This DTC is stored when the skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the yaw rate and acceleration sensor (airbag ECU assembly).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1381 | At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more. | ·
A/BAG-IG2 fuse ·
Acceleration sensor (Airbag ECU assembly) ·
Wire harness or connector |
Refer to DTCs C1232, C1243 and C1245 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1232).
When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A58 yaw rate and acceleration sensor (airbag ECU assembly) connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait at least 60 seconds.
Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-21 (IG2) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly)) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-25 (E1) - Body ground | Always | Below 1 Ω |
| A58-26 (E2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly)) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A58 yaw rate and acceleration sensor (airbag ECU assembly) connector.
Clear the DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 3 km/h (2 mph) or more for at least 10 seconds.
Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1381 is not output | A |
| DTC C1381 is output | B |
Check the yaw rate and acceleration sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B