Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Open in Bus 4 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 4 main lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Detection Item Trouble Area

*1: w/ Airbag System

*2: w/o Airbag System

*3: for LHD

*4: for RHD

Resistance between terminals 22 (CA2H) and 7 (CA2L) of central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main wire or connector

·

Central gateway ECU (network gateway ECU)

·

Airbag ECU assembly*1

·

No. 3 CAN junction connector

·

No. 3 junction connector*2

·

No. 63 junction connector*3

·

No. 67 junction connector*4

·

No. 1 CAN junction terminal*2



This malfunction is not related to the lines of a bus 4 branch or to ECUs or sensors connected a bus 4 branch.

WIRING DIAGRAM

C400814E01
2.365,1.104 3.74,1.302 1.375,0.198 10 false 6*3, 18*4 2.427,0.583 3.802,0.781 1.375,0.198 10 false 3*3, 7*4 3.635,0.573 5.01,0.771 1.375,0.198 10 false 1*3, 5*4 3.656,1.115 5.031,1.313 1.375,0.198 10 false 4*3, 16*4 2.396,1.51 3.771,1.708 1.375,0.198 10 false J90*3, J81*4 2.385,1.688 4.208,2.042 1.823,0.354 10 false No. 63 Junction Connector*3, No. 67 Junction Connector*4 5.5,1.5 6.052,1.677 0.552,0.177 10 false J51 5.5,1.677 7.01,2.052 1.51,0.375 10 false Central Gateway ECU (Network Gateway ECU) 5.948,0.573 6.615,0.74 0.667,0.167 10 false CA2H 5.948,1.292 6.667,1.542 0.719,0.25 10 false CA2L 5.938,3.156 6.563,3.344 0.625,0.188 10 false CANH 5.958,3.854 6.448,4.052 0.49,0.198 10 false CANL 5.396,4.083 6.771,4.281 1.375,0.198 10 false A58 5.396,4.292 6.906,4.51 1.51,0.219 10 false Airbag ECU Assembly 2.115,2.563 3.594,2.781 1.479,0.219 12 false w/ Airbag System: 2.115,5.177 3.823,5.438 1.708,0.26 12 false w/o Airbag System: 2.708,6.698 4.083,6.896 1.375,0.198 10 false A80 2.708,6.896 4.5,7.115 1.792,0.219 10 false No. 3 Junction Connector 5.469,6.729 6.844,6.927 1.375,0.198 10 false A76 5.469,6.896 6.74,7.24 1.271,0.344 10 false No. 1 CAN Junction Terminal 5.938,5.729 6.469,5.927 0.531,0.198 10 false CANH 5.948,6.438 6.417,6.656 0.469,0.219 10 false CANL 0.198,6.781 1.573,6.979 1.375,0.198 10 false A91 0.188,6.969 1.417,7.354 1.229,0.385 10 false No. 3 CAN Junction Connector 0.135,7.781 1.594,7.979 1.458,0.198 10 false *1: w/ Airbag System 0.135,8.115 1.781,8.333 1.646,0.219 10 false *2: w/o Airbag System 0.135,8.458 1.51,8.656 1.375,0.198 10 false *3: for LHD 1.135,8.458 2.51,8.656 1.375,0.198 10 false *4: for RHD 1.115,5.719 2.49,5.917 1.375,0.198 10 false 6*2 1.125,6.271 2.5,6.469 1.375,0.198 10 false 8*2 2.854,5.74 3.177,5.948 0.323,0.208 10 false 9 2.865,6.271 3.188,6.479 0.323,0.208 10 false 4 3.625,5.74 3.948,5.948 0.323,0.208 10 false 11 3.646,6.271 3.969,6.479 0.323,0.208 10 false 6 5.76,5.74 6.083,5.948 0.323,0.208 10 false 3 5.771,6.271 6.094,6.479 0.323,0.208 10 false 2 5.698,3.677 6.021,3.885 0.323,0.208 10 false 22 5.688,3.156 6.01,3.365 0.323,0.208 10 false 13 1.125,3.156 1.448,3.365 0.323,0.208 10 false 5*1 1.125,3.698 1.448,3.906 0.323,0.208 10 false 7*1 1.125,0.573 1.448,0.781 0.323,0.208 10 false 1 1.135,1.104 1.458,1.313 0.323,0.208 10 false 3 5.698,0.573 6.021,0.781 0.323,0.208 10 false 22 5.76,1.104 6.083,1.313 0.323,0.208 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.
C358902E02
1.49,0.188 1.875,0.438 0.385,0.25 1.375,0.969 1.031,0.646 1.031,0.646 0.865,0.646 true 1.792,0.917 2.021,0.469 2.021,0.469 2.188,0.469 true 1.396,1.302 1.208,1.667 1.208,1.667 1.042,1.667 true 1.615,1.302 1.344,1.917 1.344,1.917 1.177,1.917 true 1.813,1.292 2.167,1.927 2.167,1.927 2.333,1.927 true 2,1.281 2.24,1.667 2.24,1.667 2.406,1.667 true 0.302,0.573 1.219,0.771 0.917,0.198 10 false CANH*b 2.26,0.385 3.177,0.583 0.917,0.198 10 false CANL*b 2.469,1.573 3.385,1.771 0.917,0.198 10 false CANL*d 2.406,1.854 3.323,2.052 0.917,0.198 10 false CANL*c 0.604,1.844 1.521,2.042 0.917,0.198 10 false CANH*d 0.469,1.583 1.385,1.781 0.917,0.198 10 false CANH*c 0.073,0.073 0.99,0.271 0.917,0.198 10 false *a 1.563,0.229 2.479,0.427 0.917,0.198 10 false A91

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: for LHD

*2: for RHD

*3: w/ Airbag System

*4: w/o Airbag System

A91-1 (CANH) - A91-3 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
·

No. 63 junction connector*1

·

No. 67 junction connector*2


A91-5 (CANH) - A91-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Airbag ECU assembly*3
A91-6 (CANH) - A91-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 junction connector*4


Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b
·

to No. 63 Junction Connector (for LHD)

·

to No. 67 Junction Connector (for RHD)


*c to Airbag ECU Assembly (w/ Airbag System)
*d to No. 3 Junction Connector (w/o Airbag System)


Result:
Result Proceed to
OK A
NG (No. 63 junction connector CAN main wire [for LHD]) B
NG (No. 67 junction connector CAN main wire [for RHD]) C
NG (Airbag ECU assembly CAN main wire [w/ Airbag System]) D
NG (No. 3 junction connector CAN main wire [w/o Airbag System]) E



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 63 JUNCTION CONNECTOR)

C

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 67 JUNCTION CONNECTOR)

D

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

E

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 63 JUNCTION CONNECTOR)
a.

Reconnect the A91 No. 3 CAN junction connector.


b.

Disconnect the No. 63 junction connector.


c.
C358905E10
0.292,1.083 0.604,1.344 0.313,0.26 1.281,1.042 0.958,0.375 0.958,0.375 0.792,0.375 true 0.99,1.063 0.75,0.844 0.75,0.844 0.594,0.844 true 1.469,1.052 1.688,0.167 1.688,0.167 1.833,0.167 true 1.729,1.052 1.938,0.479 1.938,0.479 2.094,0.479 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 0.24,0.302 1.156,0.5 0.917,0.198 10 false CANH*c 0.031,0.76 0.948,0.958 0.917,0.198 10 false CANH*b 1.906,0.094 2.823,0.292 0.917,0.198 10 false CANL*b 2.156,0.396 3.073,0.594 0.917,0.198 10 false CANL*c 0.333,1.125 0.792,1.323 0.458,0.198 10 false J90

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J90-1 (CANH) - J90-4 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
J90-3 (CANH) - J90-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction connector


Text in Illustration
*a Front view of wire harness connector
(to No. 63 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 3 CAN Junction Connector


Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C



A

REPLACE NO. 63 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 63 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 67 JUNCTION CONNECTOR)
a.

Reconnect the A91 No. 3 CAN junction connector.


b.

Disconnect the No. 67 junction connector.


c.
C358905E11
0.146,0.979 0.5,1.229 0.354,0.25 1.552,1.073 1.177,0.333 1.177,0.333 1.031,0.333 true 1.844,1.063 2.156,0.323 2.156,0.323 2.344,0.323 true 1.573,1.333 1.427,1.813 1.427,1.813 1.188,1.813 true 1.854,1.313 2.177,1.854 2.177,1.854 2.344,1.854 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 0.469,0.25 1.063,0.469 0.594,0.219 10 false CANH*b 2.438,0.25 3.031,0.469 0.594,0.219 10 false CANH*c 2.438,1.771 3.031,1.99 0.594,0.219 10 false CANL*c 0.615,1.729 1.208,1.948 0.594,0.219 10 false CANL*b 0.219,1.021 0.813,1.24 0.594,0.219 10 false J81

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J81-5 (CANH) - J81-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
J81-7 (CANH) - J81-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction connector


Text in Illustration
*a Front view of wire harness connector
(to No. 67 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 3 CAN Junction Connector


Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C



A

REPLACE NO. 67 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 67 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU - NO. 67 JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)
a.

Reconnect the J90 No. 63 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C368242E02
1.51,0.406 1.865,0.646 0.354,0.24 2.229,1.083 2.229,0.521 2.229,0.521 2.375,0.521 true 2.156,1.313 2.156,1.865 2.156,1.865 2.292,1.865 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 2.448,0.448 3.063,0.646 0.615,0.198 10 false CA2L 2.365,1.792 2.979,1.99 0.615,0.198 10 false CA2H 1.573,0.438 2.188,0.635 0.615,0.198 10 false J51

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-22 (CA2H) - J51-7 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU - NO. 67 JUNCTION CONNECTOR)
a.

Reconnect the J81 No. 67 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C368242E03
1.5,0.396 1.885,0.667 0.385,0.271 2.25,1.073 2.25,0.5 2.25,0.5 2.417,0.5 true 2.292,1.865 2.156,1.865 2.156,1.865 2.156,1.281 true 2.479,0.427 3.094,0.625 0.615,0.198 10 false CA2L 2.375,1.781 2.99,1.979 0.615,0.198 10 false CA2H 1.573,0.438 2.188,0.635 0.615,0.198 10 false J51 0.125,0.094 0.74,0.292 0.615,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-22 (CA2H) - J51-7 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 67 JUNCTION CONNECTOR)

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the A91 No. 3 CAN junction connector.



c.
C227515E14
0.167,0.927 0.594,1.219 0.427,0.292 2.01,1.021 2.563,0.708 2.563,0.708 2.719,0.708 true 2.104,1.365 2.552,1.792 2.552,1.792 2.719,1.792 true 2.813,1.719 3.427,1.917 0.615,0.198 10 false CANL 2.802,0.646 3.417,0.844 0.615,0.198 10 false CANH 0.25,0.979 0.865,1.177 0.615,0.198 10 false A58 0.094,0.083 0.708,0.281 0.615,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-13 (CANH) - A58-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Airbag ECU Assembly)


Result:
Proceed to
OK
NG



OK

NG

REPLACE CAN MAIN WIRE AND CONNECTOR (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the A91 No. 3 CAN junction connector.


b.

Disconnect the No. 3 junction connector.


c.
C358905E12
0.177,1.01 0.594,1.271 0.417,0.26 1.438,1.052 1.438,0.354 1.438,0.354 1.281,0.354 true 1.719,1.052 1.719,0.167 1.719,0.167 1.563,0.167 true 2.115,1.052 2.115,0.167 2.115,0.167 2.292,0.167 true 2.396,1.063 2.396,0.365 2.396,0.365 2.573,0.365 true 2.354,0.094 3.271,0.292 0.917,0.198 10 false CANH*b 2.635,0.302 3.292,0.49 0.656,0.188 10 false CANH*c 1.021,0.073 1.938,0.271 0.917,0.198 10 false CANL*c 0.729,0.271 1.646,0.469 0.917,0.198 10 false CANL*b 0.25,1.052 1.167,1.25 0.917,0.198 10 false A80 0.073,0.083 0.99,0.281 0.917,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A80-9 (CANH) - A80-4 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction connector
A80-11 (CANH) - A80-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction terminal


Text in Illustration
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b to No. 3 CAN Junction Connector
*c to No. 1 CAN Junction Terminal


Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (No. 1 CAN junction terminal CAN main wire) C



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION TERMINAL)

C

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 3 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the A80 No. 3 junction connector.


b.

Disconnect the No. 1 CAN junction terminal connector.


c.
C300866E20
0.167,0.844 0.573,1.146 0.406,0.302 1.344,0.708 1.031,0.458 1.031,0.458 0.875,0.458 true 1.698,0.708 1.469,0.188 1.469,0.188 1.302,0.188 true 0.448,0.385 1.063,0.583 0.615,0.198 10 false CANH 0.906,0.104 1.521,0.302 0.615,0.198 10 false CANL 0.24,0.906 0.854,1.104 0.615,0.198 10 false A76 0.073,0.073 0.688,0.271 0.615,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A76-3 (CANH) - A76-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION TERMINAL - NO. 3 JUNCTION CONNECTOR)