Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › 2017.01–2018.07
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using GTS)


a.

Check the DTC.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Read the DTCs following the prompts on the GTS screen. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.




b.

Clear the DTC.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Operate the GTS to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


vi.

Clear the DTCs by following the prompts on the GTS.

HINT:

Refer to the GTS operator's manual for further details.





DTC CHECK/CLEAR (When Using SST Check Wire)


a.

Check the DTC.

i.
C400213E02
1.583,0.917 1.583,0.542 true 1.771,1.833 1.771,1.49 true 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 1.49,0.375 1.802,0.573 0.313,0.198 10 false CG 1.708,1.844 2.021,2.042 0.313,0.198 10 false TC

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the ignition switch to ON.


iii.

Observe the blinking pattern of the ABS warning light in order to identify the DTC.

HINT:

If no code appears, inspect the TC and CG terminal circuit, and ABS warning light circuit.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)


iv.

Count the number of blinks of the ABS warning light.

HINT:
·

When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, and then 0.25 seconds off.

·

When one DTC is output, each light will output the same code at 4 second intervals. (For example, code 21 would be output as 2 blinks, a 1.5 second pause, and then 1 blink. Code A6 would be output as 10 blinks, a 1.5 second pause, and then 6 blinks. Code B2 would be output as 11 blinks, a 1.5 second pause, and then 2 blinks.)

·

When 2 or more DTCs are output, each light will output a different code at 2.5 second intervals, and when all codes have been output, there will be a 4 second pause and the sequence will repeat.

·

When multiple codes are stored, they are output in order starting with the lowest DTC number.




v.

Check the details of the DTCs.

ABS DTC
Warning Light Display GTS Display
11 C146E
12 C146F
13 C142B
C146C
14 C146D
21 C1468
22 C1469
23 C146A
24 C146B
25 C1225
31 C1401
C1405
32 C1402
C1406
33 C1403
C1407
34 C1404
C1408
35 C1413
36 C1414
38 C1415
39 C1416
41 C120B
C1241
C1417
43 C1232
C1243
44 C1419
C1420
C1442
45 C1245
46 C1421
C1422
C1423
C1424
C142A
C1449
49 C1425
C1426
51 C1427
C1428
59 C1203
67 C1429
C1430
C1431
94 U0073
95 U0124
97 C1381
98 C1336
A3 C1437
U0100
A4 C1476
C1477
C1479
A6 C144C
C144D
C144F
C145A
A7 C1432
C1433
C1434
A8 C1443
C1435
C1436
A9 C1210
B1 C1201
B2 U0126
B3 C1290
C1439
C1445


vi.

After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.

HINT:

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.




b.

Clear the DTC.

i.
C400213E02
1.583,0.917 1.583,0.542 true 1.771,1.833 1.771,1.49 true 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 1.49,0.375 1.802,0.573 0.313,0.198 10 false CG 1.708,1.844 2.021,2.042 0.313,0.198 10 false TC

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the ignition switch to ON.


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the warning light indicates a normal system code.


v.

Remove SST from the terminals of the DLC3.

HINT:

The DTCs cannot be cleared by disconnecting the battery terminal or the ECU-IG NO. 3 fuse.





END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch to ON.