The vehicle stability control system troubleshooting procedures are based on the premise that the CAN communication system is functioning normally. Check the CAN communication system first before troubleshooting the vehicle stability control system.
*: Use the GTS.
| Result |
|---|
| NEXT |
NEXT
Interview the customer and confirm the trouble (Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
| Result |
|---|
| NEXT |
NEXT
Check and record DTC and Freeze Frame Data (for DTC Check/Clear: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR, and for Freeze Frame Data: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>FREEZE FRAME DATA).
Clear the DTC and Freeze Frame Data (for DTC Check/Clear: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR, and for Freeze Frame Data: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>FREEZE FRAME DATA).
Reconfirm the DTC.
Reconfirm the DTC based on the recorded DTC and Freeze Frame Data (for DTC Check/Clear: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR, and for Freeze Frame Data: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>FREEZE FRAME DATA).
When CAN communication system DTCs are output, repair the CAN communication system first (Click here Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If DTC U0100, U0124 or U0126 is output together with a CAN communication DTC, first check the appropriate sensor for a momentary open circuit (Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
If the GTS cannot communicate with the skid control ECU (brake actuator assembly), inspect the CAN communication system (Click here Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If there is no response from the skid control ECU (brake actuator assembly), inspect the +BS circuit of the skid control ECU (brake actuator assembly) (for C1241: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241, for C1417: Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417).
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output (Problem symptom does not occur) | B |
| DTC is not output (Problem symptom occurs) | C |
A
B
C
Proceed to Diagnostic Trouble Code Chart (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
| Result |
|---|
| NEXT |
NEXT
Proceed to Check for Intermittent Problems (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Result |
|---|
| NEXT |
NEXT
Proceed to Problem Symptoms Table (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).
| Result |
|---|
| NEXT |
NEXT
| Result |
|---|
| NEXT |
NEXT
| Result |
|---|
| NEXT |
NEXT
| Result |
|---|
| NEXT |
NEXT
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Check if the same DTCs are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
| Result |
|---|
| NEXT |
NEXT