There may be an open circuit in one of the bus 5 main lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
| Detection Item | Trouble Area |
|---|---|
|
*1: for LHD *2: for RHD |
|
| Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU (network gateway ECU) is 70 Ω or higher. | ·
CAN main wire or connector ·
Central gateway ECU (network gateway ECU) ·
Combination meter assembly ·
No. 59 junction connector*1 ·
No. 68 junction connector*2 |
This malfunction is not related to the lines of a bus 5 branch or to ECUs or sensors connected a bus 5 branch.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and DTC may be stored.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 59 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| J86-8 (CANH) - J86-5 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| J86-9 (CANH) - J86-6 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| *a | Front view of wire harness connector
(to No. 59 Junction Connector) |
| *b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to Combination Meter Assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (Combination meter assembly CAN main wire) | C |
A
B
C
Reconnect the J86 No. 59 junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-15 (CA5H) - J51-16 (CA5L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the J86 No. 59 junction connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-23 (CANH) - J1-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 68 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| J76-5 (CANH) - J76-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| J76-6 (CANH) - J76-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| *a | Front view of wire harness connector
(to No. 68 Junction Connector) |
| *b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to Combination Meter Assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (Combination meter assembly CAN main wire) | C |
A
B
C
Reconnect the J76 No. 68 junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-15 (CA5H) - J51-16 (CA5L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the J76 No. 68 junction connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-23 (CANH) - J1-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG