Item Fill amount
Drain and refill with oil filter change 7.7 L (8.1 US qts, 6.8 Imp. qts)
Drain and refill without oil filter change 6.3 L (6.7 US qts, 5.5 Imp. qts)
Dry fill 8.4 L (8.9 US qts, 7.4 Imp. qts)



Hide 9.INSPECT FOR OIL LEAK

a.

Warm up the engine and check for engine oil leaks.


Hide 10.INSTALL ENGINE SERVICE HOLE MAIN COVER

Hide 51446C 11.INSTALL ENGINE UNDER COVER BRACKET LH

Hide 51445D 12.INSTALL ENGINE UNDER COVER BRACKET RH

Hide 51441D 13.INSTALL NO. 1 ENGINE UNDER COVER