Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › DRIVE BELT
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356000 DRIVE BELT A

N04C-VL ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.

Install the fan and generator V belt.


b.
A146502E04
2.167,1.25 1.76,1.26 false 2.177,1.25 1.76,1.26 false 2.406,1.25 2.625,0.979 false 1.573,1.167 1.729,1.302 0.156,0.135 10 false *1 2.635,0.885 2.833,1.073 0.198,0.188 10 true *2

Turn the adjusting bolt and adjust the tension of the fan and generator V belt.

Text in Illustration
*1 Fixing Bolt
*2 Adjusting Bolt


c.

Tighten the fixing bolt.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



d.

Tighten the adjusting bolt.

Torque:

6.0 N*m (61 kgf*cm, 53 in.*lbf)



Hide 88310A 2.INSTALL NO. 1 V BELT (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) (w/ Air Conditioning System)

a.

Install the No. 1 V belt (cooler compressor tocrankshaft pulley).


b.
A146501E03
1.75,1.302 1.938,1.948 false 1.552,0.865 0.5,0.573 false 1.875,1.969 2.031,2.115 0.156,0.146 10 false *1 0.302,0.479 0.458,0.625 0.156,0.146 10 false *2

Turn the adjusting bolt and adjust the tension of the No. 1 V belt (cooler compressor to crankshaft pulley).

Text in Illustration
*1 Fixing Bolt
*2 Adjusting Bolt


c.

Tighten the fixing bolt.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



d.

Tighten the adjusting bolt.

Torque:

15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide 16361A 3.INSPECT FAN AND GENERATOR V BELT

a.
A103003

Check the fan and generator V belt deflection and tension.

HINT:

The specified deflection and tension values per belt are shown in the following table.


Standard Deflection (Pressing force: 98 N (10 kg, 22.0 lb)):
Item Specified Condition
New belt 10.5 to 12.5 mm (0.413 to 0.492 in.)
Used belt 12 to 13 mm (0.472 to 0.512 in.)


Standard Tension:
Item Specified Condition
New belt 350 to 500 N (36 to 51 kg, 79 to 112 lb)
Used belt 300 to 400 N (31 to 41 kg, 67 to 90 lb)


Text in Illustration
V100135

Measuring Point

NOTICE:
·

Make sure not to tighten the fan and generator V belt higher than the specified tension. When the fan and generator V belt is overtightened, the lifespan of the fan and generator V belt is reduced.

·

If the fan and generator V belt deflection amount is 15 mm or more (tension 150 N (15 kg, 34 lb)), the fan and generator V belt may slip. Therefore, readjust the fan and generator V belt to the tension specified for "Used belt". (Frequent readjustment of the fan and generator V belt reduces the lifespan of the fan and generator V belt.)

·

Check that there are no cracks and damage on the fan and generator V belt. If there are any abnormalities, replace the part.



HINT:

The fan and generator V belt tension decreases after the vehicle has been driven, but since this occurs during the initial break-in period, this is not a malfunction.



Hide 88310A 4.INSPECT NO. 1 V BELT (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) (w/ Air Conditioning System)

a.
A146591

Check the No. 1 V belt (cooler compressor to crankshaft pulley) deflection and tension.

HINT:

The specified deflection and tension values per belt are shown in the following table.


Standard Deflection (Pressing force: 98 N (10 kg, 22.0 lb)):
Item Specified Condition
New belt 8.6 to 10.6 mm (0.339 to 0.417 in.)
Used belt 10.7 to 12.1 mm (0.421 to 0.476 in.)


Standard Tension:
Item Specified Condition
New belt 404 to 576 N (41 to 59 kg, 91 to 129 lb)
Used belt 294 to 392 N (30 to 40 kg, 66 to 88 lb)


Text in Illustration
V100135

Measuring Point

NOTICE:
·

Check the No. 1 V belt (cooler compressor to crankshaft pulley) deflection at the specified point.

·

When installing a new belt, set its tension to the specified value.

·

When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.




Hide 51441D 5.INSTALL NO. 1 ENGINE UNDER COVER