Home › Vehicle Interior › EXTERIOR › SIDE STRIPE TAPE (for Glide Type)
RM2850E _58 Vehicle Interior _073214 EXTERIOR _0356382 SIDE STRIPE TAPE(for Glide Type) A

EXTERIOR  SIDE STRIPE TAPE(for Glide Type)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light.

When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.



f.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75895L 2.INSTALL NO. 1 MOULDING TAPE

HINT:

When installing the No. 1 moulding tape, heat the vehicle body and No. 1 moulding tape using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
No. 1 Moulding Tape 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or No. 1 moulding tape excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Apply a new No. 1 moulding tape in the position shown in the illustration.

B619490N02
3.469,3.521 3.938,3.417 true 3.604,3.021 4.031,3.021 false 3.417,2.198 3.885,2.396 0.469,0.198 10 false A-A 3.552,1.365 3.708,1.563 0.156,0.198 10 false A 3.563,1.698 3.719,1.896 0.156,0.198 10 false A 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 4.698,2.24 4.802,2.406 0.104,0.167 10 true 1 4.146,2.948 4.458,3.146 0.313,0.198 10 false *b 4,3.302 4.313,3.5 0.313,0.198 10 false *b 3.313,2.656 3.625,2.854 0.313,0.198 10 false *c 2.99,3.375 3.302,3.573 0.313,0.198 10 false *d 5.396,1.563 5.563,1.74 0.167,0.177 10 true 2 5.458,1.99 5.625,2.167 0.167,0.177 10 true 4 5.073,2.365 5.24,2.542 0.167,0.177 10 true 3 2.354,2.281 2.458,2.448 0.104,0.167 10 true 1 1.615,1.531 1.781,1.708 0.167,0.177 10 true 2 2.021,2.406 2.188,2.583 0.167,0.177 10 true 3 1.594,2.021 1.76,2.198 0.167,0.177 10 true 4

Text in Illustration
*a Reference value *b Edge of Curved Surface
*c 3.0 mm (0.118 in.) *d 5.0 mm (0.197 in.)


b.

Fold the corners by hand in the order shown in the illustration.


c.

Using a squeegee, press the corners into place.


Hide 75896M 3.INSTALL NO. 2 MOULDING TAPE

HINT:

When installing the No. 2 moulding tape, heat the vehicle body and No. 2 moulding tape using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
No. 2 Moulding Tape 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or No. 2 moulding tape excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B469698

Apply a new No. 2 moulding tape so that it overlaps the folding part of the No. 1 moulding tape, as shown in the illustration.


Hide 75984A 4.INSTALL SLIDE DOOR STRIPE

HINT:

When installing the slide door stripe, heat the vehicle body and slide door stripe using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Slide Door Stripe 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or slide door stripe excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Apply primer to the positions shown in the illustration.

B620109N01
5.406,2.656 5.656,2.427 true 1.615,2.417 1.865,2.635 true 1.865,2.646 2.177,2.844 0.313,0.198 10 false *a 5.292,2.698 5.604,2.896 0.313,0.198 10 false *a

Text in Illustration
*a Primer - -



c.

Align a new slide door stripe in the horizontal direction in the position shown in the illustration.

B619491N01
5.885,1.052 6.177,1.135 true 5.833,0.813 5.375,1.073 true 1,1.052 1.219,0.802 true 1.24,0.521 1.563,0.604 true 5.875,0.49 6.188,0.688 0.313,0.198 10 false *d 5.25,1.052 5.563,1.25 0.313,0.198 10 false *a 6.24,1.094 6.552,1.292 0.313,0.198 10 false *b 1.667,0.594 1.917,0.771 0.25,0.177 10 true *a 0.896,1.083 1.208,1.281 0.313,0.198 10 false *b 1.052,0.26 1.292,0.438 0.24,0.177 10 false *c

Text in Illustration
*a Slide Door End Face *b Slide Door Stripe End Face
*a 3.0 mm (0.118 in.) *b 3.0 mm (0.118 in.)


d.

Attach the stripe (flat surface).

Click hereVehicle Interior>EXTERIOR>SIDE STRIPE TAPE>INSTALLATION


e.

Attach the stripe (upper edge).

Click hereVehicle Interior>EXTERIOR>SIDE STRIPE TAPE>INSTALLATION


f.

Attach the slide door stripe end slits in the order shown in the illustration.

B619492N01
2.573,4.094 2.573,3.844 true 4.573,4.031 4.573,3.698 true 2.49,4.146 2.75,4.344 0.26,0.198 10 true *b 4.5,4.031 4.76,4.229 0.26,0.198 10 true *b 2.75,3.594 3.01,3.792 0.26,0.198 10 false *a 4.323,3.552 4.583,3.75 0.26,0.198 10 false *a 1.031,1.198 1.188,1.396 0.156,0.198 10 true 3 6.115,3.104 6.271,3.302 0.156,0.198 10 true 1 1.031,3.104 1.188,3.302 0.156,0.198 10 true 1 1.094,1.99 1.25,2.188 0.156,0.198 10 true 2 5.948,2.125 6.104,2.323 0.156,0.198 10 true 2 5.979,1.313 6.135,1.51 0.156,0.198 10 true 3

Text in Illustration
*a 3.0 mm (0.118 in.) *b Edge of Curved Surface


g.

Apply tab tape to the folding part on the slide door stripe in the position shown in the illustration.

B619493