Home › Engine / Hybrid System › 1HZ FUEL › FUEL INJECTION PUMP
RM2850E _51 Engine / Hybrid System _073151 1HZ FUEL _0355954 FUEL INJECTION PUMP A

1HZ FUEL  FUEL INJECTION PUMP  DISASSEMBLY  


PROCEDURE

Hide 1. MOUNT PUMP ASSEMBLY TO SST (STAND)

A422798

SST
09241-76022  09245-54010  

Hide 2.REMOVE SET KEY OF DRIVE PULLEY FROM DRIVE SHAFT

Hide 3.REMOVE IDLE-UP ACTUATOR (w/ A/C)

Hide 4.REMOVE TWO FUEL PIPES

a.
A422799

Place the matchmarks on the fuel inlet pipe and governor cover.


Hide 5.REMOVE IDLE-UP LEVER (w/ ACSD)

a.
A422800

Using a 5 mm hexagon wrench, remove the three bolts and idle-up lever.


Hide 6.REMOVE THERMO WAX (w/ ACSD)

a.
A422801

Using a screwdriver, turn the cold starting lever counterclockwise approx. 20°.


b.

Put a metal plate (thickness of 3.5 -7.5 mm) (0.138 -0.295 in.) between the cold starting lever and thermo wax plunger.


c.
A422802

Using a 5 mm hexagon wrench, remove the two bolts, thermo wax and O-ring.


Hide 7.REMOVE PCS ACTUATOR (w/ PCS)

a.
A422803

Remove the PCS adjusting screw.


b.

Remove the clip.


c.
A422804

Using a 5 mm hexagon wrench, remove the two bolts and PCS actuator assembly.


Hide 8.REMOVE NO.1 PCS LEVER (w/ PCS)

a.
A422805

Remove the nut and No.1 PCS lever.


Hide 9.REMOVE DASH POT (w/ Dash Pot)

a.
A422806

Remove the dash pot and gasket.


Hide 22390A 10.REMOVE FUEL CUT SOLENOID

a.

Disconnect the lead wire connector from the bracket.


b.

Disconnect the dust cover from the fuel cut solenoid.


c.
A422807

Remove the nut, lead wire and dust cover.


d.
A422808

Remove the fuel cut solenoid, O-ring, spring, valve, strainer and wave washer.


Hide 11.REMOVE PICKUP SENSOR (w/ TACHOMETER)

a.
A422809

Remove the pickup sensor and O-ring.


Hide 22701 12.REMOVE ADJUSTING LEVER

a.
A422810

Place the matchmarks on adjusting lever and shaft.


b.
A422811

Remove the nut, return spring guide, adjusting lever and return spring.


Hide 22703A 13.REMOVE GOVERNOR COVER

a.

(w/ HAC and 1HD-T)

Remove the idle speed adjusting screw.


b.
A422812

Using a 5 mm hexagon wrench, remove the four bolts.


c.
A422813

Disconnect the speed control spring from the spring seat, and remove the spring seat, damper spring, speed control spring, the governor cover and adjusting lever shaft assembly and gasket.


Hide 14.REMOVE GOVERNOR ADJUSTING LEVER SHAFT FROM GOVERNOR COVER

a.
A422814

Remove the following parts from the governor cover.

Text in Illustration
(1) Adjusting lever shaft, O-ring and washer assembly
(2) O-ring
(3) Washer


Hide 15.DISASSEMBLE HIGH ALTITUDE COMPENSATOR (1PZ (w/ HAC) and 1HZ (w/ HAC))

a.
A422815

Remove the bolt, gasket and lever control spring.

i.

Remove lever control spring



b.
A422816

Remove pneumatic bellows

i.

Using a 5 mm hexagon wrench, remove the four bolts.


ii.
A422817

Remove the following parts:

Text in Illustration
(1) Pneumatic bellows cover
(2) Gasket
(3) Shims
NOTICE:

Note the number of the shims.


(4) Pneumatic bellows
(5) Two rubber caps
(6) Push rod
(7) Pneumatic bellows spring



c.

Remove control lever

i.
A422818

Using a 4 mm hexagon wrench, remove the two bolts and gaskets.


ii.
A422819

Using a small screwdriver, push out the support pin and remove the control lever.


iii.
A422820

Using needle nose pliers, remove the connecting pin.

NOTICE:

Be careful not to damage the connecting.

Tape the tip of the pliers.




Hide 16.DISASSEMBLE BOOST COMPENSATOR (1HD-T)

a.
A422821

Remove lever control spring

i.

Remove the bolt, gasket and lever control spring.



b.

Remove boost compensator diaphragm

i.
A422822

Using a 5 mm hexagon wrench, remove the four bolts.


ii.
A422823

Remove the following parts:

Text in Illustration
(1) Diaphragm cover
(2) Diaphragm
(3) Spring
(5) Boost compensator shim



c.
A422824

Remove guide bushing


d.

Remove control lever

i.
A422825

Using a 4 mm hexagon wrench, remove the two bolts and gaskets.


ii.
A422826

Using a small screwdriver, push out the support pin and remove the control lever.


iii.
A422827

Using needle nose pliers, remove the connecting pin.

NOTICE:

Be careful not to damage the connecting pin. Tape the tip of the pliers.




e.

Remove No.2 PCS lever

i.
A422828

Remove the following pars from the the governor cover.

Text in Illustration
(1) No.2 lever, O-ring and washer assembly
(2) O-ring
(3) Washer



f.

Remove No.2 overflow screw

i.
A422829

Remove No.2 overflow screw Remove the cover and No.2 overflow screw.



Hide 17.CHECK FLYWEIGHT HOLDER THRUST CLEARANCE

Click hereEngine / Hybrid System>1HZ FUEL>FUEL INJECTION PUMP>REASSEMBLY

Thrust clearance:

0.15 - 0.35 mm (0.0059 - 0.0138 in.)


Hide 18.REMOVE GOVERNOR SHAFT AND FLYWEIGHT HOLDER

a.
A422830

Remove the governor shaft lock nut by turning it clockwise.

NOTICE:

The governor shaft and lock nut have LH threads.



b.
A422831

Using a 5 mm hexagon wrench, remove the governor shaft clockwise, and remove the following part:

Text in Illustration
(1) Flyweight holder assembly
(2) No.1 flyweight washer
(3) Governor gear adjusting washer

HINT:

Be careful not to drop the two washers into the pump housing.



c.
A422832

Remove the following parts from the flyweight holder.

Text in Illustration
(1) Governor sleeve
(2) No.2 flyweight washer
(3) Four flyweights


Hide 22811 19.REMOVE INJECTION PUMP STAY

a.
A422833

Using a 5 mm hexagon wrench, remove the three bolts and stay.


Hide 22176 20.REMOVE DISTRIBUTIVE HEAD PLUG

a.
A422834

Using SST, remove the distributive head plug.

SST
09260-54012  (09262-54010)


Hide 21.REMOVE DELIVERY VALVE HOLDERS

a.
A422835

Using SST, remove the delivery valve holders, springs and spring seats.

SST
09260-54012  (09269-54020)


b.
A422836

Remove the delivery valves and gaskets.

NOTICE:

Do not touch the sliding surfaces of the delivery valve with your hand.


HINT:
A422837

A422838

Arrange the delivery valves, springs, spring seats and holders in order.



Hide 22.REMOVE DISTRIBUTIVE HEAD

a.
A422839

Using a 5 mm hexagon wrench, remove the four bolts.


b.
A422840

Remove the distributive head and following parts:

Text in Illustration
(1) Two lever support springs
(2) Two plunger spring guides
(3) Two plunger spring shims
(4) Two upper spring seats
(5) Two plunger springs


Hide 23.REMOVE PUMP PLUNGER

a.
A422841

Using SST, remove the pump plunger and plunger adjusting shim together with the following parts:

Text in Illustration
(1) Spill ring
(2) Lower spring seat
(3) Upper plunger plate
(4) Lower plunger plate

SST
09260-54012  (09269-54030)

NOTICE:
A422842

Do not touch the sliding surfaces of the pump plunger with your hand.



Hide 24.REMOVE GOVERNOR LINK

a.
A422843

Using SST, remove the two support bolts, gaskets and governor link.

SST
09260-54012  09269-54040  


Hide 25.REMOVE FACE CAM PLATE AND COUPLING

a.
A422844

Remove the face camplate, spring and coupling.


Hide 26.REMOVE ROLLER RING AND DRIVE SHAFT

a.
A422845

Remove the timer clip and stopper pin.


b.
A422846

Push the slide pin toward inside.


c.
A422847

A422848

A422849

(1PZ)

Push the drive shaft, and remove the roller ring, three rollers and shims assembly.

(1HZ and 1HD-T)

Push the drive shaft, and remove the roller ring, four rollers and shims assembly.

NOTICE:
·

Be careful not to drop the rollers.

·

Do not alter the position or assembly of the rollers.




d.
A422850

Remove the drive shaft, governor drive gear, two joint rubbers assembly, set key and drive shaft washer.


e.
A422851

Remove the drive gear and two joint rubbers from the drive shaft.


Hide 27.REMOVE TIMER

a.
A422852

Using a 5 mm hexagon wrench, remove the four bolts.


b.
A422853

Remove the following parts:

Text in Illustration
(1) LH timer cover, timer adjusting screw and nut assembly
(2) Spring
(3) O-ring
(4) RH timer cover
(5) O-ring
(6) Piston
(7) Sub-piston


c.

Remove the nut from the LH timer cover.


d.
A422854

Using a 5 mm hexagon wrench, remove the timer adjusting screw.


e.

Remove the O-ring from the timer adjusting ring.


Hide 22505 28.REMOVE FUEL FEED PUMP

a.

Remove the two screws.


b.
A422855

Using a piece of wire, remove the feed pump cover.


c.

Remove the feed pump rotor, four blades and liner.

NOTICE:
·

Be careful not to interchange the blade positions.

·

Be careful not to damage the pump body.




Hide 22180 29.REMOVE REGULATOR VALVE

a.
A422856

Using SST, remove the regulator valve and two O-rings.

SST
09260-54012  (09262-54020)


Hide 30.REMOVE FUEL INLET HOLLOW SCREW

a.
A422857

Remove the hollow screw and gasket.