Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Check Bus 5 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 5 CAN main wires when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Detection Item Trouble Area

*1: for LHD

*2: for RHD

Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main wires

·

Central gateway ECU (network gateway ECU)

·

Combination meter assembly

·

No. 59 junction connector*1

·

No. 68 junction connector*2



WIRING DIAGRAM

C371311E05
0.823,0.365 1.438,0.563 0.615,0.198 10 false CA5H 0.865,1.094 1.479,1.292 0.615,0.198 10 false CA5L 5.948,0.385 6.563,0.583 0.615,0.198 10 false CANH 5.958,1.073 6.573,1.271 0.615,0.198 10 false CANL 2.833,0.365 4.063,0.563 1.229,0.198 10 false 8*1, 5*2 2.781,0.917 4.01,1.115 1.229,0.198 10 false 5*1, 16*2 3.823,0.375 5.052,0.573 1.229,0.198 10 false 9*1, 6*2 3.833,0.906 5.063,1.104 1.229,0.198 10 false 6*1, 17*2 0.188,1.438 1.417,1.635 1.229,0.198 10 false J51 0.167,1.635 1.688,2.01 1.521,0.375 10 false Central Gateway ECU (Network Gateway ECU) 0.146,2.406 1.375,2.604 1.229,0.198 10 false *1: for LHD 1.219,2.406 2.448,2.604 1.229,0.198 10 false *2: for RHD 2.604,1.385 3.833,1.583 1.229,0.198 10 false J86*1, J76*2 2.594,1.573 4.375,1.927 1.781,0.354 10 false No. 59 Junction Connector*1, No. 68 Junction Connector*2 5.594,1.354 6.823,1.552 1.229,0.198 10 false J1 5.594,1.542 6.771,1.885 1.177,0.344 10 false Combination Meter Assembly 1.313,0.375 1.625,0.573 0.313,0.198 10 false 15 1.323,0.906 1.635,1.104 0.313,0.198 10 false 16 5.708,0.375 6.021,0.573 0.313,0.198 10 false 23 5.719,0.917 6.031,1.115 0.313,0.198 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT IN CAN BUS WIRES (NO. 59 JUNCTION CONNECTOR)

B

5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 68 JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS WIRES (NO. 59 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 59 junction connector.


c.
C358905E21
0.208,0.969 0.573,1.229 0.365,0.26 1.708,1.042 1.708,0.219 1.708,0.219 1.531,0.219 true 1.979,1.031 1.979,0.219 1.979,0.219 2.135,0.219 true 2.104,1.042 2.104,0.438 2.104,0.438 2.26,0.438 true 1.573,1.031 1.573,0.427 1.573,0.427 1.396,0.427 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.281,1.01 0.594,1.208 0.313,0.198 10 false J86 0.865,0.354 1.448,0.542 0.583,0.188 10 false CANL*b 1,0.115 1.583,0.302 0.583,0.188 10 false CANL*c 2.208,0.125 2.792,0.313 0.583,0.188 10 false CANH*b 2.333,0.354 2.917,0.542 0.583,0.188 10 false CANH*c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J86-8 (CANH) - J86-5 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
J86-9 (CANH) - J86-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly


Text in Illustration
*a Front view of wire harness connector
(to No. 59 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Combination Meter Assembly


Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (Combination meter assembly CAN main wire) C



A

REPLACE NO. 59 JUNCTION CONNECTOR

B

3.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU - NO. 59 JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 59 JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU - NO. 59 JUNCTION CONNECTOR)
a.

Reconnect the J86 No. 59 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C368242E09
1.5,0.406 1.854,0.646 0.354,0.24 1.573,1.302 1.573,1.854 1.573,1.854 1.708,1.854 true 1.469,1.302 1.469,1.854 1.469,1.854 1.313,1.854 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.781,1.771 2.396,1.969 0.615,0.198 10 false CA5L 0.896,1.771 1.51,1.969 0.615,0.198 10 false CA5H 1.573,0.438 2.188,0.635 0.615,0.198 10 false J51

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J51-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 59 JUNCTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 59 JUNCTION CONNECTOR)
a.

Reconnect the J86 No. 59 junction connector.


b.
C358908E06
1.5,0.333 1.865,0.573 0.365,0.24 0.625,1.802 0.771,1.802 0.771,1.802 0.771,1.281 true 1.052,1.802 0.896,1.802 0.896,1.802 0.896,1.281 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.219,1.729 0.833,1.927 0.615,0.198 10 false CANL 1.115,1.719 1.729,1.917 0.615,0.198 10 false CANH 1.604,0.375 1.917,0.573 0.313,0.198 10 false J1

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-23 (CANH) - J1-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 59 JUNCTION CONNECTOR)

5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 68 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 68 junction connector.


c.
C358905E22
0.198,0.938 0.573,1.198 0.375,0.26 1.292,1.844 1.448,1.844 1.448,1.844 1.583,1.344 true 1.563,1.042 1.302,0.365 1.302,0.365 1.156,0.365 true 1.708,1.063 1.958,0.375 1.958,0.375 2.156,0.375 true 1.74,1.344 1.927,1.833 1.927,1.833 2.104,1.833 true 0.271,0.979 0.729,1.177 0.458,0.198 10 false J76 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 2.167,1.75 3.083,1.948 0.917,0.198 10 false CANL*c 0.729,1.76 1.646,1.958 0.917,0.198 10 false CANL*b 0.583,0.292 1.5,0.49 0.917,0.198 10 false CANH*b 2.229,0.292 3.146,0.49 0.917,0.198 10 false CANH*c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J76-5 (CANH) - J76-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
J76-6 (CANH) - J76-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly


Text in Illustration
*a Front view of wire harness connector
(to No. 68 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Combination Meter Assembly


Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (Combination meter assembly CAN main wire) C



A

REPLACE NO. 68 JUNCTION CONNECTOR

B

6.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 68 JUNCTION CONNECTOR)
6.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)
a.

Reconnect the J76 No. 68 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C368242E10
1.5,0.406 1.854,0.646 0.354,0.24 1.573,1.302 1.573,1.854 1.573,1.854 1.708,1.854 true 1.469,1.302 1.469,1.854 1.469,1.854 1.313,1.854 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.781,1.771 2.396,1.969 0.615,0.198 10 false CA5L 0.896,1.771 1.51,1.969 0.615,0.198 10 false CA5H 1.573,0.438 2.188,0.635 0.615,0.198 10 false J51

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J51-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)

7.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 68 JUNCTION CONNECTOR)
a.

Reconnect the J76 No. 68 junction connector.


b.
C358908E07
1.5,0.333 1.865,0.573 0.365,0.24 0.625,1.802 0.771,1.802 0.771,1.802 0.771,1.281 true 1.052,1.802 0.896,1.802 0.896,1.802 0.896,1.281 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.219,1.729 0.833,1.927 0.615,0.198 10 false CANL 1.115,1.719 1.729,1.917 0.615,0.198 10 false CANH 1.604,0.375 1.917,0.573 0.313,0.198 10 false J1

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-23 (CANH) - J1-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 68 JUNCTION CONNECTOR)