Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356198 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



a.

Visually check for defects with the spiral cable sub-assembly.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector


OK:

No defects are found.


If any of the defects mentioned below are found, replace the spiral cable sub-assembly with a new one:



b.
B284475E02
0.219,0.781 0.5,0.979 0.281,0.198 2.74,4.083 3.021,4.281 0.281,0.198 2.458,1.135 2.74,1.333 0.281,0.198 1.375,0.938 1.656,1.135 0.281,0.198 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.313,0.802 0.49,1.01 0.177,0.208 10 false A 2.833,4.104 3.01,4.302 0.177,0.198 10 false B 1.469,0.958 1.656,1.167 0.188,0.208 10 false C 2.552,1.156 2.74,1.354 0.188,0.198 10 false D

Check the spiral cable sub-assembly.

Text in Illustration
*a Component without harness connected
(spiral cable sub-assembly)

i.

Set the spiral cable sub-assembly to the center position (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - C-2 Always 0.4 to 1.25 Ω
A-2 - C-1 Always 0.4 to 1.25 Ω
B-2 -D-8 Always 0.33 to 1.09 Ω
B-3 - D-1 Always 0.33 to 1.09 Ω
B-4 - D-2 Always 0.33 to 1.09 Ω



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly clockwise 4 times and measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - C-2 Always 0.4 to 1.25 Ω
A-2 - C-1 Always 0.4 to 1.25 Ω
B-2 -D-8 Always 0.33 to 1.09 Ω
B-3 - D-1 Always 0.33 to 1.09 Ω
B-4 - D-2 Always 0.33 to 1.09 Ω


If the results are not as specified, replace the spiral cable sub-assembly.


iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly clockwise 4 times. Then, while rotating the spiral cable sub-assembly counterclockwise 8 times and measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - C-2 Always 0.4 to 1.25 Ω
A-2 - C-1 Always 0.4 to 1.25 Ω
B-2 -D-8 Always 0.33 to 1.09 Ω
B-3 - D-1 Always 0.33 to 1.09 Ω
B-4 - D-2 Always 0.33 to 1.09 Ω


If the results are not as specified, replace the spiral cable sub-assembly.

NOTICE:

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.