Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM T

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result List of How to Proceed with Troubleshooting
Symptom Suspected Area See page
Either of the following:
·

The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 2.

·

Resistance between CAN bus lines (CANH and CANL) in Bus 2 is 70 Ω or more.


Open in Bus 2 Main Bus Line (Click here)
Either of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 2 is suspected.

·

Resistance between CAN bus lines (CANH and CANL) in Bus 2 is below 54 Ω.


Check Bus 2 Lines for Short Circuit (Click here)
Any of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 2 is suspected.

·

Resistance between CANH and +B in Bus 2 is below 6 kΩ.

·

Resistance between CANL and +B in Bus 2 is below 6 kΩ.


Check Bus 2 Line for Short to +B (Click here)
Any of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 2 is suspected.

·

Resistance between CANH and ground in Bus 2 is below 200 Ω.

·

Resistance between CANL and ground in Bus 2 is below 200 Ω.


Check Bus 2 Line for Short to GND (Click here)
Either of the following:
·

The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 4.

·

Resistance between CAN bus lines (CANH and CANL) in Bus 4 is 70 Ω or more.


Open in Bus 4 Main Bus Line (Click here)
Either of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 4 is suspected.

·

Resistance between CAN bus lines (CANH and CANL) in Bus 4 is below 54 Ω.


Check Bus 4 Lines for Short Circuit (Click here)
Any of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 4 is suspected.

·

Resistance between CANH and +B in Bus 4 is below 6 kΩ.

·

Resistance between CANL and +B in Bus 4 is below 6 kΩ.


Check Bus 4 Line for Short to +B (Click here)
Any of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 4 is suspected.

·

Resistance between CANH and ground in Bus 4 is below 200 Ω.

·

Resistance between CANL and ground in Bus 4 is below 200 Ω.


Check Bus 4 Line for Short to GND (Click here)
Resistance between CANH and CANL is normal in Bus 4 and the problem symptom pattern in How to Use "Communication Bus Check" Screen in Inspection matches the symptoms when there is an open in one wire of a branch line in Bus 4. Open in One Side of Bus 4 Branch Line (Click here)
Either of the following:
·

The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 5.

·

Resistance between CAN bus lines (CANH and CANL) in Bus 5 is 70 Ω or more.


Open in Bus 5 Main Bus Line (Click here)
Either of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 5 is suspected.

·

Resistance between CAN bus lines (CANH and CANL) in Bus 5 is below 54 Ω.


Check Bus 5 Lines for Short Circuit (Click here)
Any of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 5 is suspected.

·

Resistance between CANH and +B in Bus 5 is below 6 kΩ.

·

Resistance between CANL and +B in Bus 5 is below 6 kΩ.


Check Bus 5 Line for Short to +B (Click here)
Any of the following:
·

The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 5 is suspected.

·

Resistance between CANH and ground in Bus 5 is below 200 Ω.

·

Resistance between CANL and ground in Bus 5 is below 200 Ω.


Check Bus 5 Line for Short to GND (Click here)

HINT:

The suspected communication stop area can be determined based on the ECUs or sensors that are displayed as not communicating on the "Communication Bus Check" screen or "Communication Bus Check (Detail)" screen and by referring to the following table.


Communication Stop Mode Table (Open in bus line or other communication stop)
Symptom Suspected Area See page
Either of the following is met:
·

Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.

·

Communication stop history for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Skid Control (ABS/VSC/TRAC)" is 6 or more.)


Skid Control ECU Communication Stop Mode (Click here)
Either of the following is met:
·

Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS.

·

Communication stop history for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Spiral cable (Steering Angle Sensor)" is 6 or more.)


Steering Angle Sensor Communication Stop Mode (Click here)
Either of the following is met:
·

Communication stop for "Yaw Rate Sensor" is indicated on the "Communication Bus Check" screen of the GTS.

·

Communication stop history for "Yaw Rate Sensor" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Yaw Rate Sensor" is 6 or more.)


Yaw Rate Sensor Communication Stop Mode (Click here)
Either of the following is met:
·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.

·

Communication stop history for "ECM (Engine)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "ECM (Engine)" is 6 or more.)


ECM Communication Stop Mode (Click here)
Either of the following is met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

·

Communication stop history for "Combination Meter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Combination Meter" is 6 or more.)


Combination Meter ECU Communication Stop Mode (Click here)
Either of the following is met:
·

Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the GTS.

·

Communication stop history for "Airbag" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Airbag" is 6 or more.)


Center Airbag Sensor Communication Stop Mode (Click here)

DTC Combination Table
Symptom Suspected Area See page
Although CAN communication is currently normal, ECUs connected to each bus store CAN communication DTCs. The probable part for which communication is interrupted can be determined using DTC Combination Table and comparing the DTCs output from ECUs connected to the CAN communication system. (Click here)