Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2850E _51 Engine / Hybrid System _073150 1HZ ENGINE MECHANICAL _0355948 CYLINDER BLOCK A

1HZ ENGINE MECHANICAL  CYLINDER BLOCK  PISTON AND CONNECTING ROD INSPECTION  


PROCEDURE

Hide 1.CLEAN PISTON

a.
A422422

Using a gasket scraper, remove the carbon from the piston top.


b.
A422423

Using a groove cleaning or broken ring, clean the piston ring grooves.


c.
A422424

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 2.INSPECT PISTON PIN FIT

a.
A422431

At 80°C (176°F), you should be able to push the piston pin into the piston pin hole with your thumb.


Hide 3.INSPECT CONNECTING ROD

a.

Inspect connecting rod alignment

·
A422432


·

Check for bending.


Maximum bending:

0.03 mm (0.0012 in.) per 100 mm (3.94 in.)


If bent is greater than maximum, replace the connecting rod assembly.

·
A422433


·

Check for twist.


Maximum twist:

0.15 mm (0.0059 in.) per 100 mm (3.94 in.)


If twist is greater than maximum, replace the connecting rod assembly.


b.
A422434

Inspect connecting rod bolts

Using vernier calipers, measure the minimum diameter of the compressed bolt at the measuring point.

Standard diameter:

8.300 - 8.400 mm (0.3268 - 0.3307 in.)


Minimum diameter:

7.95 mm (0.3130 in.)


If the diameter is less than minimum, replace the connecting rod bolt.


c.

Inspect piston pin oil clearance

i.
A422435

Using a caliper gauge, measure the inside diameter of the connecting rod bushing.

Bushing inside diameter:
1PZ and 1HZ:

29.008 - 29.020 mm (1.1420 - 1.1425 in.)

1HD-T:

33.008 - 33.020 mm (1.2995 - 1.3000 in.)



ii.
A422436

Using a micrometer, measure the piston pin diameter.

Piston pin diameter:
1PZ and 1HZ:

29.000 - 29.012 mm (1.1417 - 1.1422 in.)

1HD-T:

33.000 - 33.012 mm (1.2992 - 1.2997 in.)



iii.

Subtract the piston pin diameter measurement from the bushing inside diameter measurement.

Standard oil clearance:

0.004 - 0.012 mm (0.0002 - 0.0005 in.)


Maximum oil clearance:

0.03 mm (0.0012 in.)




Hide 4.IF NECESSARY, REPLACE CONNECTING ROD BUSHING

a.
A422437

A422438

Remove connecting rod bushings

Using SST and a press, press out the bushing.

1PZ and 1HZ

SST
09222-66010  

1HD-T

SST
09222-17011  (09222-05020, 09222-05040)


b.

Install new connecting rod bushings

i.
A422439

Using a round file, lightly file off any roughness from the small end of the connecting rod.


ii.
A422440

(1HD-T)

Attach the bushing to SST with the ball of SST inside the oil hole of the bushing.


iii.
A422441

A422442

Align the oil holes of the bushing and connecting rod.


iv.
A422443

A422444

Using SST and a press, press in the bushing.

1PZ and 1HZ

SST
09222-66010  

1HD-T



c.

Hone connecting rod bushing and check piston pin fit

i.
A422445

Using a pin hole grinder, hone the bushing to obtain the standard specified clearance between the bushing and piston pin.

Click hereEngine / Hybrid System>1HZ (ENGINE MECHANICAL)>CYLINDER BLOCK>PISTON AND CONNECTING ROD INSPECTION


ii.
A422446

Check the piston pin fit at normal room temperature. Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.