Home › Engine / Hybrid System › 1BZ-FPE (STARTING) › STARTER › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073205 1BZ-FPE STARTING _0356278 STARTER G

1BZ-FPE STARTING  STARTER  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

These tests must be done within 3 to 5 seconds to avoid burning out the coil.


PROCEDURE

Hide 1. DO PULL-IN TEST

a.
A423904

Disconnect the field coil lead wire from terminal C.


b.

Connect the battery to the magnetic switch as shown.

Check that the clutch pinion gear moves outward.


Hide 2. DO HOLD-IN TEST

a.
A423905

With battery connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.


Hide 3.INSPECT CLUTCH PINION GEAR RETURN

a.
A423906

Disconnect the negative (-) lead from the switch body.


b.

Check that the clutch pinion gear returns inward.


Hide 4. DO NO-LOAD PERFORMANCE TEST

a.
A423907

Connect the battery and ammeter to the starter as shown.


b.

Check that the starter rotates smoothly and steadily with the pinion gear moving out. Check that the ammeter shows the specified current.

Specified current:

180 A or less at 11.0 V



Hide 5.INSPECT ARMATURE COIL

a.
A423879

Check the commutator for open circuit.

Using an ohmmeter, check that there is continuity between the segments of the commutator.

If there is no continuity between any segment, replace the armature.


b.
A423880

Check the commutator for ground.

Using an ohmmeter, check that there is no continuity between the commutator and armature coil core.

If there is continuity, replace the armature.


Hide 6.INSPECT COMMUTATOR

a.

Check the commutator for the dirty and burnt surfaces.

If the surface is dirty or burnt, correct it with sandpaper (No.400) or on a lathe.


b.
A423881

Check for the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial gauge, measure the circle runout.

Maximum circle runout:

0.05 mm (0.0020 in.)


If the circle runout is greater than maximum, correct it on a lathe.



c.
A423882

Using vernier calipers, measure the commutator diameter.

Standard diameter:

36.0 mm (1.417 in.)


Minimum diameter:

35.0 mm (1.378 in.)


If the diameter is less than minimum, replace the armature.


d.
A423883

Check that the undercut depth is clean and free of foreign materials. Smooth out the edge.

Standard undercut depth:

0.7 mm (0.028 in.)


Minimum undercut depth:

0.2 mm (0.008 in.)


If the undercut depth is less than minimum, correct it with a hacksaw blade.


Hide 7.INSPECT FIELD COIL

a.
A423884

Check the field coil for open circuit.

Using an ohmmeter, check that there is continuity between the lead wire and field coil brush lead.

If there is no continuity, replace the field frame.


b.
A423885

Check the field coil for ground.

Using an ohmmeter, check that there is no continuity between the field coil end and field frame.

If there is continuity, repair or replace the field frame.


Hide 8.INSPECT BRUSHES

a.
A423886

Using vernier calipers, measure the brush length.

Standard length:

20.5 mm (0.807 in.)


Minimum length:

11.0 mm (0.433 in.)


If the length is less than minimum, replace the brush holder and field frame.


Hide 9.INSPECT BRUSH SPRING

a.
A423887

Check the brush spring load.

Take the pull scale reading the instant the brush spring separates from the brush.

Standard spring installed load:

34.3 - 42.1 N (3.5 - 4.3 kgf, 7.7 - 9.5 lbf)


Minimum spring installed load:

18.6 N (1.9 kgf, 4.2 lbf)


If the installed load is less than minimum replace the brush springs.


Hide 10.INSPECT BRUSH HOLDER

a.
A423888

Check the brush holder insulation.

Using an ohmmeter, check that there is no continuity between the positive (+) and negative (-) brush holders.

If there is continuity, repair or replace the brush holder.


Hide 11.INSPECT CLUTCH AND GEAR

a.

Check the gear teeth on the pinion gear, idler gear and clutch assembly for wear or damage.

If damaged, replace the gear or clutch assembly.

If damaged, also check the ring gear of the flywheel/drive plate for wear or damage.


b.
A423889

Check the clutch pinion gear.

Hold the starter clutch and rotate the pinion gear counterclockwise, and check that it turns freely. Try to rotate the pinion gear clockwise and check that it locks.

If necessary, replace the clutch assembly.


Hide 12.INSPECT MAGNETIC SWITCH

a.
A423890

Check the pull-in coil for open circuit.

Using an ohmmeter, check that there is continuity between terminals 50 and C.

If there is no continuity, check and replace the magnetic switch.


b.
A423891

Check the hold-in coil for open circuit.

Using an ohmmeter, check that there is continuity between terminal 50 and the switch body.

If there is no continuity, replace the magnetic switch.


Hide 13.INSPECT BEARING

a.

Turn the bearing by hand while applying inward force.

If resistance is felt or the bearing sticks, replace the bearing

Click hereEngine / Hybrid System>1BZ-FPE (STARTING)>STARTER>REPLACEMENT