Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR (for N04C-UH)
RM2850E _58 Vehicle Interior _073207 AIR CONDITIONING _0356304 COMPRESSOR(for N04C-UH) A

AIR CONDITIONING  COMPRESSOR(for N04C-UH)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
I103302E04
0.448,0.469 0.76,0.667 0.313,0.198 10 false *1 1.948,0.469 2.26,0.667 0.313,0.198 10 false *2 0.729,3.958 1.042,4.156 0.313,0.198 10 false *3 0.708,3.427 1.021,3.625 0.313,0.198 10 false *4 2.229,3.417 2.542,3.615 0.313,0.198 10 false *5

When replacing the compressor with a new one, gradually discharge the refrigerant gas from the service valve. Then drain the following amount of oil from the new compressor before installation, so that the amount of oil contained in it is the same as that in the compressor to be replaced.

Text in Illustration
*1 New Compressor and Magnet Clutch
*2 Removed Compressor and Magnet Clutch
*3 Drain Extra Oil (A - B)
*4 A
*5 B

HINT:

New compressors are filled with sufficient oil for the whole cycle. Therefore, it is necessary to drain excess oil from the condenser and cooling unit.


Standard:

(The amount of oil inside a new compressor: 400 (+/- 30) cc (13.5 (+/- 1.01) fl.oz.)) - (The amount of oil in the removed compressor) = The amount of oil to be removed from the new compressor


NOTICE:
·

When checking the compressor oil level, observe the precautions for cooler removal/ installation.

·

If a new compressor is installed without removing the excess oil, the amount of oil in the system becomes too large. This prevents heat exchange in the refrigerant cycle and causes refrigeration failure.

·

If the amount of oil in the removed compressor is too small, check for oil leakage.

·

Use ND-OIL8 compressor oil.




Hide 88720A 2.CONNECT AIR CONDITIONING HOSE AND ACCESSORY

a.

Remove the attached vinyl tape from the suction hose.


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the suction hose.


d.

Connect the suction hose to the compressor with the bolt.

Torque:

9.8 N*m (100 kgf*cm, 87 in.*lbf)



e.

Remove the attached vinyl tape from the discharge hose.


f.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL8 or equivalent



g.

Install the O-ring onto the discharge hose.


h.

Connect the discharge hose to the compressor with the bolt.

Torque:

9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 3.INSTALL COMPRESSOR AND MAGNETIC CLUTCH

a.

Install the compressor together with hose with the 4 bolts.

Torque:

47 N*m (475 kgf*cm, 34 ft.*lbf)


NOTICE:

Do not apply excessive force to the air conditioning hose.



b.

Connect the connector.


c.

Install the air conditioning hoses with the 2 bolts.

Torque:

47 N*m (475 kgf*cm, 34 ft.*lbf)



Hide 88310A 4.INSTALL NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT

a.

Install the No. 1 V (cooler compressor to crankshaft pulley) belt.

Click hereEngine / Hybrid System>N04C-UH (ENGINE MECHANICAL)>DRIVE BELT>INSTALLATION


Hide 5. CHARGE REFRIGERANT

Standard:

2000 +/- 50 g (70.55 +/- 1.76 OZ.) for LHD

1950 +/- 50 g (68.78 +/- 1.76 OZ.) for RHD


Hide 7.INSPECT FOR REFRIGERANT LEAK

Using a halogen leak detector, check for leakage of refrigerant.

If there is leakage, check the tightening torque at the joints.