Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY (for Parking Brake Drum with Inner Diameter of 200 mm)
RM2850E _54 Brake _073229 PARKING BRAKE _0356453 PARKING BRAKE ASSEMBLY(for Parking Brake Drum with Inner Diameter of 200 mm) A

PARKING BRAKE  PARKING BRAKE ASSEMBLY(for Parking Brake Drum with Inner Diameter of 200 mm)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 46501 2.REMOVE PARKING BRAKE DRUM SUB-ASSEMBLY

a.

Pull the parking brake lever.


b.
C151879E01
2.658,1.116 3.268,1.376 0.609,0.26 10 SST 2.609,0.872 2.814,1.116 false

Using SST and a hammer, release the staked part of the nut.

SST
09930-00010  

NOTICE:
·

Insert SST into the groove with the flat surface facing up.

·

Do not damage the tip of SST using a grinder.

·

Completely unstake the staked part before removing the nut.

·

Do not damage the threads of the output shaft.




c.
C151880

Using a socket wrench 32 mm, remove the nut.


d.
C151881

Using a screwdriver, remove the O-ring.


e.

Release the parking brake lever and remove the parking brake drum.

HINT:

If the parking brake drum cannot be removed easily, perform the following procedure.



f.
C244858E02
1.604,1.354 1.865,1.573 0.26,0.219 10 true *a

Remove the parking brake shoe adjusting hole plug and insert a screwdriver through the hole into the parking brake drum, and turn the shoe adjuster until the parking brake drum turns freely.

Text in Illustration
*a Contract


Hide 46201B 3.REMOVE TENSION SPRING

a.
C244859E02
2.052,0.552 2.656,0.25 true 2.708,0.146 3.115,0.427 0.406,0.281 10 true SST

Using SST, remove the 2 tension springs.

SST
09717-20010  


Hide 4.REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING

a.

for Type-A:

i.
C151884

Using needle-nose pliers, remove the 2 parking brake shoe return tension springs.



b.
C249437

for Type-B RHD:

i.

Using needle-nose pliers, remove the parking brake shoe return tension spring.



Hide 46556 5.REMOVE SHOE HOLD DOWN SPRING PIN

a.

Remove the 4 brake shoe hold down cups, 2 shoe hold down springs and the 2 shoe hold down spring pins.


Hide 47456A 6.REMOVE PARKING BRAKE SHOE GUIDE PLATE

a.
C244849

Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.


Hide 7.REMOVE PARKING BRAKE SHOE

a.
C249443

Remove the parking brake shoe from the parking brake plate.


Hide 46405A 8.REMOVE SHOE ADJUSTING SCREW SET RH

a.
C249444

Using needle-nose pliers, remove the parking brake shoe return tension spring.


b.
C151889

Remove the shoe adjusting screw set.


Hide 46612 9.REMOVE PARKING BRAKE SHOE LEVER STRUT

a.

for Type-A:

i.
C151890

Remove the parking brake shoe lever strut and the parking brake shoe strut compression spring.


ii.

Using needle-nose pliers, remove the parking brake shoe return tension spring.



b.

for Type-B:

i.
C151891

Remove the parking brake shoe lever strut and the parking brake shoe strut compression spring.



Hide 10. DISCONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.
C151892

Using needle-nose pliers, disconnect the No. 1 parking brake cable assembly.


Hide 46601 11.REMOVE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

a.
C151893

Using a screwdriver, remove the C-washer and the parking brake shoe lever from the parking brake shoe.