Wear protective gloves. Sharp areas on the parts may injure your hands.
The procedure listed below is for 1st row to 7th row for long body, and 1st row to 6th row for standard body.
The procedure listed below is a representative example.
Use the same procedure for all rows, unless otherwise specified.
1.REMOVE SUB SEAT ASSEMBLY (w/ Sub Seat)
71811C
2.REMOVE RECLINING ADJUSTER COVER RH
Remove the 2 screws.
for 1-leg Type, 7th Row Seat with 4-Passenger Seat:
Using moulding remover A, detach the 7 claws and 3 guides.
for 2-leg Type:
Using moulding remover A, detach the 7 claws and 2 guides.
w/ Reclining Function:
Pull out the seat reclining handle belt from the hole in the reclining adjuster cover RH.
Remove the reclining adjuster cover RH.
71812C
3.REMOVE RECLINING ADJUSTER COVER LH
w/ Seatback Board:
Remove the screw.
w/o Seatback Board:
Remove the 2 screws.
| *A | w/o Seatback Board |
for 1-leg Type, 7th Row Seat with 4-Passenger Seat:
Using moulding remover A, detach the 7 claws and 3 guides.
for 2-leg Type:
Using moulding remover A, detach the 7 claws and 2 guides.
w/ Reclining Function:
Pull out the seat reclining handle belt from the hole in the reclining adjuster cover LH.
Remove the reclining adjuster cover LH.
72379
4.REMOVE SEAT RECLINING HANDLE BELT (w/ Reclining Function)
Use the same procedure for the other seat reclining handle belts.
Remove the seat reclining handle belt from the No. 1 seatback spring assembly RH.
71148N
5.REMOVE REAR SEAT OUTER LEG COVER
for 1st Row Seat with Step:
Remove the 4 screws.
Using a clip remover with its tip wrapped with protective tape, detach the 4 clips.
|
Protective Tape |
Using moulding remover A, detach the 10 claws and remove the rear seat outer leg cover.
except 1st Row Seat with Step:
Remove the 3 screws.
Using a clip remover with its tip wrapped with protective tape, detach the 4 clips.
|
Protective Tape |
Using moulding remover A, detach the 9 claws and 2 guides and remove the rear seat outer leg cover.
71149K
6.REMOVE REAR SEAT INNER LEG COVER
for 1st Row Seat with Step:
Remove the screw.
Detach the claw and 2 guides and remove the rear seat inner leg cover.
except 1st Row Seat with Step:
Remove the screw.
Detach the 2 claws and 2 guides and remove the rear seat inner leg cover.
| *A | except 1st Row Seat with Step | *B | for Standard Body 1-leg Type 5th Row Seat without Sub Seat |
79967J
7.REMOVE REAR NO. 4 SEAT LEG SIDE COVER (for 7th Row Seat with 4-Passenger Seat)
Detach the 3 pieces of fastening tape.
|
Fastening Tape |
Detach the hook and fastening tape and remove the rear No. 4 seat leg side cover.
|
Fastening Tape |
71149R
8.REMOVE REAR SEAT INNER LEG COVER (for 2-leg Type)
Remove the 3 screws.
Detach the 3 clips.
Using moulding remover A, detach the 9 claws and 2 guides and remove the rear seat inner leg cover.
71148C
9.REMOVE REAR SEAT OUTER LEG COVER (for 2-leg Type)
Remove the screw.
Detach the 2 claws and 2 guides and remove the rear seat inner leg cover.
74617C
10.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)
Use the same procedure for the other assist grip plugs.
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the 2 claws and remove the assist grip plug.
|
Protective Tape |
74610A
11.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
Use the same procedure for the other assist grip sub-assemblies.
Remove the 2 screws and assist grip sub-assembly.
79209
12.REMOVE NO. 2 SEATBACK BOARD SUB-ASSEMBLY (w/ Seatback Board)
Use the same procedure for the other No. 2 seatback board sub-assemblies.
Slide the No. 2 seatback board sub-assembly in the direction indicated by the arrow shown in the illustration and detach the 3 guides to remove it.
73178A
13.REMOVE SEAT BELT ANCHOR COVER CAP
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the 2 claws and 3 guides and remove the seat belt anchor cover cap.
|
Protective Tape |
73179A
14.REMOVE SEAT BELT ANCHOR COVER CAP LH
Use the same procedure as for the seat belt anchor cover cap.
73373A
15.REMOVE REAR SEAT SHOULDER BELT COVER RH
Using moulding remover A, detach the 2 claws.
Slide the part in the direction indicated by the arrow shown in the illustration and detach the 2 guides.
Remove the rear seat outer belt assembly from the gap in the rear seat shoulder belt cover RH to remove the rear seat shoulder belt cover RH.
| *a | Gap |
73375
16.REMOVE REAR SEAT SHOULDER BELT COVER LH
Use the same procedure described for the RH side.
17.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
18.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR
Use the same procedure as for the rear seat outer belt assembly floor anchor.
73375M
19.REMOVE REAR SEAT SHOULDER BELT HOLE COVER (w/o Seatback Board)
Use the same procedure for the other rear seat shoulder belt hole covers.
Remove the 3 hog rings.
Pull out the fastener.
Open the fastener.
Detach the 10 claws and 8 guides and remove the rear seat shoulder belt hole cover.
73135A
20.REMOVE SHOULDER BELT ANCHOR COVER RH
Remove the 2 screws and pull out the shoulder belt anchor cover RH.
Remove the rear seat outer belt assembly from the gap in the shoulder belt anchor cover RH to remove the shoulder belt anchor cover RH.
| *a | Gap |
73136A
21.REMOVE SHOULDER BELT ANCHOR COVER LH
Use the same procedure as for the shoulder belt anchor cover RH.
73373D
22.REMOVE REAR SEAT SHOULDER BELT HOLE COVER RH
Slide the part in the direction indicated by the arrow shown in the illustration and detach the claw and guide.
Slide the part in the direction indicated by the arrow shown in the illustration and detach the 2 clamps.
Remove the rear seat outer belt assembly from the gap in the rear seat shoulder belt hole cover RH to remove the rear seat shoulder belt hole cover RH.
| *a | Gap |
73375B
23.REMOVE REAR SEAT SHOULDER BELT HOLE COVER LH
Use the same procedure described for the RH side.
73360B
24.REMOVE REAR SEAT OUTER BELT ASSEMBLY
73350C
25.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY
Use the same procedure as for the rear seat outer belt assembly.
26.REMOVE REAR SEAT SHOULDER BELT COVER RH
Using a needle-nose pliers with the tips wrapped with protective tape, detach the 2 claws A and remove the clip.
| *a | Claw A |
| *b | Claw B |
Detach the claw B and guide and remove the rear seat shoulder belt cover RH.
27.REMOVE REAR SEAT SHOULDER BELT COVER LH
Use the same procedure described for the RH side.
79013
28.REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY RH
w/ Seatback Board:
Remove the 3 hog rings.
Remove the 2 hog rings.
Remove the 2 hog rings and No. 1 seatback cover sub-assembly RH.
79014
29.REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY LH
Use the same procedure described for the RH side.
79017A
30.REMOVE NO. 1 SEATBACK PAD SUB-ASSEMBLY RH
Remove the No. 1 seatback pad sub-assembly RH.
79018A
31.REMOVE NO. 1 SEATBACK PAD SUB-ASSEMBLY LH
Use the same procedure described for the RH side.
73343
32.REMOVE REAR SEAT SHOULDER BELT GUIDE RH
Use the same procedure for the other rear seat shoulder belt guides RH.
Remove the 2 screws.
Detach the guide and remove the rear seat shoulder belt guide RH.
79021
33.REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH
Detach the fastening tape and fold back the No. 2 seat cushion cover sub-assembly RH.
|
Fastening Tape |
Detach the 9 hooks.
for 2-leg Type 5th Row Seat:
Pull out the strap of the No. 2 seat cushion cover sub-assembly RH from the No. 1 seat leg sub-assembly RH.
Remove the No. 2 seat cushion cover sub-assembly RH with pad from the No. 1 seat leg sub-assembly RH.
for 1-leg Type:
Detach the 6 pieces of fastening tape.
|
Fastening Tape |
for 2-leg Type:
Detach the 2 pieces of fastening tape.
|
Fastening Tape |
Remove the 12 hog rings and No. 2 seat cushion cover sub-assembly RH from the No. 2 seat cushion pad RH.
71867N
34.REMOVE REAR NO. 1 SEAT INNER CUSHION SHIELD RH
Remove the screw and rear No. 1 seat inner cushion shield RH.
71868C
35.REMOVE REAR NO. 1 SEAT INNER CUSHION SHIELD LH
w/ Seatback Board:
Remove the 2 screws and rear No. 1 seat inner cushion shield LH.
| *A | w/ Seatback Board |
w/o Seatback Board:
Remove the screw and rear No. 1 seat inner cushion shield LH.
71874M
36.REMOVE REAR SEAT LOWER CUSHION SHIELD LH
Remove the screw.
Using moulding remover A, detach the 6 claws and remove the rear seat lower cushion shield LH.
71873D
37.REMOVE REAR SEAT LOWER CUSHION SHIELD RH
Remove the screw and rear seat lower cushion shield RH.
72345A
38.REMOVE RECLINING CONNECTING PIPE
Remove the reclining connecting pipe.
72995A
39.REMOVE REAR SEAT COVER
Detach the fastening tape.
|
Fastening Tape |
Remove the rear seat cover.
73380F
40.REMOVE REAR SEAT INNER BELT ASSEMBLY
Use the same procedure as for the other rear seat inner belt assemblies.
Remove the bolt and rear seat inner belt assembly.
71875F
41.REMOVE SEAT RECLINING ADJUSTER INSIDE COVER RH (w/ Reclining Function)
Using a clip remover, remove the clip.
Detach the 4 guides and remove the reclining adjuster inside cover RH.
71875G
42.REMOVE SEAT RECLINING ADJUSTER INSIDE COVER LH (w/ Reclining Function)
Use the same procedure described for the RH side.
79180A
43.REMOVE NO. 1 SEATBACK SPRING ASSEMBLY RH
Remove the 2 bolts.
Detach the 2 guides and remove the No. 1 seatback spring assembly RH.
79190A
44.REMOVE NO. 1 SEATBACK SPRING ASSEMBLY LH
Use the same procedure described for the RH side.