Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Yaw Rate Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Yaw Rate Sensor Communication Stop Mode Either condition is met:
·

Communication stop for "Yaw Rate Sensor" is indicated on the "Communication Bus Check" screen of the GTS (Click here(Click here))

·

Communication stop history for "Yaw Rate Sensor" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Yaw Rate Sensor" is 6 or more.) (Click here(Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Yaw Rate Sensor Communication Stop Mode" in "DTC Combination Table" (Click here(Click here))


·

Yaw rate sensor CAN branch wire or connector

·

Power source circuit of yaw rate sensor

·

Yaw rate sensor ground circuit

·

Yaw rate sensor



WIRING DIAGRAM

C241189E44
0.104,1.365 0.563,1.563 0.458,0.198 10 false A80 0.094,1.552 1.792,1.823 1.698,0.271 10 false No. 3 Junction Connector 3.031,1.875 4.177,2.083 1.146,0.208 10 false ECU-IG1 NO.3 1.021,2.021 2.479,2.302 1.458,0.281 10 false from IG1-NO.1 Relay 1.625,0.49 1.938,0.688 0.313,0.198 10 false 10 1.677,1.083 1.99,1.281 0.313,0.198 10 false 5 5.385,0.5 5.698,0.698 0.313,0.198 10 false 3 5.385,1.063 5.698,1.26 0.313,0.198 10 false 2 5.396,1.948 5.708,2.146 0.313,0.198 10 false 4 5.406,2.521 5.719,2.719 0.313,0.198 10 false 1 5.594,0.594 6.208,0.792 0.615,0.198 10 false CANH 5.583,1.188 6.198,1.385 0.615,0.198 10 false CANL 5.594,2.052 6.208,2.25 0.615,0.198 10 false IG 5.594,2.646 6.208,2.844 0.615,0.198 10 false GND 5.354,3.271 5.813,3.469 0.458,0.198 10 false A72 5.344,3.458 6.563,3.729 1.219,0.271 10 false Yaw Rate Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 61 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR CAN BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the yaw rate sensor connector.


c.
C371314E01
1.469,0.25 1.875,0.49 0.406,0.24 1.25,1.865 1.458,1.865 1.458,1.865 1.458,1.115 true 1.823,1.875 1.635,1.875 1.635,1.875 1.635,1.125 true 1.552,0.281 1.938,0.51 0.385,0.229 10 false A72 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.833,1.792 1.448,1.99 0.615,0.198 10 false CANL 1.896,1.792 2.51,1.99 0.615,0.198 10 false CANH

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-3 (CANH) - A72-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor)


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.
C371314E02
1.469,0.229 1.833,0.5 0.365,0.271 1.188,1.813 1.344,1.813 1.344,1.813 1.344,1.125 true 1.927,1.823 1.75,1.823 1.75,1.823 1.75,1.135 true 1.521,0.271 1.979,0.469 0.458,0.198 10 false A72 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.844,1.74 1.458,1.938 0.615,0.198 10 false GND 1.99,1.74 2.604,1.938 0.615,0.198 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor)

Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR