Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.01–2018.07
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM

C256466E47
5.396,1.313 5.677,1.479 0.281,0.167 10 false A71 5.375,1.49 6.99,1.865 1.615,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 3.708,2.698 3.99,2.844 0.281,0.146 10 false J45 3.708,2.885 4.115,3.031 0.406,0.146 10 false DLC3 3.615,2.125 3.865,2.281 0.25,0.156 10 false CG 3.438,2.031 3.552,2.188 0.115,0.156 10 false 4 3.615,1.698 3.844,1.854 0.229,0.156 10 false TC 3.365,1.615 3.563,1.781 0.198,0.167 10 false 13 0.521,2.729 0.802,2.896 0.281,0.167 10 false A56 0.51,2.927 0.885,3.083 0.375,0.156 10 false ECM 1.198,1.615 1.385,1.771 0.188,0.156 10 false 23 0.906,1.708 1.135,1.865 0.229,0.156 10 false TC 1.021,4.229 2.99,4.406 1.969,0.177 10 false : CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION LINE
a.

Check if CAN communication system DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C245481E35
0.104,1.385 0.417,1.583 0.313,0.198 1.615,0.792 1.615,0.25 1.615,0.25 1.76,0.25 true 1.854,1.479 1.854,2.021 1.854,2.021 2.021,2.021 true 1.823,0.167 2.115,0.344 0.292,0.177 10 false CG 2.073,1.938 2.281,2.083 0.208,0.146 10 false TC 0.115,0.115 0.406,0.292 0.292,0.177 10 false *a 0.146,1.396 0.458,1.604 0.313,0.208 10 false J45

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J45-13 (TC) - J45-4 (CG) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of DLC3


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
SST
09843-18040  

a.

Turn the ignition switch to ON.



c.
C245481E35
0.104,1.385 0.417,1.583 0.313,0.198 1.615,0.792 1.615,0.25 1.615,0.25 1.76,0.25 true 1.854,1.479 1.854,2.021 1.854,2.021 2.021,2.021 true 1.823,0.167 2.115,0.344 0.292,0.177 10 false CG 2.073,1.938 2.281,2.083 0.208,0.146 10 false TC 0.115,0.115 0.406,0.292 0.292,0.177 10 false *a 0.146,1.396 0.458,1.604 0.313,0.208 10 false J45

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

Text in Illustration
*a Front view of DLC3


d.

Check that the ABS warning light is blinking.

OK:

The ABS warning light is blinking.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-23 (TC) - J45-13 (TC) Always Below 1 Ω
A56-23 (TC) or J45-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C245481E36
0.104,1.385 0.417,1.583 0.313,0.198 1.615,0.792 1.615,0.25 1.615,0.25 1.76,0.25 true 1.823,0.167 2.115,0.344 0.292,0.177 10 false CG 0.115,0.115 0.406,0.292 0.292,0.177 10 false *a 0.146,1.396 0.458,1.604 0.313,0.208 10 false J45

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3


Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
SST
09843-18040  

a.

Turn the ignition switch to ON.



c.
C245481E35
0.104,1.385 0.417,1.583 0.313,0.198 1.615,0.792 1.615,0.25 1.615,0.25 1.76,0.25 true 1.854,1.479 1.854,2.021 1.854,2.021 2.021,2.021 true 1.823,0.167 2.115,0.344 0.292,0.177 10 false CG 2.073,1.938 2.281,2.083 0.208,0.146 10 false TC 0.115,0.115 0.406,0.292 0.292,0.177 10 false *a 0.146,1.396 0.458,1.604 0.313,0.208 10 false J45

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

Text in Illustration
*a Front view of DLC3


d.

Check that the ABS warning light is blinking.

OK:

The ABS warning light is blinking.



Result:
Proceed to
OK
NG



OK

END

NG