Home › Brake › BRAKE SYSTEM (OTHER) › LOAD SENSING PROPORTIONING VALVE › 2017.01–2019.08
RM2850E _54 Brake _073226 BRAKE SYSTEM (OTHER) _0356442 LOAD SENSING PROPORTIONING VALVE G

BRAKE SYSTEM (OTHER)  LOAD SENSING PROPORTIONING VALVE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1. CHECK REAR WHEEL CYLINDER FLUID PRESSURE

a.

Set the rear axle load.

Standard:
Vehicle Model Rear Axle Load
kN (kgf)
XZB70R-ZEMQY 18.7 (18690)
XZB70R-ZEPQY 18.7 (18690)
XZB70R-ZEMSY 19.5 (19470)
ZXB70R-ZEPSY 19.5 (19470)
HZB70R-ZGMSS 22.1 (22050)
HZB70R-ZGMNS 22.1 (22050)
HZB70L-ZGMRS 22.1 (22050)
HZB70L-ZGMSS 22.1 (22050)
HZB70L-ZXMSS 22.1 (22050)
HZB70L-ZGMTS 22.1 (22050)
HZB70L-ZGMNS 22.1 (22050)
BZB70R-ZCMSC5 19.5 (19470)
XZB70R-ZEMSYQ 19.5 (19470)
XZB70R-ZEPSYQ 19.5 (19470)
XZB70R-ZEPNYQ 19.5 (19470)
HZB70L-ZGMSSV 22.1 (22050)
HZB70L-ZXMSSV 22.1 (22050)
HZB70L-ZGMNSV 22.1 (22050)



b.

Install SST to the front and rear wheel cylinders.

SST
09709-29018  



d.

Measure the rear wheel cylinder fluid pressure.

i.

Raise the front wheel cylinder fluid pressure to 7.9 MPa (80.0 kgf/cm2) by pressing the brake pedal, and measure the rear wheel cylinder fluid pressure.

Standard rear wheel cylinder pressure:

5.9 MPa (60.0 +/-5.0 kgf/cm2)


NOTICE:
·

The pedal should not be depressed twice or released while the front wheel cylinder fluid pressure is being set.

·

Read the value of the rear wheel cylinder fluid pressure after adjusting and holding the front wheel cylinder fluid pressure for 2 seconds.





Hide 2.ADJUST LOAD SENSING W/SPRING VALVE ASSEMBLY

a.
C148731E02
2.688,1.688 2.406,1.688 2.406,1.688 2.208,1.24 false 1.063,1.125 1.219,1.323 0.156,0.198 10 false A 2.75,1.615 2.906,1.813 0.156,0.198 10 false *1

Adjust the length of the No. 2 load sensing spring shackle.

Text in Illustration
*1 Lock Nut

·

Low pressure - Lengthen A

·

High pressure - Shorten A


Standard initial length A:

90 mm (3.54 in.)


Standard length after adjustment A:

84 to 96 mm (3.30 to 3.77 in.)


HINT:

One turn of the No. 2 shackle nut changes the fluid pressure to about the following specifications.


Standard pressure change:

Changes by 0.13 MPa (1.3 kgf/cm2, 18.9 psi) for one turn lock nut change in length



b.

Tighten the lock nut.

Torque:

12.5 N*m (127 kgf*cm, 9 ft.*lbf)


HINT:

If the pressure cannot be adjusted by the No. 2 load sensing spring shackle, raise or lower the load sensing proportioning valve.



c.
C392433

Loosen the 2 nuts.


d.

Adjust the load sensing proportioning valve position.

·

Low pressure - Lower

·

High pressure - Raise



e.

Tighten the nuts.

Torque:

12.5 N*m (127 kgf*cm, 9 ft.*lbf)



f.

Adjust the length of the No. 2 load sensing spring shackle again. If it cannot be adjusted, inspect the load sensing proportioning valve.


g.

Remove SST.



i.

Inspect for brake fluid leaks.


Hide 3. CHECK VALVE BODY

a.

Check that the master cylinder rear brake fluid pressure changes according to the rear wheel cylinder pressure.

Standard Pressure:
Master Cylinder Pressure Wheel Cylinder Pressure
4900 kPa (50 kgf/cm2, 711psi) 2930 kPa +/-200 kPa (30 +/-2 kgf/cm2, 425 +/-29 psi)
9810 kPa (100 kgf/cm2, 1422psi) 4740 kPa +/-400 kPa (48 +/-4 kgf/cm2, 687 psi +/-58 psi)