The anti-lock brake system troubleshooting procedures are based on the premise that the CAN communication system is functioning normally. Check the CAN communication system first before troubleshooting the anti-lock brake system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Interview the customer and confirm the trouble (Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
| Proceed to |
|---|
| NEXT |
NEXT
Check and record DTC and Freeze Frame Data (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR for DTC Check/Clear, and Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>FREEZE FRAME DATA for Freeze Frame Data).
Clear the DTC and Freeze Frame Data (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR for DTC Check/Clear, and Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>FREEZE FRAME DATA for Freeze Frame Data).
Reconfirm the DTC.
Reconfirm the DTC based on the recorded DTC and Freeze Frame Data (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR for DTC Check/Clear, and Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>FREEZE FRAME DATA for Freeze Frame Data).
If DTC U0100, U0124 or U0126 is output together with a CAN communication DTC, first check the appropriate sensor for a momentary open circuit (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CHECK FOR INTERMITTENT PROBLEMS).
If there is no response from the skid control ECU (brake actuator assembly), inspect the +BS circuit of the skid control ECU (brake actuator assembly) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1241).
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output (Problem symptom does not occur) | B |
| DTC is not output (Problem symptom occurs) | C |
A
B
C
Proceed to Diagnostic Trouble Code Chart (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DIAGNOSTIC TROUBLE CODE CHART).
| Proceed to |
|---|
| NEXT |
NEXT
Proceed to Check for Intermittent Problems (Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
| Proceed to |
|---|
| NEXT |
NEXT
Proceed to Problem Symptoms Table (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT