Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY(for Parking Brake Drum with Inner Diameter of 160 mm)
RM2850E _54 Brake _073229 PARKING BRAKE _0356452 PARKING BRAKE ASSEMBLY(for Parking Brake Drum with Inner Diameter of 160 mm) A

PARKING BRAKE  PARKING BRAKE ASSEMBLY(for Parking Brake Drum with Inner Diameter of 160 mm)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Do not reuse any parts that have been dropped.


PROCEDURE

Hide 46501A 1.REPLACE PARKING BRAKE DRUM SERRATION BOLT

a.
C139330

Using a press, remove the parking brake drum serration bolts.


b.
C139331

Install a washer and service nut to a new parking brake drum serration bolt as shown in the illustration.

Recommended service nut:
Thread diameter:

11.0 mm (0.433 in.)

Thread pitch:

1.0 mm (0.0394 in.)



c.

Using a brass bar or an equivalent tool to hold the parking brake drum, install the parking brake drum serration bolt by tightening the nut.

NOTICE:
·

Install the nuts to prevent damage to the parking brake drum serration bolts.

·

Do not damage the threads of the parking brake drum serration bolts.




Hide 2.APPLY HIGH TEMPERATURE GREASE

a.
C244855E01
0.379,1.889 0.581,2.041 0.202,0.152 10 *1

Apply high temperature grease to the surface of the parking brake plate which is in contact with the shoe.

Text in Illustration
*1 High Temperature Grease


Hide 46601 3.INSTALL PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

a.
C061405

Install the parking brake shoe lever to the parking brake shoe with 2 new C-washers.


Hide 46506A 4.INSTALL PARKING BRAKE SHOE ADJUSTER SUB-ASSEMBLY

a.

Install the parking brake shoe adjuster to the parking brake plate.


Hide 5.INSTALL PARKING BRAKE SHOE

a.
C061398

Using needle-nose pliers, connect the No. 1 parking brake cable assembly to the parking brake shoe lever.


b.

Install the parking brake shoe to the parking brake plate.


Hide 46556 6.INSTALL SHOE HOLD DOWN SPRING PIN

a.

Install the 2 shoe hold down spring pins and the 2 shoe hold down springs.


Hide 7.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING

a.
C403499E01
2.333,0.771 2.625,0.354 true 2.677,0.25 3.135,0.448 0.458,0.198 10 false SST

Using SST, install the parking brake shoe return tension spring on the lower side.

SST
09703-30011  


b.

Install the plate washer.


c.
C403501E01
1.969,1 2.51,0.49 true 0.333,0.625 1.281,0.854 true 1.531,0.771 2.281,0.26 true 2.563,0.385 3.021,0.583 0.458,0.198 10 false SST 2.302,0.083 2.76,0.281 0.458,0.198 10 false 1 0.177,0.542 0.635,0.74 0.458,0.198 10 false 2

Using SST, install the 2 parking brake shoe return tension springs in the order shown in the illustration.

SST 09178-20010


Hide 8. PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

C249504E01
0.482,0.363 0.69,0.609 0.208,0.246 10 *A 3.91,0.363 4.119,0.609 0.208,0.246 10 *B

Text in Illustration
*A for LHD *B for RHD


Hide 46501 9.INSTALL PARKING BRAKE DRUM SUB-ASSEMBLY

a.

Install the parking brake drum.

NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining or the drum.



b.

Apply a light coat of MP grease to a new O-ring, and install the O-ring and new nut to the parking brake drum.


c.

Using a socket wrench 32 mm, temporarily tighten the nut.


d.
C403517E01
1.906,1.781 2.219,1.979 0.313,0.198 10 false *a 2.802,1.021 3.115,1.219 0.313,0.198 10 false *b

Turn the shoe adjuster counterclockwise to expand the shoe until the drum locks.

Text in Illustration
*a Contract
*b Expand


e.

Turn the shoe adjuster clockwise 1 notch.


f.

With the parking brake lever pulled its full distance, check to see that the drum is locked.


g.

Release the parking brake lever and ensure that the parking brake does not drag.

If it drags, contract the shoe adjuster clockwise another notch.


h.

Pull the parking brake lever.


i.

Tighten the nut to the parking brake drum.

Torque:

127N*m (1299kgf*cm, 94 ft.*lbf)



j.
C151903

Using a chisel and a hammer, stake the nut.


k.

Release the parking brake lever.


Hide 10.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 11.INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL