Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C144C  Brake Booster Pressure Sensor "B" Circuit Low  C144D  Brake Booster Pressure Sensor "B" Circuit High  C145A  Brake Booster Pressure Sensor "B" Power Supply Circuit  C1476  Brake Booster Pressure Sensor Circuit Low  C1477  Brake Booster Pressure Sensor Circuit High  C1479  Abnormal Power Supply Voltage in Brake Booster Pressure Sensor  


DESCRIPTION

The No. 1 vacuum booster pressure sensor (vacuum sensor assembly) and No. 2 vacuum booster pressure sensor (vacuum sensor assembly) detect pressure in the brake booster.

When a malfunction occurs in the No. 1 brake booster pressure sensor (vacuum sensor assembly) and No. 2 brake booster pressure sensor (vacuum sensor assembly), the fail-safe prohibits ABS and brake pressure increase function control and illuminates the ABS warning light.

HINT:

EBD control will continue to the extent that EBD control is possible even after ABS is prohibited.


DTC No. DTC Detection Condition Trouble Area
C144C When the No. 2 brake booster pressure sensor power source voltage is between 4.8 and 5.2 V and the No. 2 brake booster pressure sensor input voltage is less than 0.39 V for 1.2 seconds or more continuously.
·

Vacuum booster pressure sensor2 (vacuum sensor assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C144D When the No. 2 brake booster pressure sensor power source voltage is between 4.8 and 5.2 V and the No. 2 brake booster pressure sensor input voltage is higher than 4.41 V for 1.2 seconds or more continuously.
·

Vacuum booster pressure sensor2 (vacuum sensor assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C145A When the +BS terminal voltage is between 9.5 and 17.4 V and the No. 2 brake booster pressure sensor power source voltage exceeds 5.2 V or is below 4.8 V for 1.2 seconds or more continuously.
·

Vacuum booster pressure sensor2 (vacuum sensor assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C1476 When the No. 1 brake booster pressure sensor power source voltage is between 4.8 and 5.2 V and the No. 1 brake booster pressure sensor input voltage is less than 0.39 V for 1.2 seconds or more continuously.
·

Vacuum booster pressure sensor1 (vacuum sensor assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C1477 When the No. 1 brake booster pressure sensor power source voltage is between 4.8 and 5.2 V and the No. 1 brake booster pressure sensor input voltage is higher than 4.41 V for 1.2 seconds or more continuously.
·

Vacuum booster pressure sensor1 (vacuum sensor assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C1479 When the +BS terminal voltage is between 9.5 and 17.4 V and the No. 1 brake booster pressure sensor power source voltage exceeds 5.2 V or is below 4.8 V for 1.2 seconds or more continuously.
·

Vacuum booster pressure sensor1 (vacuum sensor assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C371703E02
0.354,1.177 0.667,1.375 0.313,0.198 10 false F7 0.333,2.688 0.646,2.885 0.313,0.198 10 false F8 1.958,0.458 2.271,0.656 0.313,0.198 10 false VC 1.938,1.979 2.25,2.177 0.313,0.198 10 false VC 1.958,0.771 2.271,0.969 0.313,0.198 10 false PB 1.948,2.281 2.26,2.479 0.313,0.198 10 false PB 1.969,1.083 2.281,1.281 0.313,0.198 10 false E2 1.958,2.583 2.271,2.781 0.313,0.198 10 false E2 0.354,1.375 2.406,1.729 2.052,0.354 10 false No .1 Vacuum Booster Pressure Sensor 0.323,2.885 2.375,3.24 2.052,0.354 10 false No. 2 Vacuum Booster Pressure Sensor 0.542,3.385 2.417,3.625 1.875,0.24 10 false Vacuum Sensor Assembly 3.469,1.469 4.208,1.677 0.74,0.208 10 false Shielded 3.469,2.979 4.208,3.188 0.74,0.208 10 false Shielded 2.26,0.385 2.49,0.583 0.229,0.198 10 false 3 2.26,0.688 2.49,0.885 0.229,0.198 10 false 1 2.271,0.99 2.5,1.188 0.229,0.198 10 false 2 2.25,1.875 2.479,2.073 0.229,0.198 10 false 3 2.26,2.177 2.49,2.375 0.229,0.198 10 false 1 2.271,2.479 2.5,2.677 0.229,0.198 10 false 2 5.354,0.365 5.667,0.563 0.313,0.198 10 false 20 5.354,0.656 5.667,0.854 0.313,0.198 10 false 34 5.344,0.969 5.656,1.167 0.313,0.198 10 false 21 5.458,2.448 5.771,2.646 0.313,0.198 10 false 9 5.427,2.156 5.74,2.354 0.313,0.198 10 false 32 5.458,1.854 5.771,2.052 0.313,0.198 10 false 7 5.677,0.479 6.094,0.677 0.417,0.198 10 false VSM 5.688,0.781 6.104,0.979 0.417,0.198 10 false VSI1 5.677,1.073 6.094,1.271 0.417,0.198 10 false VSG 5.667,1.948 6.167,2.146 0.5,0.198 10 false VSM2 5.667,2.25 6.167,2.448 0.5,0.198 10 false VSI2 5.667,2.542 6.167,2.74 0.5,0.198 10 false VSG2 5.115,3.01 6.646,3.385 1.531,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 5.135,2.813 5.563,3 0.427,0.188 10 false A71

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VACUUM SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the F7 and F8 vacuum sensor assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
No. 1 Vacuum Booster Pressure Sensor
Tester Connection Condition Specified Condition
A71-20 (VSM) - F7-3 (VC) Always Below 1 Ω
A71-20 (VSM) or F7-3 (VC) - Body ground Always 10 kΩ or higher
A71-34 (VSI1) - F7-1 (PB) Always Below 1 Ω
A71-34 (VSI1) or F7-1 (PB) - Body ground Always 10 kΩ or higher
A71-21 (VSG) - F7-2 (E2) Always Below 1 Ω
A71-21 (VSG) or F7-2 (E2) - Body ground Always 10 kΩ or higher

No. 2 Vacuum Booster Pressure Sensor
Tester Connection Condition Specified Condition
A71-7 (VSM2) - F8-3 (VC) Always Below 1 Ω
A71-7 (VSM2) or F8-3 (VC) - Body ground Always 10 kΩ or higher
A71-32 (VSI2) - F8-1 (PB) Always Below 1 Ω
A71-32 (VSI2) or F8-1 (PB) - Body ground Always 10 kΩ or higher
A71-9 (VSG2) - F8-2 (E2) Always Below 1 Ω
A71-9 (VSG2) or F8-2 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SUPPLY OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SUPPLY OUTPUT)
a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.


b.
C323043E02
0.198,0.802 0.615,1.031 0.417,0.229 0.208,1.177 0.625,1.406 0.417,0.229 1.24,1.688 1.615,1.281 true 2.146,1.688 1.875,1.292 true 0.198,0.115 0.51,0.313 0.313,0.198 10 false *a 0.323,0.833 0.635,1.031 0.313,0.198 10 false F7 0.344,1.208 0.656,1.406 0.313,0.198 10 false F8 0.771,0.833 1.083,1.031 0.313,0.198 10 false *A 1.146,1.74 1.458,1.938 0.313,0.198 10 false E2 2.083,1.719 2.396,1.917 0.313,0.198 10 false VC 0.771,1.208 1.083,1.406 0.313,0.198 10 false *B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
No. 1 Vacuum Booster Pressure Sensor
Tester Connection Condition Specified Condition
F7-3 (VC) - F7-2 (E2) Ignition switch ON 4.75 to 5.25 V

No. 2Vacuum Booster Pressure Sensor
Tester Connection Condition Specified Condition
F8-3 (VC) - F8-2 (E2) Ignition switch ON 4.75 to 5.25 V


Text in Illustration
*A No. 1 Vacuum Booster Pressure Sensor
*B No. 2 Vacuum Booster Pressure Sensor
*a Front view of wire harness connector
(to Vacuum Sensor Assembly)


Result:
Proceed to
OK
NG



OK

NG