Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356198 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

w/ Steering Sensor:

If the steering sensor is installed to a misaligned spiral cable, DTCs for an abnormal steering sensor value such as DTC C1433 is stored and it is impossible to repair them. If this happens, replace the spiral cable sub-assembly with a new one.


a.
B464679E01
1.948,0.896 2.323,1.271 0.375,0.375 2.385,2.083 2.781,2.083 true 2.313,2.156 2.313,2.635 2.313,2.635 2.802,2.635 true 2.823,2.021 3.135,2.219 0.313,0.198 10 false *a 2.854,2.552 3.167,2.75 0.313,0.198 10 false *c 1.979,0.917 2.188,1.083 0.208,0.167 10 true *b

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


Text in Illustration
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


b.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.


·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.


i.
B464680

Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


Text in Illustration
V100135

Counterclockwise



c.
B464681

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


d.
B464682

Rotate the spiral cable sub-assembly clockwise approximately 4 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


Text in Illustration
V100135

Clockwise


e.
B464679E02
1.958,0.885 2.333,1.271 0.375,0.385 2.375,2.073 2.76,2.073 true 2.292,2.156 2.292,2.625 2.292,2.625 2.75,2.625 true 2,0.917 2.208,1.104 0.208,0.188 10 true *b 2.802,2 3.115,2.198 0.313,0.198 10 false *a 2.813,2.552 3.125,2.75 0.313,0.198 10 false *c

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


Text in Illustration
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn

NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 2.INSTALL SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
w/ Steering Sensor:
·

Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch on (IG).

·

Do not rotate the spiral cable sub-assembly with the battery connected and the ignition switch on (IG).

·

When rotating the spiral cable sub-assembly to check the operation of the spiral cable subassembly (checking for abnormal noise, checking the DTC, Data list, etc) make sure to perform the inspection with the steering wheel assembly installed.

·

If the steering sensor is installed to a misaligned spiral cable, DTCs for an abnormal steering sensor value such as DTC C1433 is stored and it is impossible to repair them. If this happens, replace the spiral cable sub-assembly with a new one.

·
B284476

When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

Text in Illustration
V100135

Lock Pin



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the front wheels are facing straight ahead.


d.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch cancel ratchet may snap.



e.

Attach the 3 claws and install the spiral cable sub-assembly.


f.
B468093E01
0.531,2.26 0.74,2.406 true 1.99,2.229 2.635,2.469 true 0.385,2.167 0.625,2.344 0.24,0.177 10 false *a 1.833,2.177 2.073,2.354 0.24,0.177 10 false *b

Connect the connectors to the spiral cable sub-assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.


Text in Illustration
*a Slider
*b Lock Position


g.

Check that the lock slider is in the lock position.


Hide 45286B 3.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 4.INSTALL LOWER STEERING COLUMN COVER

Hide 84306 5.ADJUST SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B464683E02
1.698,0.875 2.115,1.177 0.417,0.302 2.885,2.573 2.885,1.917 2.885,1.917 3.135,1.917 true 2.354,3.177 2.813,3.177 2.813,3.177 2.813,2.635 true 3.167,1.813 3.385,2.01 0.219,0.198 10 false *a 2.198,3.094 2.51,3.292 0.313,0.198 10 false *c 1.75,0.896 1.927,1.063 0.177,0.167 10 true *b

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


Text in Illustration
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


d.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B464684

Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


Text in Illustration
V100135

Counterclockwise



e.
B464685

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


f.
B464686

Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

Text in Illustration
V100135

Clockwise

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.



g.
B464683E03
1.698,0.865 2.125,1.177 0.427,0.313 2.813,2.635 2.813,3.198 2.813,3.198 2.427,3.198 true 3.188,2 2.917,2 2.917,2 2.917,2.573 true 3.198,1.917 3.417,2.125 0.219,0.208 10 false *a 2.229,3.115 2.448,3.323 0.219,0.208 10 false *c 1.74,0.875 1.917,1.042 0.177,0.167 10 true *b

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


Text in Illustration
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn

NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

a.

Check that the front wheels are facing straight ahead.


Hide 7.INSTALL STEERING WHEEL ASSEMBLY

Hide 8.INSPECT STEERING WHEEL CENTER POINT

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION