68217A
1.INSTALL NO. 1 SIDE WINDOW PIN
Using non-residue solvent, clean the No. 1 side window pin installation surface of the center door glass.
Install the glass primer to the No. 1 side window pin installation surface of the center door glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new No. 1 side window pin.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 6 No. 1 side window pins to the center door glass as shown in the illustration.
| *A | Rear Side | *B | Front Side |
| *a | Back Side | *b | Ceramic Notch |
62267V
2.INSTALL SIDE WINDOW ADHESIVE DAM
Use the same procedure for each of the center door glass.
Using non-residue solvent, clean the side window adhesive dam installation surface of the center door glass.
Install the glass primer to the side window adhesive dam installation surface of the center door glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new side window adhesive dam.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 4 side window adhesive dams to the center door glass as shown in the illustration.
| *a | Back Side | *b | Ceramic Notch |
68111
3.INSTALL CENTER DOOR GLASS
Use the same procedure for each of the center door glass.
Clean and shape the contact surface of the door panel.
On the contact surface of the door panel, use a knife to cut away excess adhesive as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.) |
Clean the contact surface of the door panel with non-residue solvent.
| *a | Door Panel |
|
Adhesive |
Position the center door glass.
Using suction cups, place the center door glass in the correct position.
Check that the entire contact surface of the glass rim is perfectly even.
Using suction cups, remove the center door glass.
Using a brush or sponge, apply body primer to the exposed part of the door panel.
Do not apply too much primer.
Do not apply primer to the adhesive.
When applying the primer, take care of the seams of the panel and spot welds.
Using a brush or sponge, apply glass primer to the contact surface of the glass.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Adhesive Center |
|
Glass Primer Application Area | - | - |
| Area | Specified Condition |
|---|---|
| a | 20.0 mm (0.787 in.) |
| b | 28.0 mm (1.10 in.) |
Apply adhesive to the center door glass.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *1 | Sealer Gun |
After cutting off the tip, use all adhesive within the time written in the table below.
Load the sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Adhesive Center |
|
Adhesive | - | - |
| Area | Specified Condition |
|---|---|
| a | 13.0 mm (0.512 in.) |
| b | 8.0 mm (0.315 in.) |
Install the center door glass to the door panel.
Using suction cups, attach the 3 No. 1 side window pins and install the center door glass.
| *A | Front Side |
| *B | Rear Side |
Press it in gently along the rim.
Check that the stoppers are attached to the door panel correctly.
Check that the door panel and glass have a small gap between them.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
4.INSPECT FOR LEAKS AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
74642
5.INSTALL FOLDING DOOR ASSIST GRIP
68218D
6.INSTALL CENTER DOOR FIX WINDOW BUSH
69278
7.INSTALL NO. 1 DOOR INSIDE HANDLE BEZEL LH
69298F
8.INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH