Home › Vehicle Interior › EXTERIOR › FRONT DOOR BLACK OUT TAPE
RM2850E _58 Vehicle Interior _073214 EXTERIOR _0356381 FRONT DOOR BLACK OUT TAPE A

EXTERIOR  FRONT DOOR BLACK OUT TAPE  INSTALLATION  


PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

using a heat light, heat the vehicle body surface.

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




ii.

wipe off any tape adhesive with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light.

When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf. 1.45 to 6.71 lbf.) while moving the squeegee at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.

B233855E19
0.083,0.073 3.875,1.563 3.792,1.49 0.688,0.625 0.833,0.479 0.833,0.479 1,0.479 false 2.177,0.74 2.292,0.365 2.292,0.365 2.542,0.365 false 2.135,1.25 2.833,1.25 false 2.146,1.99 2.146,1.823 2.146,1.823 2.604,1.823 true 2.094,3.427 2.646,3.427 true 4.594,2.635 4.99,2.635 false 4.875,3.052 5.302,3.052 false 5.698,2.635 5.938,2.979 5.938,2.979 6.052,2.979 true 5.677,3.271 6.073,3.271 false 1.021,2.865 1.781,2.865 1.781,2.865 2.021,2.281 false 1.125,3.26 1.646,3.26 false 4.552,2.24 5,2.5 0.448,0.26 10 false *e 2.698,1.729 3.292,1.969 0.594,0.24 10 false *d 6.125,2.885 6.583,3.198 0.458,0.313 10 false *g 2.885,2.385 3.281,2.698 0.396,0.313 10 false *f 0.167,0.104 0.427,0.385 0.26,0.281 10 false *a 2.594,0.281 2.875,0.542 0.281,0.26 10 false *b 2.885,1.167 3.198,1.448 0.313,0.281 10 false *c 1.021,0.396 1.323,0.667 0.302,0.271 10 false *1 0.813,2.792 1.146,3.052 0.333,0.26 10 false *1 0.094,1.635 0.5,1.906 0.406,0.271 10 false *A 0.938,3.177 1.229,3.406 0.292,0.229 10 false *2 4.406,2.542 4.708,2.802 0.302,0.26 10 false *1 4.667,2.979 5.063,3.25 0.396,0.271 10 false *2 2.688,3.344 2.958,3.573 0.271,0.229 10 false *3 3.677,1.635 4,1.885 0.323,0.25 10 false *B 6.115,3.198 6.51,3.469 0.396,0.271 10 false *3 1.083,2.25 1.531,2.51 0.448,0.26 10 false *e 6.354,2.042 6.75,2.354 0.396,0.313 10 false *f

Text in Illustration
*A Protective Tape *B Pulling
*1 Squeegee *2 Black Out Tape
*3 Release Paper - -
*a Sectional View *b Non-padded Side
*c Padded Side *d 40 to 50° (for pressing forward)
*e 30 to 70 mm/sec. (1.18 to 2.76 in/sec.) *f 10 to 20 mm (0.39 to 0.79 in.)
*g 30 to 45° (for pulling) - -

NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.39 to 0.79 in.) from the edge of the squeegee.





f.
B233856E04
0.969,1.792 1.083,1.792 1.083,1.792 1.198,1.698 false 0.74,1.698 0.938,1.854 0.198,0.156 10 false *1 2.333,0.438 2.51,0.615 0.177,0.177 10 false *a 1.625,0.333 1.823,0.51 0.198,0.177 10 false *b 0.906,0.427 1.115,0.625 0.208,0.198 10 false *c 1.771,1.833 2.104,2.031 0.333,0.198 10 false *2

Key points for the installation of the tape (how to use a squeegee and the installation procedure for a hemming surface).

i.

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

Text in Illustration
*1 Squeegee
*2 Hem
*a First
*a Second
*b Third

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.



h.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75923B 2.INSTALL NO. 2 BLACK OUT TAPE RH

HINT:

When installing the No. 2 black out tape RH, heat the front door panel and No. 2 black out tape RH using a heat light.


Standard
Item Temperature
Front Door Panel 40 to 60°C( 104 to 140°F)
No. 2 Black Out Tape RH 20 to 30°C( 68 to 86°F)

NOTICE:
·

Do not heat the front door panel or No. 2 black out tape RH excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Refer to the illustration to position a new No. 2 black out tape RH.

B466103E01
5.958,1.688 6.313,1.125 6.313,1.125 6.49,1.125 true 6.563,1.573 6.583,1.219 true 1.229,0.823 1.542,0.823 false 1.604,0.74 1.979,1.042 0.375,0.302 10 false *c 6.531,1.031 6.865,1.26 0.333,0.229 10 false *d 5.76,1.156 6.104,1.438 0.344,0.281 10 false *a 6.854,1.5 7.146,1.74 0.292,0.24 10 false *b 3.865,1.073 4.021,1.26 0.156,0.188 10 false A 4.188,1.01 4.344,1.198 0.156,0.188 10 false A

Text in Illustration
*a 3.0 mm (0.118 in.) (Reference value) *b 2.0 mm (0.079in.)
*c Peeling Paper Slit *d Edge of Curved Surface


b.

Remove the release paper and application tape from the No. 2 black out tape RH.


Hide 75957C 3.INSTALL FRONT DOOR OUTER REAR BLACK OUT TAPE RH

HINT:

When installing the front door outer rear black out tape RH, heat the front door panel and front door outer rear black out tape RH using a heat light.


Standard
Item Temperature
Front Door Panel 40 to 60°C( 104 to 140°F)
Front Door Outer Rear Black Out Tape RH 20 to 30°C( 68 to 86°F)

NOTICE:
·

Do not heat the front door panel or front door outer rear black out tape RH excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Refer to the illustration to position a new front door outer rear black out tape RH.

B466104E01
1.208,0.646 1.469,0.646 false 4.479,1.615 4.479,1.208 4.479,1.208 4.594,1.208 false 6.115,1.74 5.854,1.698 5.854,1.698 5.854,1.552 false 1.51,0.563 1.823,0.76 0.313,0.198 10 false *c 2.156,1.052 2.417,1.281 0.26,0.229 10 false A 2.458,1.042 2.708,1.281 0.25,0.24 10 false A 5.406,0.531 5.854,0.802 0.448,0.271 10 false A-A 6.146,1.177 6.354,1.375 0.208,0.198 10 false *a 5.75,1.365 5.958,1.563 0.208,0.198 10 false *d 4.625,1.135 4.833,1.333 0.208,0.198 10 false *d 4.083,1.563 4.292,1.76 0.208,0.198 10 false *b

Text in Illustration
*a 8.0 mm (0.315 in.) *b 3.0 mm (0.118 in.)
*c Peeling Paper Slit *d Edge of Curved Surface


b.

Remove the release paper and application tape from the front door outer rear black out tape RH.


Hide 75925B 4.INSTALL NO. 3 BLACK OUT TAPE RH

HINT:

When installing the No. 3 black out tape RH, heat the front door panel and No. 3 black out tape RH using a heat light.


Standard
Item Temperature
Front Door Panel 40 to 60°C( 104 to 140°F)
No. 3 Black Out Tape RH 20 to 30°C( 68 to 86°F)

NOTICE:
·

Do not heat the front door panel or No. 3 black out tape RH excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Refer to the illustration to position a new No. 3 black out tape RH.

B466105E01
1.719,1.656 1.719,1.031 1.719,1.031 1.917,1.031 true 5.573,1.719 5.115,1.719 5.115,1.719 5.115,1.333 true 4.552,2.219 4.698,2.219 4.698,2.219 4.698,2.604 false 6.74,2.354 6.938,2.354 6.938,2.354 6.938,2.76 false 6.188,3.479 6.083,3.479 6.083,3.479 6.083,3.198 true 1.969,0.969 2.281,1.167 0.313,0.198 10 false *d 2.677,1.625 2.99,1.823 0.313,0.198 10 false A 2.667,2.125 2.979,2.323 0.313,0.198 10 false A 3.302,2.198 3.469,2.396 0.167,0.198 10 true B 3.823,2.208 3.99,2.406 0.167,0.198 10 true B 5.281,0.177 5.594,0.375 0.313,0.198 10 false A-A 5.51,2.135 5.823,2.333 0.313,0.198 10 false B-B 4.292,2.542 4.521,2.74 0.229,0.198 10 false *b 6.24,3.125 6.49,3.344 0.25,0.219 10 false *b 5.5,1.125 5.771,1.375 0.271,0.25 10 false *c 5.635,1.635 5.927,1.896 0.292,0.26 10 false *e 4.375,2.115 4.604,2.313 0.229,0.198 10 false *e 6.563,2.26 6.823,2.479 0.26,0.219 10 false *e 6.458,2.688 6.75,2.927 0.292,0.24 10 false *a 6.24,3.417 6.542,3.646 0.302,0.229 10 false *e

Text in Illustration
*a 3.0 mm (0.118 in.) *b 4.0 mm (0.157 in.) (Reference value)
*c 10.0 mm (0.394 in.) (Reference value) *d Peeling Paper Slit
*g Edge of Curved Surface - -


b.

Remove the release paper and application tape from the No. 3 black out tape RH.


Hide 75921C 5.INSTALL NO. 1 BLACK OUT TAPE RH

HINT:

When installing the No. 1 black out tape RH, heat the front door panel and No. 1 black out tape RH using a heat light.


Standard
Item Temperature
Front Door Panel 40 to 60°C( 104 to 140°F)
No. 1 Black Out Tape RH 20 to 30°C( 68 to 86°F)

NOTICE:
·

Do not heat the front door panel or No. 1 black out tape RH excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Refer to the illustration to position a new No. 1 black out tape RH.

B466101E02
6.583,0.854 6.969,0.854 6.969,0.854 6.969,1.052 false 5.344,2.26 5.583,2.438 0.24,0.177 10 false *a 3.49,0.083 3.646,0.281 0.156,0.198 10 false A 3.5,0.375 3.656,0.573 0.156,0.198 10 false A 6.208,0.281 6.635,0.531 0.427,0.25 10 false A-A 6.396,1.063 6.635,1.24 0.24,0.177 10 false *a 6.906,1.115 7.146,1.292 0.24,0.177 10 false *b

Text in Illustration
*a 3.0 mm (0.118 in.) *b Edge of Curved Surface


b.

Remove the release paper from the No. 1 black out tape RH.


Hide 75955B 6.INSTALL FRONT DOOR OUTER UPPER BLACK OUT TAPE RH

HINT:

When installing the front door outer upper black out tape RH heat the front door panel and front door outer upper black out tape RH using a heat light


Standard
Item Temperature
Front Door Panel 40 to 60°C( 104 to 140°F)
Front Door Outer Upper Black Out Tape RH 20 to 30°C( 68 to 86°F)

NOTICE:
·

Do not heat the front door panel or front door outer upper black out tape RH excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Refer to the illustration to position a new front door outer upper black out tape RH.

B466102E01
1.76,1.156 2.031,1.156 true 6.5,1.042 6.5,0.594 6.5,0.594 6.604,0.594 true 2.063,1.094 2.281,1.292 0.219,0.198 10 false *d 4.979,1.729 5.292,2.052 0.313,0.323 10 false *c 4.333,2.01 4.552,2.208 0.219,0.198 10 false *a 6.542,1.323 6.823,1.552 0.281,0.229 10 false *a 6.635,0.49 6.854,0.688 0.219,0.198 10 false *e 2.719,0.313 2.823,0.458 0.104,0.146 10 true A 2.719,0.094 2.885,0.292 0.167,0.198 10 false A 2.719,0.469 2.823,0.615 0.104,0.146 10 true B 2.729,0.698 2.844,0.865 0.115,0.167 10 false B 4.833,0.156 5.26,0.365 0.427,0.208 10 false A-A 6.073,0.177 6.458,0.385 0.385,0.208 10 false B-B

Text in Illustration
*a 0.6 mm (0.024 in.) (Reference value) *b 5.0 mm (0.197 in.)
*c Over Lap *d Peeling Paper Slit
*e Edge of Curved Surface - -


b.

Remove the release paper and application tape from the front door outer upper black out tape RH.


c.

Apply the front door upper outer black out tape RH so that it overlaps with the No. 1 black out tape as shown in the illustration.


Hide 7.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY RH