Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1225  SM Solenoid Circuit  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. DTC Detection Condition Trouble Area
C1225 Either of the following is detected:
1.

While master cylinder cut solenoid (SM1 or SM2) outputs ON, overcurrent continues for 0.1 seconds or more.

2.

While master cylinder cut solenoid (SM1 or SM2) outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While master cylinder cut solenoid (SM1 or SM2) outputs ON, open circuit continues for 0.05 seconds or more.

4.

While master cylinder cut solenoid (SM1 or SM2) outputs OFF, current is maintained for 0.05 seconds or more.

5.

Difference in master cylinder cut solenoids (SM1 and SM2) output accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C1468
C1469
C146A
C146B
Either of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly

WIRING DIAGRAM

C307789E35
3.552,1.083 4.01,1.281 0.458,0.198 10 false +BS 3.188,1.073 3.646,1.271 0.458,0.198 10 false 38 1.51,1.406 2.323,1.615 0.813,0.208 10 false ABS NO. 2 0.198,1.219 1.01,1.427 0.813,0.208 10 false from Battery 4.531,0.958 5.531,1.167 1,0.208 10 false Solenoid Relay 4.417,3.333 5.604,3.771 1.188,0.438 10 false Skid Control ECU 3.563,4.927 4.021,5.125 0.458,0.198 10 false GND1 3.198,4.938 3.438,5.135 0.24,0.198 10 false 25 3.906,7.885 5.688,8.208 1.781,0.323 10 false Brake Actuator Assembly 3.521,7.896 3.979,8.094 0.458,0.198 10 false A71 6,1.646 6.458,1.844 0.458,0.198 10 false SFRH 6,2.198 6.458,2.396 0.458,0.198 10 false SFLH 6,2.677 6.458,2.875 0.458,0.198 10 false SRRH 5.99,3.198 6.448,3.396 0.458,0.198 10 false SRLH 5.99,3.688 6.448,3.885 0.458,0.198 10 false SFRR 5.99,4.198 6.448,4.396 0.458,0.198 10 false SFLR 5.979,4.719 6.438,4.917 0.458,0.198 10 false SRRR 6,5.219 6.458,5.417 0.458,0.198 10 false SRLR 6,5.729 6.458,5.927 0.458,0.198 10 false SM1 6.01,6.229 6.469,6.427 0.458,0.198 10 false SM2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.RECONFIRM DTC
HINT:
·

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

·

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).




b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1225, C1468, C1469, C146A and C146B are not output A
DTCs C1225, C1468, C1469, C146A and/or C146B are output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





A

B