Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.01–2018.07
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM T

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  PROBLEM SYMPTOMS TABLE  


NOTICE:

When replacing the skid control ECU (brake actuator assembly), sensor, etc., turn the ignition switch off.


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Vehicle Stability Control System
Symptom Suspected Area Link
ABS, brake pressure increase function and/or EBD does not operate. Check for DTCs again and make sure that the normal system code is output. (Click here)
Power source circuit (Low power supply voltage malfunction) (Click here)
Power source circuit (High power supply voltage malfunction) (Click here)
Front speed sensor circuit (Comparison malfunction) (Click here)
Front speed sensor circuit (Open or short malfunction) (Click here)
Front speed sensor circuit (Output malfunction) (Click here)
Rear speed sensor circuit (Comparison malfunction) (Click here)
Rear speed sensor circuit (Open or short malfunction) (Click here)
Rear speed sensor circuit (Output malfunction) (Click here)
Check the skid control ECU (brake actuator assembly) with the GTS. (Check skid control ECU (brake actuator assembly) operation using the Active Test function.) If abnormal, check the hydraulic circuit for leaks. (Click here)
If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the skid control ECU (brake actuator assembly). (Click here)
ABS, brake pressure increase function and/or EBD does not operate efficiently. Check for DTCs again and make sure that the normal system code is output. (Click here)
Front speed sensor circuit (Comparison malfunction) (Click here)
Front speed sensor circuit (Open or short malfunction) (Click here)
Front speed sensor circuit (Output malfunction) (Click here)
Rear speed sensor circuit (Comparison malfunction) (Click here)
Rear speed sensor circuit (Open or short malfunction) (Click here)
Rear speed sensor circuit (Output malfunction) (Click here)
Stop light switch circuit (Open malfunction) (Click here)
Stop light switch circuit (Stuck off malfunction) (Click here)
Check the skid control ECU (brake actuator assembly) with the GTS. (Check skid control ECU (brake actuator assembly) operation using the Active Test function.) If abnormal, check the hydraulic circuit for leaks. (Click here)
If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the skid control ECU (brake actuator assembly). (Click here)
ABS sensor DTC check cannot be done. Check for DTCs again and make sure that the normal system code is output. (Click here)
TC and CG terminal circuit (Click here)
If the symptoms still occur even after the above circuit in the suspected area has been inspected and proved to be normal, replace the skid control ECU (brake actuator assembly). (Click here)
ABS warning light abnormal (Remains on). ABS warning light circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
ABS warning light abnormal (Does not come on). ABS warning light circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
Brake warning light abnormal (Remains on). Brake warning light circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
Brake warning light abnormal (Does not come on). Brake warning light circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
Sensor check cannot be done. TS and CG terminal circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
VSC and/or TRC does not operate. Check for DTCs again and make sure that the normal system code is output. (Click here)
Power source circuit (Low power supply voltage malfunction) (Click here)
Power source circuit (High power supply voltage malfunction) (Click here)
Check the hydraulic circuit for leaks. -
Front speed sensor circuit (Comparison malfunction) (Click here)
Front speed sensor circuit (Open or short malfunction) (Click here)
Front speed sensor circuit (Output malfunction) (Click here)
Rear speed sensor circuit (Comparison malfunction) (Click here)
Rear speed sensor circuit (Open or short malfunction) (Click here)
Rear speed sensor circuit (Output malfunction) (Click here)
Yaw rate and acceleration sensor (airbag ECU assembly) circuit (Zero point malfunction) (Click here)
Yaw rate and acceleration sensor (airbag ECU assembly) circuit (Power supply malfunction) (Click here)
Acceleration sensor (airbag ECU assembly) circuit(Comparison malfunction) (Click here)
Yaw rate sensor (airbag ECU assembly) circuit (Comparison malfunction) (Click here)
Yaw rate and acceleration sensor (airbag ECU assembly) circuit (Stuck or output malfunction) (Click here)
Yaw rate and acceleration sensor (airbag ECU assembly) circuit (Internal malfunction) (Click here)
Steering angle sensor (spiral with sensor cable sub-assembly) circuit (Zero point malfunction) (Click here)
Steering sensor (spiral with sensor cable sub-assembly) circuit (Zero point initialization or calibration malfunction) (Click here)
Steering angle sensor (spiral with sensor cable sub-assembly) circuit (Power supply malfunction) (Click here)
Steering angle sensor (spiral with sensor cable sub-assembly) circuit (Output malfunction) (Click here)
Steering angle sensor (spiral with sensor cable sub-assembly) circuit (Internal malfunction) (Click here)
If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the skid control ECU (brake actuator assembly). (Click here)
VSC sensor DTC check cannot be done. Check for DTCs again and make sure that the normal system code is output. (Click here)
TC and CG terminal circuit (Click here)
If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the skid control ECU (brake actuator assembly). (Click here)
VSC OFF switch abnormal VSC OFF switch circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
Slip indicator light abnormal (Remains on). Slip indicator light circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
Slip indicator light abnormal (Does not come on). Slip indicator light circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
Sensor check cannot be done. TS and CG terminal circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
VSC OFF indicator light abnormal (Remains on) VSC OFF switch circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
VSC OFF indicator light abnormal (Does not come on) VSC OFF switch circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
TRC OFF indicator light abnormal (Remains on) VSC OFF switch circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)
TRC OFF indicator light abnormal (Does not come on) VSC OFF switch circuit (Click here)
Skid control ECU (Brake actuator assembly) (Click here)